Contact Us

VBL1105

Brand: VBsemi
VBsemi VBL1105 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL1105 — Discrete & Power Semiconductors | Superb Automation

VBL1105

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL1105 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL1105: a 100 V, 4 milliohm N channel die in the D2PAK body

The VBL1105 is an N channel trench MOSFET printed at 100 V from drain to source with a plus or minus 20 V gate, in the D2PAK outline that the industry also calls TO-263. The summary gives 4 milliohm at a 10 V gate with 30 A flowing, a continuous drain current of 140 A with the case at 25 C and 87 A with the case at 125 C, a pulsed rating of 440 A and a single avalanche energy of 280 mJ from 0.1 mH. The junction is rated to 175 C, the gate resistance is screened on every part, and the package is described by the vendor as a low thermal resistance body.

This is a die for a heatsink, not for a bare board. At 140 A the conduction loss is 78 W, and at 0.4 C per watt from junction to case the die sits 31 C above the tab. That is a workable number only because the tab is bolted to metal. The junction to ambient figure of 40 C per watt on a one inch board tells the other side of the story: the same 78 W through that path is impossible, and the board level current is closer to 25 A for a 100 C rise.

The ratings a buyer checks first

Drain to source voltage100 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 30 A, 25 C4 milliohm typical
On resistance at 10 V gate, 30 A, 125 C17 milliohm typical
On resistance at 10 V gate, 30 A, 175 C25 milliohm typical
Continuous drain current, case at 25 C and 125 C140 A and 87 A, package limited
Pulsed drain current440 A
Repetitive avalanche current and energy75 A and 280 mJ from 0.1 mH
Power dissipation, case at 25 C and ambient at 25 C375 W and 3.75 W
Junction to case and junction to ambient0.4 and 40 C per watt
Gate threshold at 250 microamp2 V minimum, 4 V maximum
Total gate charge at 50 V and 85 A110 nC typical, 160 nC maximum
Gate source and gate drain charge24 and 24 nC typical
Total gate resistance at 1 MHz1.0 ohm typical, 6.2 ohm maximum
Input, output and reverse transfer capacitance5500, 750 and 280 pF
Turn on delay and rise time20 and 125 ns typical
Turn off delay and fall time55 and 130 ns typical
Body diode forward drop at 85 A1.0 V typical, 1.5 V maximum
Reverse recovery time and charge at 50 A70 ns and 0.19 microcoulomb typical

Reading the electrical table instead of the front page

The resistance spread across temperature is the first thing to write down. Four milliohm becomes 17 milliohm at 125 C and 25 milliohm at 175 C, so a die that dissipates 4 W cold dissipates 25 W hot at the same current. A 100 V part in this body is usually chosen for a 48 V or 72 V bus with a large current, which means the hot row is the operating point and the cold row is a marketing number. A current that produces an acceptable 60 C rise at switch on will produce a 300 C rise once the tab is warm.

The switching rows are slow on purpose. A rise time of 125 ns and a fall time of 130 ns against a 110 nC gate charge describe a large die that cannot be commutated quickly, and a 100 V rail with 440 A of pulse capability is a motor drive or a hot swap, not a 200 kHz converter. In a half bridge at 20 kHz the switching loss is small compared with the conduction loss and the slow edges keep the electromagnetic signature low. In a 100 kHz converter the same edges would dominate the loss budget.

The gate resistance column deserves attention. A typical of 1.0 ohm against a maximum of 6.2 ohm is a wide window, and the vendor screens every part for it, which is the reason the row exists at all. When several of these are paralleled to share 300 A, the gate resistance controls how evenly the current divides during the switching interval, and a 6 ohm part next to a 1 ohm part will take a different share for the length of the edge.

The body diode rows are complete, which is not always the case on a 100 V part. A reverse recovery time of 70 ns and a recovered charge of 0.19 microcoulomb at 50 A are modest figures, and the 1.0 V forward drop at 85 A is what makes the diode usable during dead time. In a motor drive that runs the low side diode for a noticeable part of the cycle, the diode loss is real and should be counted, not waved away as freewheeling.

Where a 100 V D2PAK die earns its place

The first use is a three phase motor drive on a 48 V or 60 V battery, where the 100 V rating covers the regenerative overshoot and the 140 A package current covers the stall condition for a short interval. The D2PAK tab is bolted or clipped to a heatsink, so 78 W at full current is a thermal problem with a known answer: a bigger heatsink or a lower current. In a 1 kW drive at 48 V the phase current is around 20 A, which is 1.6 W per device and well inside the board figure.

The second use is an OR-ing or reverse polarity element on a 48 V bus, where two of these in a redundant supply share the load and the body diode carries the current during switchover. The low forward drop and the complete recovery data matter here, because the diode conducts for the length of the changeover and then hands back to the channel.

The third use is a hot swap or inrush limiter on a 72 V battery pack, where the part has to survive a short circuit for the time it takes the controller to react. The 440 A pulse rating and the 280 mJ avalanche figure describe a die with a large area, and the safe operating area curve is the document to read rather than the two numbers. A 100 V part on a 72 V pack has 28 V of headroom, which is enough for a cable inductance kick and not enough for a lightning surge.

Sourcing notes and the second source question

The D2PAK footprint is standard, but the die inside is not, and the parameters that decide a second source are the hot resistance and the gate charge, not the cold resistance. Two 100 V parts that both print 4 milliohm can differ by 50 per cent at 125 C, which on a 40 A load is the difference between a 27 W and a 40 W loss. The power management cross reference carries the hot rows beside the cold ones for that reason.

The gate resistance screen is a feature worth keeping in the approved part list. A vendor that tests every part and prints a maximum of 6.2 ohm is telling a buyer that paralleling is supported; a vendor that prints only a typical is not. Where several parts share a phase, the pin to pin cross reference keeps the gate and source lead assignment in view, because a part with the gate on a different lead changes the loop inductance on the board.

Availability for a 100 V die in this body follows the industrial and automotive cycles, and the reel is large. A buyer who needs a few hundred parts for a prototype is usually served from a broken reel, and the date code then matters as much as the part number. Our component lead time solutions page covers how we hold stock against a build rather than against a forecast.

Questions we answer before a reel is booked

The first question is the heatsink. A 140 A rating with the case at 25 C is a statement about the mounting, not about the part, and a buyer who plans to run 100 A from a bare board should be told that the board figure is 25 A. We ask for the tab temperature the product can hold, then work back to the current.

The second question is the gate drive. At 160 nC maximum the gate charge needs a driver that can deliver an amp for the length of the edge, and the 24 nC of gate drain charge will couple into the drain node if the gate resistor is too small. A 10 ohm resistor and a 12 V drive are the usual starting point for a motor drive at 20 kHz.

The third question is the diode. In a motor drive the low side diode conducts during dead time and during freewheeling, and the 1.5 V maximum forward drop at 85 A is 85 W for the length of that interval. A buyer who has sized the heatsink on conduction loss alone should add the diode term, especially at low speed where the freewheeling interval is long.