Contact Us

VBM115MR03

Brand: VBsemi
VBsemi VBM115MR03 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM115MR03 — Discrete & Power Semiconductors | Superb Automation

VBM115MR03

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM115MR03 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM115MR03: 1500 V and 3 A in a TO220 body

The VBM115MR03 is a single N channel MOSFET in a TO220 body rated at 1500 V drain to source, plus or minus 30 V on the gate, a 4.5 V threshold, 3 A of drain current and 6000 milliohm at a 10 V gate. The die is planar, which is the process that survives at this voltage where the charge balance structures become difficult to control.

Fifteen hundred volts is the class for a 1000 V photovoltaic string, a high voltage capacitor bank, an x-ray supply, a piezo driver and a high voltage bias supply. It is a small current part with a huge voltage rating, and everything about the way it is used follows from that.

Six thousand milliohm at 3 A is 54 W. At 1 A it is 6 W. At 0.3 A it is 0.54 W. The published current is a die figure and the resistance is the number to plan with, at a working current an order of magnitude below the label.

Key data for the VBM115MR03

ConfigurationSingle N channel
PackageTO220 through hole with a metal tab
VDS1500 V
VGSPlus or minus 30 V
Vth4.5 V
ID3 A, a die figure at a 25 C case
RDS(on) at 10 V6000 milliohm
TechnologyPlanar
Loss at 0.3 A0.54 W at 6000 milliohm
Loss at 1 A6 W at 6000 milliohm
Loss at 3 A54 W at 6000 milliohm
Gate drive10 V or more; the 4.5 V threshold leaves no margin for a 5 V logic level

Why a planar die at 1500 V

Charge balance structures lower the resistance per unit of breakdown voltage by shaping the field in the drift region, and at 1500 V that shaping is hard to make stable over temperature and over the life of the part. A planar die gives up resistance for a breakdown that is predictable, which is the right trade in a part used at a few hundred milliamps.

The result is a large die for a small current. Most of the silicon area exists to hold the voltage, not to conduct, which is why the resistance is 6000 milliohm and the current label is 3 A. That ratio is normal at this voltage and it is the reason the part is chosen for voltage rather than for current.

The capacitance of a die this size is significant. At 1000 V the energy stored in the output capacitance is not trivial, and every turn on discharges it into the channel. At a low switching frequency that is a small average loss. At 50 kHz it can dominate the conduction loss.

Creepage, clearance and the package limit.

Fifteen hundred volts at the pins of a TO220 is near the limit of what the package can hold in a polluted environment. The pin pitch is 2.54 mm, and the creepage between the drain tab and the gate lead is a few millimetres, so the part depends on a coated board or a conformal coat to hold its rating in a humid product.

Clearance is the other half. At 1500 V a bare air gap of 3 mm is not enough for a product that claims pollution degree 2, and the board has to route the high voltage node away from everything else. A slot in the board, a longer creepage path and a coat are the usual answers, and they belong in the mechanical drawing rather than in the circuit notes.

The tab is the drain and it sits at the full rail. A heatsink bolted to it is a live surface at 1500 V, which is a safety item rather than a thermal one. Where a heatsink is needed, an insulator rated for the voltage and a shoulder washer are mandatory.

Driving a 4.5 V threshold at high voltage

The threshold is 4.5 V, which is the highest in this band, and it is high on purpose: at 1500 V the drain to gate capacitance can couple a large displacement current into the gate, and a higher threshold gives more room before that current turns the device on. The cost is that a 5 V drive leaves almost no overdrive.

The gate needs 10 V or more to reach the published resistance. Where the driver sits on the high side it needs an isolated supply, and at 1500 V the isolation barrier is a component in its own right. A gate drive transformer with a high isolation rating is the usual choice, and its interwinding capacitance has to be low or the displacement current returns through the driver.

The plus or minus 30 V window is comfortable for a 10 to 15 V drive. What it does not tolerate is a gate left floating, because at this voltage the leakage from drain to gate is enough to charge a floating gate. A resistor from gate to source at the driver end is a permanent part, not a debug aid.

Where the part fits and where it does not

It fits a 1000 V string switch at a few hundred milliamps, a capacitor bank discharge path, an x-ray or a PMT bias supply, a piezo driver and a high voltage start up circuit. It does not fit a current above about 1 A continuous without a heatsink, a polluted environment without a coat, or a switching converter above 20 kHz where the capacitance loss dominates.

For a part at this voltage the questions are the creepage the enclosure allows, the isolation of the gate drive and the coating on the board. Our strategic sourcing page covers how a single source high voltage part is qualified and held before a build depends on it.

The sourcing side of this part is covered on the obsolete part cross reference hub. For a 1500 V part from a narrow supply, that page covers how a single source code is held and what replaces it.

Questions we get on this code

Can it be used at 1500 V continuously? The rating is 1500 V and the 80 per cent rule points at 1200 V. A 1000 V string at 1100 V open circuit in the cold sits inside that, with a coat and a clamp.

Why only 3 A? Because the die area goes into voltage rather than conductance. At 3 A the loss is 54 W, so the working current is nearer 0.3 to 1 A.

Can a 5 V logic output drive it? No. The threshold is 4.5 V and the resistance is published at 10 V. Use a gate driver with an isolated supply.

What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.