VBM155R13
Product Specifications
VBM155R13
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM155R13 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM155R13: a 550 V, 0.43 ohm die for power factor correction
The VBM155R13 is a 550 V N channel MOSFET in the TO-220AB body, printed at 0.43 ohm with a 10 V gate and 10 A flowing, 13 A of continuous drain current with the case at 25 C, 258 W of dissipation and a 150 C junction. The sheet lists consumer displays, server and telecom power supplies, welding, induction heating, motor drives, battery chargers and power factor correction as intended uses.
The most quoted number on a part like this is the on resistance, and the most useful one is the gate charge maximum. Here the typical gate charge is 85 nC and the maximum is 160 nC, which is a 88 per cent spread on a single part number. A driver sized on the typical figure will be short of current on a worst case lot, and the difference shows up as slower switching and more loss rather than as a failure that can be traced easily.
The ratings a buyer checks first
| Drain to source voltage | 550 V |
| Gate to source voltage, DC and AC above 1 Hz | plus or minus 20 V and 30 V |
| On resistance at 10 V gate, 10 A | 0.43 ohm typical |
| Continuous drain current, case at 25 C and 100 C | 13 A and 6 A |
| Pulsed drain current | 42 A |
| Single pulse avalanche energy | 242 mJ at 7.5 A from 10 mH |
| Dissipation with the case at 25 C | 258 W |
| Linear derating factor | 2.1 W per C |
| Junction to case and junction to ambient | 0.45 and 40 C per watt |
| Gate threshold at 250 microamp | 2 V minimum, 4 V maximum |
| Forward transconductance at 10 A | 12 S typical |
| Input capacitance at 100 V | 2784 pF typical |
| Output capacitance and reverse transfer capacitance | 152 and 13 pF |
| Effective output capacitance, energy and time related | 131 and 189 pF |
| Total gate charge at 400 V, 10 A | 85 nC typical, 160 nC maximum |
| Gate source and gate drain charge | 14 and 28 nC |
| Turn on delay and rise time | 24 and 31 ns typical |
| Turn off delay and fall time | 117 and 56 ns typical |
| Body diode forward drop at 10 A | 1.2 V maximum |
| Body diode recovery time and charge | 437 ns and 5.9 microcoulomb |
| Drain source slope at 125 C, reverse diode slope | 24 and 0.36 V per ns |
Reading the electrical table instead of the front page
The current row is a case temperature row and nothing else. Thirteen amps is quoted with the case at 25 C, which nobody achieves in a real supply, and the same row at a 100 C case is 6 A. A 150 W adapter that carries 1 A average through the switch at a 30 per cent duty cycle is comfortable; a 400 W unit that carries 3 A is not, and the decision should be made on the 6 A figure with a heatsink that actually reaches 70 C to 80 C.
The diode rows decide whether this part can be used in a bridge. The reverse recovery time is 437 ns and the recovered charge is 5.9 microcoulomb, which is a slow diode by modern standards, and the reverse diode slope is printed as 0.36 V per nanosecond. On a 400 V bus that slope means the commutating edge has to be slower than about 1.1 microseconds, or the diode's own recovery current will be the thing that limits the circuit. In a continuous mode power factor stage the diode that recovers is the boost diode rather than this switch, so the figure matters mostly in a bridge or a synchronous stage.
The effective output capacitance is worth a second look. The time related value is 189 pF against an energy related value of 131 pF, and the charge stored at 400 V is roughly half of 189 pF times the square of 400 V, about 15 microjoule per cycle. At 100 kHz that is 1.5 W of hard switched turn on loss that no gate resistor can remove. It is the reason a 550 V planar part is usually found in a soft switched or a discontinuous stage rather than in a hard switched one at high frequency. The gate charge spread matters in the same way, since a driver that puts 85 nC into the gate in 20 ns needs nearly twice the current for the 160 nC maximum.
Where a 550 V part earns its place
Five hundred and fifty volts covers a single phase 220 V AC input after rectification, where the bulk capacitor sits near 380 V to 400 V, with about 37 per cent of margin for a mains surge. That is the classic boundary mode power factor stage in a 75 W to 250 W adapter, and it is also the voltage class used in welding inverters and induction heating, where the switching frequency is low enough that the slow body diode does not matter.
The second home is a battery charger or a motor drive fed from a rectified single phase mains, where the current is low and the thermal budget is dominated by the bridge rectifier rather than by the switch. The 242 mJ avalanche rating from 10 mH at 7.5 A is generous for the class and covers the leakage of a small transformer without an external clamp, which is why the part appears in flyback auxiliaries as well as in power factor stages. The 42 A pulsed rating is the row to check for an inrush event, because a surge that runs through the switch instead of through a resistor is limited by that figure and not by the continuous one.
Sourcing notes and the second source question
This is a planar 500 V to 600 V class part, and the segment is being steadily narrowed as vendors move their lines to super junction. That makes last time buy planning more relevant than lead time for a long life product. The last time buy and long term buy planning page sets out how a bridge quantity is calculated from the remaining build schedule, the storage life of the package and the cost of carrying the stock.
Where a substitute is needed, the columns that matter are the recovered charge, the gate charge maximum and the junction to case. A super junction part with the same voltage and half the on resistance will switch much faster and can make an existing snubber or an existing transformer ring; the power management cross reference page keeps the recovered charge beside the resistance for that reason, and it flags the parts whose gate charge maximum is more than 50 per cent above the typical.
Questions we answer before a reel is booked
First, what the gate waveform looks like. The sheet gives plus or minus 20 V for a DC gate and 30 V peak to peak for an AC gate above 1 Hz, which is a narrower window than it first appears. A gate transformer or a drive with ringing that reaches plus or minus 18 V sits inside the DC rating and outside the AC one, so a clamp is worth having.
Second, what the switching test conditions were. The printed times were taken with a 9.1 ohm gate resistor at 400 V and 10 A. A board with a 22 ohm resistor will be roughly twice as slow, and a board with 4.7 ohm will ring. The gate charge maximum of 160 nC is the figure a driver has to supply, not the 85 nC typical.
Third, what the first article measures. On a 550 V planar part the parameters that move between lots are the threshold, the on resistance at 10 V and the recovered charge. A sample plan that measures all three on a few parts per lot, at a controlled temperature, catches the drift that a single cold measurement misses. Our incoming inspection plan describes a sample size that is workable for a tube packed power device. The 550 V class also shows a real spread in breakdown voltage between lots, so a hot breakdown measurement belongs on the first article of a mains connected product.