Contact Us

VBGQA1400

Brand: VBsemi
VBsemi VBGQA1400 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQA1400 — Discrete & Power Semiconductors | Superb Automation

VBGQA1400

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQA1400 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQA1400: a 40 V 250 A switch in the DFN 5 by 6 body

The VBGQA1400 is an N channel trench MOSFET in the DFN 5 by 6 outline, printed at 40 V with plus or minus 20 V on the gate and a 175 C junction. On resistance is 0.8 milliohm at a 10 V gate with 40 A flowing and 0.9 milliohm at 7.5 V, rising to 1.2 milliohm at 125 C and 2.0 milliohm at 175 C at 30 A. Continuous drain current is 250 A with the case at 25 C and 150 A with the case at 100 C, the pulsed rating is 750 A, and single pulse avalanche energy is 134 mJ at 125 A peak from 0.1 mH. Input capacitance is 8800 pF, gate charge 96 nC typical and the body diode forward drop 1 V typical at 20 A.

A 40 V die at 0.8 milliohm is at the state of the art for silicon in a leadless body, and the hot rows printed on this sheet are what make it usable rather than just impressive: the resistance at 175 C is 2.5 times the cold value, and any loss calculation that uses 0.8 milliohm at a 120 C junction is going to be wrong by a factor of two.

The ratings a buyer checks first

Drain to source voltage40 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 40 A, 25 C0.8 milliohm
On resistance at 7.5 V gate, 30 A, 25 C0.9 milliohm
On resistance at 125 C and 175 C, 30 A1.2 and 2.0 milliohm
Continuous drain current, case at 25 C250 A, package limited
Continuous drain current, case at 100 C150 A, package limited
Pulsed drain current and diode pulsed current750 A
Single pulse avalanche energy and current134 mJ from 0.1 mH, 125 A peak
Power dissipation with the case at 25 C136 W
Junction to ambient, ten second and steady state15 to 18 and 40 to 50 C per watt
Junction to case0.85 C per watt typical, 1.1 maximum
Drain leakage at 30 V, 25 C, 125 C and 175 C1 microamp, 50 microamp and 250 microamp maximum
Input, output and reverse transfer capacitance8800, 470 and 225 pF at 40 V
Total gate charge and gate drain charge96 and 15 nC typical, gate source 17 nC
Turn on delay and rise time20 and 15 ns typical
Turn off delay and fall time35 and 20 ns typical
Diode forward drop at 20 A, reverse recovery1 V typical, 1.5 V maximum, 4 ns typical

Reading the electrical table instead of the front page

At 250 A a 0.8 milliohm channel dissipates 50 W, and the junction to case figure of 0.85 C per watt puts the die 42 C above the case. That is a real number for a DFN with a soldered tab and a heavy copper plane, and it is why the 250 A row is marked as package limited: the limit is the eight leads and the tab, not the die. On the steady state ambient row of 40 to 50 C per watt the honest continuous current is about 60 A, where 2.9 W lifts the junction 115 C above a 60 C ambient inside the 175 C limit.

The hot resistance rows change the thermal arithmetic in both places at once: at 175 C the resistance is 2.0 milliohm, so the same 60 A dissipates 7.2 W instead of 2.9 W, which raises the junction further and pushes the budget into thermal run away unless the copper is bigger than a one inch pad. The way out is to size on the 175 C column rather than the 25 C column, and the answer usually comes out at 35 A to 45 A continuous on a real board rather than 60 A.

The avalanche row looks modest at 134 mJ, and it is, but the current is 125 A and the inductance is only 0.1 mH, which is the correct test for a low voltage part: the energy in a 40 V system is small and the current is large. A buyer who reads 134 mJ and compares it with the 1000 mJ of a 100 V part is comparing two different tests, and the row that matters is the peak current a cable or a motor can force through the die.

The switching numbers are fast: 15 ns rise and 20 ns fall with 8800 pF of input capacitance and a 96 nC gate charge means the driver has to deliver amps, not milliamps. That is normal for a die this size, and it is the reason a 40 V 0.8 milliohm part usually comes with a dedicated driver in the same product. The diode recovery of 4 ns typical with a 135 ns maximum is a wide spread; the maximum is the number to plan a dead time around, and a figure that spans thirty times between typical and worst case should be treated as an upper bound rather than a characteristic.

Where a 40 V sub milliohm device earns its place

The first use is the synchronous rectifier in a 12 V output converter, where the duty cycle is short, the current is high and 0.8 milliohm is the difference between 92 per cent and 95 per cent efficiency. The second is a battery protection switch in a 24 V to 36 V pack, where the part sits in the return path and carries the full discharge current for hours.

The third is a motor drive for a cordless tool or a drone at 24 V, where the switching frequency is 20 kHz to 40 kHz, the peak current is hundreds of amps for milliseconds, and the 750 A pulse and 175 C junction are what keep the die alive during a stall. The fourth is a load switch on a 12 V rail in a server, where the part has to survive a hot plug of a large capacitor bank and the avalanche row is the only protection.

What the part is not is a 40 V blocking element in a 36 V product with a 40 V transient. The margin is a single volt and a leadless body has no lead frame inductance to absorb the spike, so a clamp is required rather than optional, and a buyer who wants to skip it should be looking at a 60 V part at twice the resistance.

Sourcing notes and the second source question

For a DFN 5 by 6 the second source question is first a footprint question, because the body is standardized in outline but not in tab area or in the position of the gate lead, and a candidate can look identical and still require a new stencil. The pin to pin cross reference keeps the land pattern and the lead position beside the electrical rows for that check.

The electrical comparison has to be made on the hot rows, not the cold ones, because two 40 V parts that both print 0.8 milliohm at 25 C can print 1.8 and 2.6 milliohm at 175 C. That difference decides the current a board can carry. The power management cross reference carries both temperature columns for that reason.

On supply, a leadless 40 V die is a high runner in the mobile and server markets and is the first part to go short when those markets tighten. Our component shortage forecast page describes how we watch the allocation signals before they reach a distributor list.

Questions we answer before a reel is booked

The first is the current on the real board. The 250 A row is a 25 C case figure that requires a soldered tab on heavy copper and often a heatsink on the back of the board. On a one inch pad the number is closer to 60 A cold and 40 A at a 175 C junction, and a buyer planning more should show the copper.

The second is the gate drive. With 8800 pF of input capacitance and 96 nC of gate charge, only a real driver reaches the 15 ns rise time. A logic pin drives this die in hundreds of nanoseconds and turns the switching loss into the dominant term.

The third is the diode recovery spread. A 4 ns typical against 135 ns maximum means the dead time in a synchronous stage has to be set from the maximum, and a buyer who has set it from the typical will see shoot through on some units at temperature. The safe plan is the maximum plus the driver's own delay, measured on the board.