VBM1202N
Product Specifications
VBM1202N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM1202N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM1202N: a 200 V switch for 110 V class buses and battery packs
The VBM1202N is a 200 V N channel MOSFET in the TO-220AB body with a 175 C junction, printed at 0.017 ohm with a 10 V gate and 0.018 ohm with a 7.5 V gate, 80 A of continuous drain current with the case at 25 C, and 64 nC of total gate charge. The application list on the sheet names uninterruptible supplies, AC to DC switch mode supplies, lighting, synchronous rectification, DC to DC conversion, motor drive, DC to AC inversion, solar micro inverters and class D audio.
Two rows in the summary are unusual enough to be worth pointing out before anything else. The first is the 7.5 V gate row, since a 7.5 V rail is not a common gate supply and the printed resistance is only 6 per cent above the 10 V value. The second is the current row, which is written at a 150 C junction while the device is rated to 175 C. The two statements are not the same and a thermal budget should use the lower one.
The ratings a buyer checks first
| Drain to source voltage | 200 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A | 0.017 ohm typical |
| On resistance at 7.5 V gate, 30 A | 0.018 ohm typical |
| Continuous drain current, case at 25 C and 70 C | 80 A and 65 A |
| Pulsed drain current for 100 microseconds | 240 A |
| Avalanche current and single pulse energy | 60 A and 180 mJ |
| Dissipation, case at 25 C and 125 C | 375 W and 125 W |
| Junction to case and junction to ambient | 0.4 and 40 C per watt |
| Gate threshold at 250 microamp | 2 V minimum, 4 V maximum |
| On state drain current at 10 V gate | 90 A minimum |
| Forward transconductance at 30 A | 75 S typical |
| Input capacitance | 4132 pF typical |
| Output and reverse transfer capacitance | 246 and 21 pF typical |
| Total gate charge at 100 V, 60 A | 64 nC typical, 96 nC maximum |
| Gate source and gate drain charge | 16.7 and 16.9 nC |
| Gate resistance | 1.5 minimum, 3 typical, 5 maximum |
| Turn on delay and rise time | 13 and 112 ns typical |
| Turn off delay and fall time | 35 and 80 ns typical |
| Body diode forward drop at 10 A | 0.8 V typical, 1.2 V maximum |
| Body diode reverse recovery time and charge | 160 ns and 0.9 microcoulomb |
Reading the electrical table instead of the front page
The important omission on this sheet is that no hot on resistance row is printed at all. The 0.017 and 0.018 ohm values are stated at the 25 C test temperature and nothing follows them at 125 C. For a 200 V trench device a factor of 1.6 to 1.8 between a cold and a hot die is normal, which would put the hot value near 0.029 ohm. That changes the arithmetic a great deal: 80 A through 0.017 ohm is about 109 W, and the same 80 A through 0.029 ohm is about 186 W.
The dissipation rows say 375 W with the case at 25 C and 125 W with the case at 125 C. Dividing the second by the square of the current gives the maximum hot resistance that keeps 80 A inside the budget, which is 0.0195 ohm. If the die really does drift towards 0.029 ohm the part cannot carry 80 A with a 125 C case, and the honest continuous figure is closer to 65 A, which happens to be the row the sheet prints at a 70 C case. A customer who needs the full current should measure the hot value on a first article rather than assume the cold row.
The dynamic figures are good for the class. A reverse transfer capacitance of 21 pF with 246 pF of output capacitance means the drain node settles quickly and the Miller plateau is short, and 64 nC of total gate charge is light for a 200 V die of this size. The body diode is ordinary rather than fast, with 160 ns recovery and 0.9 microcoulomb of recovered charge, so a bridge built from these needs either enough dead time or a parallel Schottky.
Where a 200 V part earns its place
Two hundred volts covers a 110 V AC mains input after rectification, where the peak is about 155 V, and it covers 96 V battery packs with margin for a charger overshoot. It covers a split rail class D amplifier running plus and minus 80 V, and it covers the low voltage side of a solar micro inverter where the panel string sits below 150 V. It does not cover a 220 V AC input, where the rectified bus is 311 V, and a board that tries it will fail on the first mains surge.
The second home is a bidirectional DC to DC stage in a battery system, where two of these in a half bridge commutate a 96 V pack against a 48 V rail. There the 246 pF output capacitance and the 0.9 microcoulomb of recovered charge set the dead time loss, and the 175 C junction gives thermal headroom for the short overload that a motor start produces. For a purely resistive load the part is more switch than the job needs, and a 150 V device with lower charge would be cheaper to drive.
Sourcing notes and the second source question
Two hundred volt parts in the 0.015 to 0.020 ohm range are made by several vendors and the differences sit in the gate charge and in the hot resistance, not in the headline number. When we look for a second source we compare the 125 C row first, and if the candidate sheet does not print one we ask the vendor for it. Our power management cross reference page carries a column for exactly that case, because a missing hot row is not evidence of a good one.
On supply, this class is used heavily in mains adapters and lighting drivers, so the market is deep and the lead time is usually weeks rather than months. The awkward case is a board that has been qualified around one vendor and then needs a second part on a different die, since the driver and the snubber may need to change. The BOM shortage recovery page describes how that substitution is run without stopping the line, and what the customer signs before the first substituted unit ships. Where the substitute comes from a vendor we have not used before, the supplier onboarding checklist is what we work through first, because a first article from an unknown line tells you very little about the second lot.
Questions we answer before a reel is booked
The first question is the gate drive. The threshold window runs from 2 V to 4 V, and the only two printed resistance rows are at 10 V and 7.5 V. A 10 V driver is the safe choice; a 7.5 V rail is supported on paper and is worth confirming with a first article rather than trusting the table alone, since a 7.5 V rail with any droop lands in unspecified territory.
The second question is the thermal path. At 65 A and 0.029 ohm a hot die makes about 122 W, which is roughly the whole allowance at a 125 C case, so the tab has to be on a heatsink with a known thermal resistance. In free air the 40 C per watt figure caps the part at a few watts, which is the right way to use it in a standby supply and the wrong way in a motor drive. The 175 C junction rating is not a licence to run the die there, since every row that matters gets worse long before the limit is reached.
The third question is the diode. A 160 ns recovery with 0.9 microcoulomb of charge is not a fast diode, and in a bridge that commutates a 96 V rail the resulting loss lands on the opposite switch. Where the topology is hard switched, a parallel Schottky or a resonant transition pays for itself; where it is a simple buck with a freewheel interval long enough to let the diode recover, the part is fine as it stands.