VBM1405
Product Specifications
VBM1405
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM1405 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM1405: a 40 V, 6 milliohm switch built for a 4.5 V gate
The VBM1405 is a 40 V N channel trench MOSFET in the TO-220AB body, printed at 6 milliohm with a 10 V gate and 7 milliohm with a 4.5 V gate, 110 A of continuous drain current with the case at 25 C, and a 150 C junction. The same body and the same thermal stack as the 3 milliohm member of the family, with a die that is twice the resistance and a threshold window that starts at 1.2 V.
That pair of resistance rows is the reason the part exists. Where most 40 V parts double their resistance when the gate drops to 4.5 V, this one moves by about 17 per cent, so a board with a 5 V gate drive and a small series resistor can use the same die as a 10 V board and lose very little. The threshold window that starts at 1.2 V is the price of that, and it is a real one on a board with a fast switching node nearby.
The ratings a buyer checks first
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A | 6 milliohm typical |
| On resistance at 4.5 V gate, 20 A | 7 milliohm typical |
| Continuous current, case at 25 C and 70 C | 110 A and 90 A |
| Continuous current, ambient at 25 C and 70 C | 31 A and 25 A |
| Package limitation current | 110 A |
| Pulsed drain current | 270 A |
| Avalanche current and single pulse energy | 85 A and 320 mJ |
| Diode continuous current, case at 25 C | 110 A |
| Dissipation, case at 25 C and 70 C | 312 W and 200 W |
| Dissipation, ambient at 25 C and 70 C | 3.13 W and 2.0 W |
| Junction to ambient, typical and maximum | 32 and 40 C per watt |
| Junction to case, typical and maximum | 0.33 and 0.4 C per watt |
| Gate threshold at 250 microamp | 1.2 V minimum, 2.5 V maximum |
| Threshold temperature coefficient | minus 8 mV per C |
| Input, output and reverse transfer capacitance | 2900, 750 and 310 pF |
| Total gate charge at 20 V, 20 A | 130 nC typical |
| Gate source and gate drain charge | 20 and 32 nC |
| Switching at a 10 V gate, turn off delay and fall | 77 and 10 ns typical |
| Switching at a 4.5 V gate, turn off delay and fall | 180 and 60 ns typical |
| Body diode forward drop at 20 A | 0.8 V typical, 1.2 V maximum |
| Body diode recovery time and charge | 50 ns and 70 nanocoulomb |
Reading the electrical table instead of the front page
The two resistance rows are close enough that the choice of gate drive stops being the dominant question, which is not true of the 3 milliohm part beside it on the same family sheet. Set the two side by side and the reason for having both is clear: at a 10 V gate the 3 milliohm part has half the conduction loss, and at 4.5 V the 6 milliohm part has less than half of what the other one becomes. A product family that uses both can be optimised per rail without changing the footprint.
| Parameter | VBM1403 | VBM1405 |
| On resistance at 10 V gate | 3 milliohm | 6 milliohm |
| On resistance at 4.5 V gate | 15 milliohm | 7 milliohm |
| Gate threshold window | 2.0 to 4.0 V | 1.2 to 2.5 V |
| Input capacitance | 5500 pF | 2900 pF |
| Total gate charge | 120 nC | 130 nC |
| Package limitation current | 110 A | 110 A |
The second thing to notice is the thermal stack, which is identical on both parts and is the real constraint. With 3.13 W allowed in free air and 6 milliohm of resistance, the part carries about 23 A on a bare board before the junction reaches its limit; with a heatsink holding the case at 25 C the package limit of 110 A arrives first. The 312 W case figure exists mainly to describe a pulsed condition, not a continuous one.
The third thing is the threshold. A minimum of 1.2 V is low for a power MOSFET and it is deliberate, since a low threshold is what makes the 4.5 V row usable. The consequence is that a 1 V spike on the gate, from a drain node that swings 40 V in 10 ns through 310 pF of reverse transfer capacitance, will turn the part partly on. A 10 k pull down at the gate and a series resistor are not optional extras on this part; they are part of the application circuit.
Where a 40 V logic level part earns its place
Battery powered products with a 24 V pack and a 5 V logic rail are the natural home: power tools, e-bike controllers, small pumps and fans, and portable test equipment. In each of them the gate drive comes from a logic output or a small charge pump rather than a dedicated 10 V supply, and the 4.5 V row is the one that matters. The low threshold also suits a board that runs the driver from a 3.3 V rail through a level shifter, as long as the pull down is in place.
The second use is synchronous rectification in a 12 V output converter where the controller drives the gate from a 5 V rail. There the 2900 pF input capacitance and 130 nC of gate charge are the numbers that set the driver loss, and they are lower than the 3 milliohm part beside it, which makes this the easier device to drive at high frequency even though its conduction loss is higher.
Sourcing notes and the second source question
When this part is cross referenced the 4.5 V column is the one to compare, not the 10 V column. A candidate that prints 6 milliohm at 10 V and 20 milliohm at 4.5 V looks identical in the summary and is unusable on a 5 V gate drive. The power management cross reference page holds both columns for that reason, and the guide to verifying a drop in replacement sets out the bench checks that catch a threshold difference before it reaches a customer.
The other substitution risk is the gate. A part with a 1.2 V minimum threshold and a substitute with a 2.0 V minimum will both work on a 10 V driver and behave differently on a 4.5 V one, especially at low temperature where the threshold rises. Where a programme alternates between two approved parts, we ask for the low temperature threshold of both and keep the colder figure in the file, since that is the one that decides whether the part turns on at minus 20 C.
Questions we answer before a reel is booked
First, what the gate drive is, since that decides which of the two family members is right. A 10 V driver should use the 3 milliohm part and a 5 V driver should use this one; using this part on a 10 V driver gives away half the conduction loss for nothing, and using the other one on 5 V costs five times the resistance.
Second, whether the gate has a pull down. With a 1.2 V minimum threshold, a floating gate is a short circuit waiting for a reason. The 20 V gate rating gives room for a spike, but the part does not need 20 V to conduct, only about 2 V, which is why the resistor and the track routing matter more here than on a high threshold device.
Third, what the first article measures. The on resistance at 4.5 V, the threshold at both temperature extremes and the body diode drop are the three that move between lots. The avalanche rating of 320 mJ is high for a 40 V part and covers most inductive loads without a clamp, but a repeated event still belongs on the repetitive curve rather than on the single pulse figure. Where the customer wants the sample plan in writing, the incoming inspection plan sets out the measurements per lot at a controlled temperature.