VBL1803
Product Specifications
VBL1803
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1803 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1803: 80 V and 230 A at 3.1 milliohm
The VBL1803 is a single N channel MOSFET in a TO263 body rated at 80 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 230 A of drain current and 3.1 milliohm at a 10 V gate. The die is a trench part, which is the process used at this voltage rather than the charge balance structures of the 600 V and 700 V codes in this band.
This is a different animal from the high voltage parts around it. Eighty volts is the class for a 48 V bus, a 60 V battery string, a 48 V telecom rail and the low side of a 36 V motor drive. At 3.1 milliohm the part is built to carry current, not to hold voltage.
Two hundred and thirty amps through 3.1 milliohm is 164 W, which is arithmetic and not a product. The current column is a die figure at a 25 C case. What the board can carry is set by the copper, the vias and the tab, and on a normal board the answer is a fifth to a quarter of the label.
Key data for the VBL1803
| Configuration | Single N channel |
| Package | TO263, surface mount with the tab on the drain |
| VDS | 80 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V |
| ID | 230 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 3.1 milliohm |
| Technology | Trench |
| Loss at 30 A | 2.8 W at 3.1 milliohm |
| Loss at 60 A | 11.2 W at 3.1 milliohm |
| Loss at 100 A | 31 W at 3.1 milliohm |
| Copper in the loop | A few hundred microohm of trace and via is a tenth of the die resistance at this level |
When the copper is part of the resistance
At 3.1 milliohm the die is no longer the only resistance in the path. A source connection through two vias, a short trace and a connector pin can add 0.2 to 0.5 milliohm, which is ten per cent of the total, and at 60 A that is a few watts in places the thermal model rarely includes. A part selected on the die figure alone can run hotter than the arithmetic predicts because the rest of the loop was left out.
The source inductance of the package is the other half of the same problem. At these currents a fast turn off drives a voltage across that inductance, and the gate loop sees it as a source bounce that can turn the device back on. That is the reason a part like this wants a Kelvin source connection, a tight gate loop and a gate resistor that is chosen for the loop rather than for the data sheet.
Parallel operation is common at this current. Two parts share the current only if their thresholds are close, and the sharing drifts with temperature because the resistance rises with heat. A small source resistor per device is the classic fix, and at 3 milliohm it costs a real fraction of the total, so the resistor is a real cost rather than an addition.
Eighty volts on a 48 V rail.
A 48 V lead acid string reaches 58 V at the top of charge and higher during an equalisation step. A 48 V lithium string at 14 cells reaches 58.8 V. Both sit inside 80 V with room for a clamped transient, and both sit above the 60 V class, which is why 80 V exists as a class at all.
Load dump is the case that breaks the rule. A 48 V automotive rail can see a transient far above the steady state, and 80 V is not the class for an unclamped load dump. Where the product claims an automotive 48 V rail the part sits behind a clamp, and the clamp voltage rather than the nominal rail is what the drain sees.
A 60 V battery system at 16 cells reaches 67 V, which leaves 13 V of margin to 80 V. That is thin for a switching node with a fast turn off, so a snubber or a higher voltage class is the answer depending on how fast the switch has to be.
Threshold at 3 V and a 20 V gate window
A 3 V threshold is a compromise. It is high enough that the part is off at zero gate volts with a pull down of a few tens of kilohm, and low enough that a 4.5 V drive enhances it well enough for most of the resistance to be available. The catalogue prints the resistance at 10 V only, so a 4.5 V drive has to be checked against a curve rather than against a column.
The plus or minus 20 V window is standard at this voltage and it is comfortable for a 10 V drive. On a 48 V rail the gate driver sits at the source of a high side switch, which floats with the switching node, so the driver has to be isolated or bootstrapped and the bootstrap capacitor has to hold up through a long on time.
Gate charge at this die size is substantial. A driver that sources an amp is the normal choice, and the resistor in the gate sets the transition time. A slow transition lowers the drain ringing and raises the switching loss, and at 60 A the balance point is usually a few tens of nanoseconds rather than a few hundred.
Where the part fits and where it does not
It fits the low side of a 48 V motor drive, a battery disconnect on a 60 V string, a synchronous rectifier on a 12 V output supplied from 48 V, a hot swap path at 30 to 60 A and the main switch of a 48 V to 12 V converter. It does not fit an unclamped automotive load dump, a 96 V string, or a load above about 60 A without a copper area built for it.
For a 48 V board the questions are the current the copper can carry, the threshold spread across a lot and the source inductance of the loop. Our one stop BOM sourcing page covers how a group of parts on a rail like this is bought and matched on one order.
The sourcing side of this part is covered on the BOM scrubbing. For a high current part used on several boards, that page covers how the line is cleaned of duplicated codes and wrong suffixes.
Questions we get on this code
Can it carry 230 A? No. That is a die figure. At 100 A the die alone makes 31 W, and the copper adds more. On a good board 40 to 60 A continuous is the realistic range.
Is 3.1 milliohm measured at the pins? No, it is a die figure at a 10 V gate. The package and the board add to it, and at this level that addition is a tenth of the total.
Can two of them be paralleled? Yes, with a source resistor each and a shared gate drive. Threshold spread across a lot is what decides how well they share.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.