VBFB2625
Product Specifications
VBFB2625
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBFB2625 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBFB2625: a minus 60 V P channel switch in the TO-251 body
The VBFB2625 is a P channel trench MOSFET in the TO-251 outline, printed at minus 60 V from drain to source with plus or minus 20 V on the gate. On resistance is 13.5 milliohm at a minus 10 V gate with 50 A flowing and 17 milliohm at minus 4.5 V, continuous drain current is minus 50 A with the case at 25 C and minus 38 A with the case at 125 C, and the pulsed rating is minus 200 A. The junction is rated to 175 C, and the part is printed as 100 per cent gate resistance and UIS tested, which means the avalanche row is a production screen rather than a simulation figure.
The body is the three lead TO-251 with the tab connected to the drain, so the thermal path runs through the tab into copper rather than through the leads. That is why the junction to case figure is 1.1 C per watt while the junction to ambient figure on a one inch pad is 50 C per watt: the copper under the tab is the heatsink, and a part that looks comfortable on the case row can be hot on the board row. On a P channel high side switch there is usually no room for a large tab pad, because the drain node is the switched rail and the copper area is shared with the load.
The ratings a buyer checks first
| Drain to source voltage | minus 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at minus 10 V gate, minus 50 A, 25 C | 13.5 milliohm typical, 26 milliohm at 125 C, 32 milliohm at 175 C |
| On resistance at minus 4.5 V gate, minus 14 A, 25 C | 17 milliohm typical |
| Continuous drain current, case at 25 C | minus 50 A, package limited |
| Continuous drain current, case at 125 C | minus 38 A |
| Pulsed drain current | minus 200 A |
| Single pulse avalanche energy and current | 135 mJ from 0.1 mH, minus 52 A peak |
| Power dissipation, case at 25 C and 125 C | 136 W and 45 W |
| Junction to case, junction to ambient on a one inch pad | 1.1 and 50 C per watt |
| Gate threshold voltage at minus 250 microamp | minus 1.5 V minimum, minus 2.5 V maximum |
| Gate leakage at plus or minus 20 V | plus or minus 100 nA maximum |
| Total gate charge and gate drain charge at minus 10 V | 98 and 21 nC typical, 150 and 32 nC maximum |
| Total gate resistance at 1 MHz | 1.47 milliohm minimum, 2.9 typical, 4.42 maximum |
| Turn on delay and rise time | 15 and 12 ns typical |
| Turn off delay and fall time | 112 and 39 ns typical |
| Body diode forward drop at minus 50 A | minus 0.8 V typical, minus 1.5 V maximum |
| Operating and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The first thing the resistance row gives away is the loss at the headline current. Fifty amps through 13.5 milliohm is 33.8 W, and the junction to case figure of 1.1 C per watt puts the die 37 C above the case with no pad counted. With the case held at 25 C that is inside the 175 C junction, but a case at 25 C means a heatsink or a very large copper plane, and on a one inch pad the same 33.8 W against 50 C per watt is impossible. The realistic continuous figure on a plain board is around 13 A, where the conduction loss is 2.3 W and the pad lifts the junction 115 C above a 60 C ambient. Everything between 13 A and 50 A has to be justified by copper, airflow or duty cycle, not by the ratings page.
The hot resistance rows are printed separately, which most vendor summaries leave out. At 125 C the same die reads 26 milliohm and at 175 C it reads 32 milliohm, so the loss at a fixed current nearly doubles across the range. A 20 A load that dissipates 5.4 W cold dissipates 12.8 W hot, and that second number is the one that decides the pad area. On a P channel switch used as a reverse polarity element in a 24 V product, the thermal run away argument matters more than the nominal resistance, because the part starts cold and ends hot in the same enclosure.
The gate charge is high for a 60 V part: 98 nC typical and 150 nC maximum at a minus 10 V gate, with 32 nC of gate drain charge. Driving that at 100 kHz costs 15 mA of average gate current in the driver and 1.5 W of switching loss at 10 V of gate drive, so the part belongs in a static switch, a slow enable path or a low frequency bridge rather than in a 200 kHz converter. The turn off delay of 112 ns against a 39 ns fall time tells the same story: the die is large and the charge has to come out before the current starts to fall.
One row is missing and it is worth naming. The diode section prints the pulsed current and the forward drop but no reverse recovery time and no recovered charge, so on a bridge leg the behavior of the body diode in the opposite device cannot be read from this sheet. For a high side switch that never conducts in reverse this does not matter. For a half bridge it is the difference between a clean dead time and a shoot through, and a buyer should ask the vendor for the recovery curve rather than assume a symmetric part.
Where a minus 60 V P channel earns its place
The classic use is reverse polarity protection on a 24 V or 48 V input, where the P channel sits in the positive rail with the gate pulled to ground through a resistor and a zener. In that position the part carries the full load current continuously and the gate is held at the rail, so the minus 10 V resistance row applies and the minus 20 V gate limit gives room for a 48 V rail only if the gate is clamped. Without a clamp a 48 V transient will exceed the gate rating, and the part that survives a bench test dies on the first load dump.
The second use is a high side load switch on a battery rail between 12 V and 36 V, where the switch has to block in both directions when off and stay off with the load capacitor charged. A P channel does that without a charge pump, which is why it survives in products where a small BOM matters more than the conduction loss. The third use is a low side switch in an H bridge for a small motor at 24 V, where 175 C junction and 135 mJ of avalanche energy cover the inductive turn off that a 150 C part would not.
What the part is not is a synchronous rectifier. At 60 V and 13.5 milliohm the figure of merit is 810 milliohm nanocoulomb once the gate charge is counted, which is an order of magnitude worse than a modern 30 V N channel. A buyer who needs efficiency at 5 V output should be looking at a lower voltage part, and a buyer who needs 60 V blocking should be looking at whether the topology really forces a P channel.
Sourcing notes and the second source question
A P channel second source is harder than an N channel one for a reason that has nothing to do with the ratings: the pin order of a TO-251 is not standardized across vendors, and a part that matches on voltage, resistance and package can still have the gate on a different lead. The pin to pin cross reference keeps the lead assignment and the tab orientation in the same row as the electrical data, so a candidate is rejected before a sample is ordered rather than after the first prototype.
Where the original part is on allocation, the power management cross reference carries the hot resistance rows beside the cold ones, because two 60 V P channels that both print 13 milliohm at 25 C can differ by a factor of two at 125 C. On a switch that runs warm, that difference is the whole margin.
Supply is the other half of the question. A TO-251 with a 175 C junction and UIS screening is usually a single source product line, and a buyer who has qualified one vendor should keep a second part in the approved list before the shortage rather than during it. Our component lead time solutions page describes how a second source is qualified on a live BOM without a full requalification cycle.
Questions we answer before a reel is booked
The first question is whether minus 4.5 V of gate drive is enough. The threshold window runs from minus 1.5 V to minus 2.5 V, so a worst case part at minus 4.5 V has 2 V of overdrive, and the sheet still prints 17 milliohm at that gate with 14 A flowing. It works, but the resistance is 26 per cent higher than at minus 10 V, and a gate driven through a divider from a 5 V rail will sit closer to minus 4 V than to minus 4.5 V.
The second question is the avalanche figure. 135 mJ from 0.1 mH at minus 52 A is a single pulse rating with the junction at 25 C, and a switch that turns off an inductive load once per cycle accumulates the same energy every time. The 175 C junction helps, but the derating curve has to be read rather than assumed, and a product that switches a relay coil at 10 Hz should be checked against the repetitive curve.
The third question is incoming inspection. On a P channel of this size the parameters that drift between lots are the threshold and the gate leakage, so a sample plan should measure the threshold at minus 250 microamp, the gate leakage at plus or minus 20 V and the on resistance at minus 10 V on a few parts per reel. The avalanche screen the vendor performs is not something a buyer can repeat on the bench, which is why the UIS claim is taken on the certificate rather than on the meter.