Contact Us

VBGJ1102N

Brand: VBsemi
VBsemi VBGJ1102N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGJ1102N — Discrete & Power Semiconductors | Superb Automation

VBGJ1102N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGJ1102N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGJ1102N: a 100 V N channel in the SOT-223 body

The VBGJ1102N is an N channel trench MOSFET in the SOT-223 outline, printed at 100 V with plus or minus 20 V on the gate and a 150 C junction. On resistance is 20 milliohm at a 10 V gate with 20 A flowing and 23 milliohm at 4.5 V, continuous drain current is 10 A with the case at 25 C and 9 A with the case at 70 C, and the pulsed rating is 30 A for 100 microseconds. Gate charge is 76 nC typical and single pulse avalanche energy is 550 mJ at 50 A peak from 0.5 mH.

The SOT-223 is the body a buyer chooses when a TO-252 is too tall or too expensive and an SOP-8 cannot carry the current. The tab is the drain and it is wide enough to solder to a copper plane, so the part sits between the two in every sense, including thermal: 1.3 C per watt junction to case against 0.5 for a TO-252 and 0.5 in print for the SOP-8 part that shares this catalogue.

The ratings a buyer checks first

Drain to source voltage100 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 20 A, 25 C20 milliohm maximum
On resistance at 4.5 V gate, 20 A, 25 C23 milliohm
Continuous drain current, case at 25 C10 A
Continuous drain current, case at 70 C9 A
Pulsed drain current for 100 microseconds30 A
Single pulse avalanche energy and current550 mJ from 0.5 mH, 50 A peak
Power dissipation, case at 25 C and 100 C150 W and 57 W
Junction to ambient on a one inch pad, junction to case40 and 1.3 C per watt
Gate threshold voltage at 250 microamp2.5 V minimum, 4.5 V maximum
Drain leakage at 100 V, 25 C, 125 C and 150 C1 microamp, 150 microamp and 5 mA maximum
Input, output and reverse transfer capacitance1500, 246 and 21 pF at 100 V
Total gate charge and gate drain charge76 and 16.9 nC typical, 96 nC maximum
Gate resistance at 1 MHz1.5 to 5 ohm
Turn on delay and rise time11 and 110 ns typical
Turn off delay and fall time35 and 80 ns typical
Body diode reverse recovery and recovered charge35 ns and 0.9 microcoulomb typical

Reading the electrical table instead of the front page

At 10 A and 20 milliohm the conduction loss is 2 W, which against 40 C per watt on a one inch pad is an 80 C rise. From a 25 C ambient that is a 105 C junction and safe; from a 70 C ambient it is 150 C, exactly on the limit, which is where the 9 A row at 70 C case comes from. So the 10 A rating is real only for a board at room temperature with a full one inch pad under the tab, and any enclosure that raises the ambient to 70 C cuts the usable current by a tenth before any derating for the actual copper area is applied.

The gate charge of 76 nC on a 10 A part is large relative to the die, because the test condition reads 60 A of drain current and the input capacitance is 1500 pF. Driving 76 nC at 100 kHz costs 11 mA of average current and about 1.1 W of switching loss at a 10 V gate, so a small SOT-223 switch in a 100 kHz converter spends as much on switching as on conduction. Running it at 30 kHz to 50 kHz is the natural fit, and at those frequencies the 110 ns rise time is a small fraction of the period.

The threshold window from 2.5 V to 4.5 V is the row to read before a logic level drive is chosen. A 5 V rail drives the worst case part with 0.5 V of overdrive, which is not enough to reach the 23 milliohm printed at 4.5 V, and at the hot corner the threshold falls while the transconductance rises, so the part enters linear operation during a switching edge. A 10 V gate is the condition the resistance rows were measured at, and the 4.5 V row is best treated as a fallback for a battery product that runs at 7.4 V nominal.

The body diode is honest for a trench part: 35 ns typical and 70 ns maximum of reverse recovery, 0.9 microcoulomb of recovered charge, and 0.8 V to 1.2 V of forward drop at 10 A. In a boost converter the diode carries the full inductor current during the on time, so 1.2 V at 10 A is 12 W in the diode, which no SOT-223 can survive. In that position the part only works in discontinuous mode at low duty, and a synchronous boost with a second switch is the real answer.

Where a 100 V switch in a small body earns its place

The first use is a reverse blocking or ORing element on a 48 V rail, where the switch has to block 100 V during a transient and carry 5 A to 8 A continuously. The second is the low side switch in a 60 V to 80 V boost or flyback, where the drain sees the reflected voltage plus the leakage spike and a 100 V part with 550 mJ of avalanche energy survives the clamp.

The third is a relay replacement in an industrial product, where a mechanical contact is being swapped for a semiconductor and the board is already laid out for a SOT-223 regulator footprint. The fourth is a battery disconnect in a 12 V to 24 V pack, where the part carries the load current in one direction and blocks the charger in the other, so the body diode is in the path during normal operation and the forward drop matters more than the resistance.

What the part is not is a motor drive switching device. At 10 A continuous and a 30 A pulse for 100 microseconds, a motor start inrush of 30 A lasting a few milliseconds is already outside the rated pulse, and the 550 mJ avalanche figure is a single pulse number rather than a repetitive one. A motor application needs a part with a published repetitive avalanche curve and a bigger pulse window.

Sourcing notes and the second source question

The SOT-223 is the most widely copied package in the catalogue and the least standardized in tab width, so a second source that matches electrically can still fail a solder joint inspection on a board built for a narrower tab. The pin to pin cross reference records the tab and lead dimensions beside the electrical rows, which is the only way to keep that check in one place.

The electrical comparison has to be made at the gate voltage the board actually provides. A 23 milliohm part at 4.5 V and a 20 milliohm part at 10 V are not interchangeable on a 5 V drive, and the power management cross reference keeps the two gate columns separate for exactly this reason. Where the original part has gone long lead, the component lead time solutions page describes the qualification path for a candidate that differs only in gate charge.

Questions we answer before a reel is booked

The first question is whether the 10 A rating survives the enclosure. At 2 W of conduction loss and 40 C per watt the junction sits 80 C above ambient, so a 60 C ambient gives 140 C and a 70 C ambient gives 150 C. A buyer who needs 10 A in a hot box should be looking at a TO-252 part at a third of the resistance, not at a bigger pad.

The second question is the gate drive. A 4.5 V row is printed, but the threshold window reaches 4.5 V, so the resistance at that gate is measured on a part that is barely enhanced. Ten volts is the honest drive and the 76 nC of gate charge is what the driver has to deliver at the switching frequency chosen.

The third question is incoming inspection. On this body the parameters that separate a good lot from a marginal one are the threshold at 250 microamp and the on resistance at 10 V, both of which can be measured with a curve tracer on a sample per reel. The avalanche energy and the reverse recovery are vendor screen items and cannot be repeated at goods inwards, so a certificate is the only evidence available.