VBM15R30S
Product Specifications
VBM15R30S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM15R30S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM15R30S: 500 V and 30 A at 140 milliohm
The VBM15R30S is a single N channel MOSFET in a TO220 body rated at 500 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 30 A of drain current and 140 milliohm at a 10 V gate. The die is listed as SJ multiple epitaxy.
Five hundred volts is the class for a 230 V AC line rectified, which gives about 325 V, and for a 350 V DC bus with a modest transient allowance. It is the smallest class that covers a 230 V single phase input with real margin, and it is the class used in the front end of a small drive, a charger and an inverter.
One hundred and forty milliohm at 30 A is 126 W. At 10 A it is 14 W. At 5 A it is 3.5 W. On a TO220 with a heatsink the working current is 8 to 12 A, and on the tab alone it is 3 to 4 A.
Key data for the VBM15R30S
| Configuration | Single N channel |
| Package | TO220 through hole with a metal tab |
| VDS | 500 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 30 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 140 milliohm |
| Technology | SJ multiple epitaxy |
| Loss at 5 A | 3.5 W at 140 milliohm |
| Loss at 10 A | 14 W at 140 milliohm |
| Loss at 30 A | 126 W at 140 milliohm |
| Gate charge | Not printed, ask for the curve before fixing a frequency |
Five hundred volts and the rectified mains
A 230 V AC line rectified into a capacitor gives 325 V DC, and the top of the tolerance plus the ripple can reach 375 V. A part at 500 V has 125 V of margin, which covers a switching spike and a modest surge. A part at 600 V has 225 V and is the safer choice where the line is known to be dirty.
In a power factor stage or a flyback the drain also sees the reflected voltage plus the leakage spike, so the number that has to stay under 500 V is the bus plus the reflected voltage plus the spike. On a flyback with a 100 V reflected voltage and a 100 V spike from a 375 V bus the sum is 575 V, which is past this part and inside a 650 V one.
That arithmetic is where most of these decisions are made. The class is chosen from the sum of the three voltages rather than from the bus alone, and the clamp or snubber is what keeps the third term small.
Multiple epitaxy at five hundred volts.
The multiple epitaxy structure gives a resistance per unit area close to the best available at this voltage and a body diode with a moderate recovery. It is a good compromise for a converter between 20 and 60 kHz, which is where most 230 V front ends run.
Recovery of the body diode at 10 A and 375 V is a few watts in the opposite switch of a bridge, and it has to be counted. In a flyback there is no opposite switch, so the diode only matters when the part is used in a bridge or a synchronous configuration.
The output capacitance stores energy that is lost at every turn on. At 375 V and 50 kHz a die of this size loses a couple of watts in that path, which is comparable to the conduction loss at 3 A. That is why a small front end runs at 30 to 50 kHz rather than at 100 kHz.
Heatsink and the source lead
At 10 A the loss is 14 W and a TO220 tab on a small clip on heatsink holds it. The tab is the drain and it sits at 375 V, so the heatsink is live unless an insulator is fitted. A silicone pad costs about 0.5 degrees per watt and is the usual choice for a part at this voltage.
The source leaves through the leads, and at 10 A the lead resistance is a small but real part of the path. A wide copper pour on both sides of the board with the leads soldered through is the way the lead resistance and the loop inductance are both reduced.
Gate drive at 10 V with a 30 V window leaves a lot of margin, which is useful at 375 V because the drain to gate capacitance couples a displacement current into the gate at every transition. A driver of half an amp with a 10 to 22 ohm resistor is the normal arrangement.
Where the part fits and where it does not
It fits a 230 V AC front end power factor stage at 5 to 10 A, a flyback at 30 to 50 kHz, a small inverter, an active clamp and a start up circuit on a 375 V bus. It does not fit a 400 V bus with regeneration, a flyback with a high reflected voltage, or a load near 30 A in a TO220.
For a 230 V front end the questions are the sum of bus, reflected voltage and spike, the clamp and the diode recovery. Our date code management page covers how a reel held between builds is tracked and when it is set aside.
The sourcing side of this part is covered on the safety stock planning. For a 500 V part on a continuous build, that page covers how a buffer is sized against the plan.
Questions we get on this code
Does 500 V cover a 230 V AC line? It covers a 325 V bus with 175 V of margin. In a flyback the reflected voltage and the spike have to be added, and that can exceed 500 V.
Is 30 A available? At 126 W, no. On a clip on heatsink 8 to 12 A is the working range, and on the tab alone 3 to 4 A.
Does the tab need an insulator? Yes. The tab is the drain at 375 V, so a heatsink shared with anything else needs an insulator and a shoulder washer.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.