VBM11515
Product Specifications
VBM11515
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM11515 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM11515: 150 V and 12 milliohm in TO-220AB
The VBM11515 is an N channel MOSFET in the TO-220AB body, printed at 150 V drain to source with plus or minus 20 V on the gate. On resistance is 12 milliohm at a 10 V gate and 14 milliohm at 7.5 V, with 80 A at a 25 C case and 70 A at 125 C, and a 120 A pulsed rating over 100 microseconds. The vendor files it under uninterruptible supplies, switch mode supplies, lighting, synchronous rectification, DC to DC converters, motor drive, inverters, solar micro inverters and class D audio.
The 150 V class sits between the 100 V parts used on 48 V rails and the 200 V parts used on 110 V rectified mains, and it is usually chosen for a 72 V battery pack, a 96 V bus or the secondary of a converter that has to survive a 120 V transient. At 12 milliohm the conduction loss at 40 A is 19 W, which the TO-220 tab can move into a heatsink, and the 175 C junction limit gives margin on a hot plate.
The numbers a buyer compares
| Drain to source voltage | 150 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 12 milliohm at 20 A |
| On resistance at 7.5 V gate | 14 milliohm at 20 A |
| Continuous drain current | 80 A at 25 C case, 70 A at 125 C case |
| Pulsed drain current, 100 microsecond | 120 A |
| Single pulse avalanche energy | 150 mJ into 0.1 mH, 45 A |
| Power dissipation | 355 W at 25 C case, 125 W at 125 C case |
| Junction to case | 0.4 C per watt |
| Junction to ambient, one inch board | 40 C per watt |
| Gate threshold voltage | 2 V minimum, 4 V maximum |
| Total gate charge | 63 nC typical, 95 nC maximum |
| Input capacitance | 4425 pF |
| Output capacitance at 75 V | 535 pF |
| Body diode forward voltage | 0.73 V at 30 A, 1.2 V maximum |
| Body diode reverse recovery | 110 ns typical, 220 ns maximum |
Where the sheet and the summary disagree
The product summary prints 60 nC for gate charge and the electrical table prints 63 nC typical against 95 nC maximum. The difference is small but it is real, and it matters in the sense that the summary is not the number to budget a driver against. The 95 nC maximum is the figure a production build should use, because a driver sized on the typical will be marginal on the slowest lot.
The threshold window is 2 V minimum and 4 V maximum, which is wide and worth attention. A 7.5 V drive, which is where the second resistance row is measured, is well clear of the maximum, and a 5 V drive is also clear but with less margin on a cold device. A 4.5 V logic rail is not enough for this part in a hard switched stage, and a customer who plans to drive it from a microcontroller pin should be told so before the board is built.
Reverse recovery is the weak point of this die: 110 ns typical and 220 ns maximum at 30 A with 100 A per microsecond, and a recovered charge of 0.5 to 1 microcoulomb. In a hard switched half bridge at 50 kHz that is a real loss in the opposite switch and a real source of ringing, and it is the reason a 150 V part is often used in a phase shifted or a synchronous stage with a short dead time rather than in a simple bridge. The forward voltage of 0.73 V at 30 A is good, so the diode loss during dead time is modest; it is the recovery that has to be managed.
The turn on rise time of 114 ns typical and 220 ns maximum in the sheet test is slow for a part with 63 nC of gate charge, and it is worth saying that the test is run with a 1 ohm gate resistor into a 1.25 ohm load, which is a soft condition by modern standards, and it reflects the 1 ohm gate resistor and the test load rather than the die. In a real circuit the edge is set by the driver and the external resistor, and the switching loss at 100 kHz will be dominated by the crossover time rather than by the gate charge alone.
Where a 150 V TO-220 part fits
Uninterruptible supplies use it as the battery to DC link switch, where the 150 V rating covers a 96 V pack and the 80 A rating covers a 5 kVA unit at a reasonable duty. Motor drives for 72 V and 96 V traction use it as the low side switch, and the 120 A pulse covers the stall without a larger die. Solar micro inverters and DC to DC converters use it on the high voltage side of a step down stage, and class D audio uses it on a 110 V rail where the 150 V rating leaves room for the audio transient.
The TO-220 body is the practical advantage: it can be bolted to a heatsink with a insulating pad, which no surface mount body does as cheaply. In a 5 kVA uninterruptible supply that is the difference between a 355 W device and a 40 W device, and it explains why this family is still bought in volume while smaller bodies exist.
Sourcing a 150 V part and the matching gate network
The 150 V class is less crowded than 40 V or 100 V, so the second source question is harder and the differences between vendors are larger. Our one stop BOM sourcing approach starts from the whole switching cell rather than the part number: the driver, the gate resistor, the snubber and the current sense are quoted together, because a substitution that changes the gate charge changes the value of the resistor as well.
Where a lead time forces an alternative, the route in component lead time solutions is to qualify a part against the same four rows we use everywhere: threshold maximum, resistance at the gate voltage the driver actually produces, gate charge maximum and diode recovery. For a 150 V part the recovery is the row most likely to spoil a drop in replacement, and the double pulse test in how to verify a drop in replacement is the one that measures it at the real bus voltage.
Questions we are asked about this code
Is 80 A available at 125 C? No: 80 A is at a 25 C case and 70 A at 125 C case, and both assume the tab is held at that temperature. In free air the part is limited by the 40 C per watt path and carries a fraction of that. The second question is whether the 7.5 V resistance row means the part can be driven from a 7.5 V rail. It can, with 14 milliohm instead of 12, and the threshold maximum of 4 V leaves enough margin, but the gate charge is unchanged so the driver still has to deliver 63 nC per cycle.
The third question is about the diode. A 220 ns maximum recovery is slow, and a hard switched bridge will see it. The honest answer is that this part is better in a topology that keeps the body diode out of the conduction path, or with a short dead time and a fast recovery check at the real current. The fourth is avalanche: 150 mJ into 0.1 mH at 45 A covers a motor turn off in most cases, but it is a single pulse and it derates with temperature.
On supply, we quote the reel and the date code, and we sample resistance at 10 V and threshold from each lot. Where a customer needs a matched set for parallel operation, we select from one date code and one wafer lot where the vendor allows it, because at 12 milliohm the threshold spread is the main cause of poor current sharing.