VBGQF1606
Product Specifications
VBGQF1606
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGQF1606 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGQF1606: a 60 V N channel switch in a 3 by 3 millimetre DFN
The VBGQF1606 is an N channel trench MOSFET with a 60 V drain to source rating and a plus or minus 20 V gate, built in the SGT cell and supplied in the eight lead DFN 3 by 3 body. The summary prints 7 milliohm at a 10 V gate with 20 A flowing and 12 milliohm at a 4.5 V gate, a continuous drain current of 50 A with the case at 25 C and 30 A with the case at 100 C, and a pulsed rating of 150 A. The junction is rated to 175 C, the on resistance rows are printed hot as well as cold, and the part is screened 100 per cent for gate resistance.
The package is the part most buyers get wrong. A DFN 3 by 3 has no leads to bend, so the drain pads under the die are the only thermal path, and the junction to ambient figure on a one inch square board is 50 C per watt in steady state against 18 C per watt for a ten second pulse. That pair of numbers describes a package that behaves very differently on a bench and in a sealed enclosure, and it is the reason the 50 A headline needs a case temperature, not an ambient one.
The ratings a buyer checks first
| Drain to source voltage | 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 20 A, 25 C | 7 milliohm typical |
| On resistance at 10 V gate, 20 A, 125 C | 10 milliohm typical |
| On resistance at 10 V gate, 20 A, 175 C | 14 milliohm typical |
| On resistance at 4.5 V gate, 20 A | 12 milliohm typical |
| Continuous drain current, case at 25 C and 100 C | 50 A and 30 A, package limited |
| Pulsed drain current | 150 A |
| Continuous source current through the diode | 85 A |
| Single avalanche energy from 0.1 mH | 125 mJ at 120 A peak |
| Power dissipation, case at 25 C and ambient at 25 C | 136 W and 3 W |
| Junction to case, junction to ambient steady state | 1.1 and 50 C per watt maximum |
| Gate threshold at 250 microamp | 1 V minimum, 2 V typical, 3 V maximum |
| Total gate charge at 30 V and 50 A | 68 nC typical, 70 nC maximum |
| Gate drain charge | 13 nC typical |
| Input, output and reverse transfer capacitance | 5100, 470 and 225 pF |
| Turn on delay and rise time | 11 and 14 ns typical |
| Turn off delay and fall time | 36 and 26 ns typical |
| Body diode forward drop at 20 A | 1.0 V typical, 1.5 V maximum |
Reading the electrical table instead of the front page
Take the headline current first. Fifty amps through 7 milliohm is 17.5 W, and at 1.1 C per watt from junction to case the die sits about 19 C above the case while the case is held at 25 C by something outside the package. Nothing in a normal product holds a DFN tab at 25 C, so the number that decides the board is the 50 C per watt figure. Allowing a 100 C rise from a 60 C ambient, the board can carry about 2 W, which is 17 A through the same 7 milliohm. Everything above 17 A has to be bought with copper, airflow or duty cycle.
The hot rows make the gap wider. At 175 C the same die reads 14 milliohm, twice the cold value, so a load that dissipates 4.5 W at switch on dissipates 9 W once the board has soaked. A 60 V part in a 3 by 3 body is usually asked to do exactly this: sit on a 48 V rail in a small enclosure with no fan, warm up over twenty minutes, and hold a current that was calculated cold. The printed 125 C and 175 C rows are the ones to put in the thermal spread sheet, not the 25 C row.
Switching behaviour is the other half. The gate charge of 68 nC at a 10 V gate and 13 nC of gate drain charge are moderate for a 60 V die, and the 11 ns turn on delay against a 14 ns rise means the part can be clocked at a few hundred kilohertz without the driver working hard. The turn off side is slower at 36 ns delay and 26 ns fall, which is typical of a cell tuned for on resistance rather than for a hard commutation. In a synchronous buck the low side spends most of its time in the third quadrant and switches with the body diode already conducting, so a slow fall costs almost nothing. In a half bridge with a fast high side it costs dead time.
One line is worth reading twice. The threshold window runs from 1 V to 3 V at 250 microamp, and the 4.5 V row is printed at 20 A with a resistance 70 per cent above the 10 V row. A gate driven from a 3.3 V logic pin through a small resistor will sit near the bottom of the overdrive, and the part will still switch, but the resistance will be the 4.5 V value or worse. In a battery product that runs down to 3.0 V, the gate drive has to come from a charge pump or a dedicated driver if the loss budget was written around 7 milliohm.
Where a 60 V DFN part earns its place
The first use is the low side of a synchronous buck that runs from a 24 V or 36 V rail and delivers between 5 A and 15 A. The 60 V rating covers a 36 V input with room for the switch node ringing that a fast high side produces, and the low on resistance keeps the conduction loss small in the long low side interval. The 175 C junction is useful here because the low side runs hot while the high side runs cool, and a part that derates early will limit the output current before the inductor does.
The second use is a load switch or an input protection device on a 48 V rail. A 60 V part leaves about 12 V of headroom over a nominal 48 V bus, which is thin but workable for a battery bus that is regulated, and it is not enough for a telecom bus that carries a 100 V transient. For a 48 V battery pack the part is a reasonable choice; for a 48 V telecom input with lightning surge the next voltage class up is the honest answer.
The third use is a hot swap or inrush element in a line card, where the safe operating area matters more than the on resistance. The single avalanche figure of 125 mJ from 0.1 mH at 120 A peak is a starting point rather than a clamp, and the pulsed current of 150 A against 50 A continuous shows how much the die can take for a short interval. A buyer who plans to use the avalanche rating as a repetitive clamp should ask for the derating curve, because the printed value is a single pulse at 25 C start.
Sourcing notes and the second source question
A DFN 3 by 3 is not a standard footprint in the way a D2PAK is. The eight pads are the same size, the gate can sit on pin 1 or pin 4 depending on the vendor, and two parts that match on voltage, resistance and body size can still be wired differently under the die. The pin to pin cross reference keeps the lead assignment and the pad map in the same row as the electrical data, so a candidate is rejected before a sample is ordered rather than after the first prototype is built.
The resistance rows are where second sources usually fail. Two 60 V parts that both print 7 milliohm at 25 C can differ by a factor of two at 125 C, and a circuit that has been signed off on the cold number will run out of margin in the enclosure. The power management cross reference carries the hot rows beside the cold ones for exactly that reason, and it also flags the parts where the 4.5 V row is missing, because a missing row is not the same as a good one.
Supply is the other half. A 60 V SGT die in a 3 by 3 DFN is a high volume consumer and computing part, so the reel sizes are large and the lead time swings with the handset and server cycles rather than with automotive. Our component lead time solutions page describes how a second source is qualified on a live bill of materials without a full requalification cycle.
Questions we answer before a reel is booked
The first question is whether 4.5 V of gate drive is enough. The threshold window tops out at 3 V, so a worst case part at 4.5 V has 1.5 V of overdrive and the sheet prints 12 milliohm at that gate with 20 A. It works, but a divider or a logic pin with a 1 V drop under load can put the gate near 3.5 V, where the resistance is not specified at all. A charge pump driver is the cheap insurance.
The second question is the board. The steady state junction to ambient figure of 50 C per watt assumes a one inch square pad on FR4 with the drain pads soldered down and no other heat source nearby. In a stacked board or a potted module the real figure is higher, and a 10 A load that looks comfortable on paper can reach 150 C. We ask for the copper area and the ambient before quoting a current, because the same part is a 17 A device on one board and an 8 A device on another.
The third question is incoming inspection. The parameters that drift between lots on a part of this size are the threshold and the on resistance at 4.5 V, so a sample plan should measure both on a few parts per reel at a controlled temperature. The incoming inspection plan we use sets out a workable sample size for a MOSFET reel without turning the goods inwards area into a laboratory.