High-Speed Laminate Portfolio
| Material | Dk | Loss Level | Max Data Rate | Typical Use |
| Panasonic Megtron 6 | ~3.7 | Low-Loss | Up to 25 Gbps | PCIe Gen4, 100G Ethernet, mid-range servers |
| Panasonic Megtron 7 | ~3.3 | Ultra-Low-Loss | 112G PAM4 | 800G switches, AI accelerators, 5G backhaul |
| Isola Tachyon 100G | ~3.3 | Ultra-Low-Loss | 112G PAM4 | Data center fabrics, optical transceivers |
| Isola I-Tera MT40 | ~3.4 | Low-Loss | Up to 56 Gbps | 400G line cards, server motherboards |
| Nelco N4000-13 EP | ~3.4 | Low-Loss | Up to 56 Gbps | Backplanes, high-layer-count designs |
Back-Drilling — Stub Removal for Signal Integrity
At data rates of 25 Gbps and above (PCIe Gen4/Gen5, 100G/400G/800G Ethernet, 112G PAM4), the unused portion of a plated through-hole via acts as an unterminated stub — causing signal reflections that degrade the eye diagram and increase bit error rates. Back-drilling removes this stub from the opposite side of the board, leaving only the portion of the via that connects its target layers.
Back-Drill Process Parameters
| Depth Control Accuracy | ±0.05 mm — verified by post-drill inspection on every panel |
| Drill Diameter | Slightly larger than the original via hole to ensure complete stub removal |
| Drill Direction | From the opposite side of the board, stopping a controlled distance from the target signal layer |
| Design Rule | Leave clearance between back-drill holes and adjacent traces to account for the larger drill diameter |
| Applicable Protocols | PCIe Gen4 (16 GT/s), PCIe Gen5 (32 GT/s), 100G Ethernet, 400G/800G Ethernet, 112G PAM4 SerDes |
Differential Impedance Control
High-speed serial links — PCIe, Ethernet, NVLink, DDR memory buses — rely on tightly controlled differential impedance to maintain signal integrity. We model every controlled-impedance stackup in Polar Instruments software before fabrication, adjusting trace width, dielectric thickness, and material Dk to hit the target impedance. TDR (Time Domain Reflectometry) test coupons on every production panel verify the result.
| Target Impedances | 85Ω (PCIe, DDR) and 100Ω (Ethernet, high-speed differential) |
| Standard Tolerance | ±5% |
| Critical Tolerance | ±2% — available for designs requiring tighter control |
| Verification | TDR impedance coupon on every production panel |
| SI Support | Full-link simulation and stackup modeling during DFM review |
High-Layer-Count Capability — 20 to 68 Layers
Data center switches, AI training backplanes, and 800G switch fabrics demand layer counts far beyond standard multilayer PCBs. The increased layer count is driven by the need for multiple high-speed routing layers, dedicated ground references for every signal layer, multiple split power planes, and shielding layers between high-speed regions.
| Layer Range | 20–68 layers for high-speed digital applications |
| Aspect Ratio | Up to 25:1 on thick high-layer-count boards |
| Material | Ultra-low-loss laminates throughout — no FR-4 downgrade on inner layers |
| Registration | Layer-to-layer within ±0.025 – 0.06 mm — X-ray verified on every panel |
| Warpage Control | Symmetrical stackup with low-CTE cores — flatness verified before drilling |
High-Speed Applications
| Data Center Switches | 400G/800G switch fabrics, line cards, backplanes — 48–68 layers, Megtron 7 / Tachyon 100G |
| AI & GPU Accelerators | GPU accelerator cards (20–40L), UBB GPU motherboards (30–68L), NVLink interconnect |
| Optical Transceivers | 100G/400G/800G optical module PCBs — ultra-low-loss, tight impedance, compact form factor |
| 5G Backhaul & Telecom | High-speed baseband processing, OTN framer/mapper boards, SDN/NFV compute nodes |
| Server Motherboards | PCIe Gen5 multi-lane, DDR5 memory, high-speed serial fabrics |
| High-Speed Backplanes | Up to 68-layer chassis backplanes with press-fit connectors and full back-drill |
High-Speed PCB Manufacturing Parameters
| Laminate Portfolio | Megtron 6, Megtron 7, Tachyon 100G, I-Tera MT40, Nelco N4000-13 EP |
| Max Data Rate | 112G PAM4 |
| Layer Count | 20–68 layers (higher on request) |
| Min Trace / Space | 4/4 mil (0.10 mm) typical; 0.035 mm in HDI fan-out zones |
| Back-Drill Accuracy | ±0.05 mm |
| Differential Impedance | 85Ω / 100Ω, ±5% standard (±2% critical) |
| Surface Finishes | ENIG, ENEPIG, Immersion Silver (low-loss RF sections) |
| Test | TDR impedance coupon every panel; flying probe full netlist; AXI (automated X-ray inspection) via barrel sampling |
| Layer Registration | ±0.025 – 0.06 mm |
| Back-Drill Stub | ≤ 0.25 mm (target ≤ 0.1 mm) |
| Single-Ended Impedance | 50Ω |
| Max Lamination Cycles | 7 (including sequential lamination) |
| Min Cavity / Step Width | 2.5 mm |
| Buried Resistor | 50Ω, ±10% |
Send your high-speed PCB requirements to pcba@superb-tech.com for a free DFM review and quotation.