VBM1201N
Product Specifications
VBM1201N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM1201N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM1201N: 200 V and 100 A at 8 milliohm
The VBM1201N is a single N channel MOSFET in a TO220 body rated at 200 V drain to source, plus or minus 20 V on the gate, a 4 V threshold, 100 A of drain current and 8 milliohm at a 10 V gate. The die is a trench part.
Two hundred volts is the class for a 110 V DC bus, a 120 V rail, a 96 V string with a wider transient allowance than a 150 V part gives, and the primary side of a converter fed from a 110 V battery. It is also the class used in telecom rectifiers and in small inverter front ends.
Eight milliohm at 100 A is 80 W, which is a heatsink figure rather than a package figure. At 40 A the loss is 12.8 W and a modest heatsink holds it. At 20 A it is 3.2 W and the tab alone does the job. The die is large for the package and the thermal path is the limit.
Key data for the VBM1201N
| Configuration | Single N channel |
| Package | TO220 through hole with a metal tab |
| VDS | 200 V |
| VGS | Plus or minus 20 V |
| Vth | 4 V |
| ID | 100 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 8 milliohm |
| Technology | Trench |
| Loss at 20 A | 3.2 W at 8 milliohm |
| Loss at 40 A | 12.8 W at 8 milliohm |
| Loss at 100 A | 80 W at 8 milliohm |
| Thermal path | The tab is the drain and it carries the whole loss into the heatsink |
A four volt threshold and what it rules out
A 4 V threshold is high for a low voltage trench part and it is what a 200 V die needs to stay off while the drain swings. The cost is that a 5 V logic output gives only 1 V of overdrive, which is inside the region where the resistance is much higher than the published figure.
The resistance column is at 10 V, which is where this part should be driven. A 10 V drive with a 20 V window leaves 10 V of margin for ringing, which is enough on a rail where the switching node moves fast but not generous.
Where the drive has to come from a 12 V housekeeping rail, the 10 V figure applies closely. Where it comes from a 5 V rail, the loss budget has to use a curve, and a loss budget that assumes 8 milliohm at 5 V will run hotter than the arithmetic says.
Two hundred volts on a 110 V bus.
A 110 V DC bus sits at 110 V nominal and can reach 130 V at the top of a charge or during a regeneration event. A 200 V part has 70 V of margin, which covers a switching spike with a short loop and a snubber and does not cover an unclamped surge from a long cable.
Where the input is a 110 V battery, the top of charge is nearer 126 V and the margin is comfortable. Where the input is a rectified 120 V AC line, the DC bus is about 170 V and the 200 V class has only 30 V of margin, which is the case where a 250 V part is the safer choice.
The part also sees the recovery of any diode in the loop and the energy stored in the leakage inductance of a transformer. On a flyback primary at 110 V the drain spike is the bus plus the reflected voltage plus the leakage spike, and the sum is what has to stay under 200 V.
Thermal path in a TO220 at eight milliohm
At 8 milliohm the die is small enough that the tab and the heatsink dominate. A TO220 tab bolted to an aluminium heatsink with a pad has a junction to case resistance of about one degree per watt, so 12.8 W at 40 A gives a case about 13 degrees above the heatsink. With a heatsink at 60 C that is a junction of 73 C, which is comfortable.
At 80 W the same arithmetic gives a case 80 degrees above the heatsink, which is past the limit unless the heatsink is large and the airflow real. That is why the printed current is a figure for a case held at 25 C, a condition a real heatsink cannot hold at that loss.
The insulator under the tab is part of the path. A silicone pad costs about 0.5 degrees per watt and a thin mica with grease costs less, and at 12 W that difference is a few degrees. It matters more at 40 A than at 20 A, and it is a choice made once at the mechanical stage.
Where the part fits and where it does not
It fits a 110 V motor drive at 20 to 40 A, a 96 V battery disconnect, a synchronous rectifier on a 48 V output, a 110 V bus hot swap and the primary switch of a converter fed from a 110 V pack. It does not fit a rectified 120 V AC line without a clamp, a load above about 40 A without a real heatsink, or a surface mount assembly.
For a 110 V bus the questions are the top of charge voltage, the clamp and the material plan that keeps the build supplied. Our material requirements planning page covers how a part on a long build is scheduled against the plan rather than against the last order.
The sourcing side of this part is covered on the vendor consolidation. For a platform that uses several parts at this voltage, that page covers which lines stay dual sourced after a consolidation.
Questions we get on this code
Can it take 100 A? At 80 W it needs a large heatsink and airflow. On a normal TO220 heatsink 30 to 40 A continuous is the working figure.
Does it work on a rectified 120 V AC line? The bus is about 170 V and the margin is 30 V, which is thin. A clamp and a snubber are needed, or a 250 V part.
Is the gate window 20 V a limit here? Yes. A 10 V drive with 10 V of margin is fine. A 15 V drive with overshoot approaches the limit and a gate clamp is worth having.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.