Contact Us

VBFB1303

Brand: VBsemi
VBsemi VBFB1303 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBFB1303 — Discrete & Power Semiconductors | Superb Automation

VBFB1303

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBFB1303 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBFB1303: a 30 V N channel at 3.5 milliohm in TO-251

The VBFB1303 is an N channel trench MOSFET in the TO-251 outline, printed at 30 V from drain to source with plus or minus 20 V on the gate, and it is aimed squarely at OR-ing, server rails and DC to DC output stages. On resistance is 0.0035 ohm at a 10 V gate with 38.8 A flowing and 0.0045 ohm at a 4.5 V gate with 37 A. Continuous drain current is 100 A with the case at 25 C, 95 A with the case at 70 C, 35 A on a 10 second pulse with the ambient at 25 C and 26 A at 70 C, and the pulsed rating is 197 A.

The TO-251 body is a through hole tab package with the drain on the tab, which suits a board that still uses a heatsink or a thick copper bar for a 30 A rail. The die is large: 3000 pF of input capacitance, 171 nC of gate charge at a 10 V drive, and a 250 W case dissipation figure that only means something with the tab bolted down. The vendor note adds the detail that matters on a 100 A row: the package limitation current is 90 A.

The ratings a buyer checks first

Drain to source voltage30 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 38.8 A0.0035 ohm typical
On resistance at 4.5 V gate, 37 A0.0045 ohm typical
Continuous drain current, case at 25 C and 70 C100 A and 95 A
Continuous drain current, 10 second pulse, ambient at 25 C and 70 C35 A and 26 A
Pulsed drain current197 A
Avalanche current and energy39 A, 94.8 mJ into 0.1 mH
Package limitation current90 A, stated in the vendor notes
Power dissipation250 W at 25 C case, 3.75 W at 25 C ambient
Junction to ambient, 10 second pulse32 C per watt typical, 40 maximum
Junction to case0.5 C per watt typical, 0.6 maximum
Gate threshold voltage1.0 V minimum, 2.5 V maximum
Total gate charge at 10 V and 4.5 V gate171 and 81.5 nC typical
Input, output and reverse transfer capacitance3000, 710 and 170 pF
Turn on delay and rise time at 10 V gate18 and 11 ns typical
Body diode forward voltage at 22 A0.8 V typical, 1.2 V maximum
Junction and storage rangeminus 55 to plus 175 C

Reading the electrical table instead of the front page

The current rows need sorting before they mean anything. The 100 A figure is a 25 C case calculation and the vendor note says the package limitation is 90 A, so the part cannot carry 100 A even with an ideal heatsink. The 35 A figure is a 10 second pulse at a 25 C ambient and the 26 A is the same pulse at 70 C, which for a TO-251 tab on a heatsink is the realistic envelope. At 35 A the die loses 4.3 W, and the 32 C per watt pulse path takes the junction 137 C above ambient, which is already beyond a 150 C limit from a 25 C start.

That arithmetic says the honest continuous current is lower than the headline by a wide margin. At 20 A the loss is 1.4 W, the junction rise on the 32 C per watt path is 45 C, and a 60 C ambient puts the junction at 105 C, which is comfortable. At 30 A the loss is 3.15 W and the junction sits near 160 C, which is not. A buyer who wants 30 A from this body needs the tab on a heatsink or a copper bar, and should treat the 3.75 W ambient row as the ceiling for a bare board.

The gate charge split between the two drive voltages is the largest in this band: 171 nC at 10 V and 81.5 nC at 4.5 V, with 34 nC of gate source charge and 29 nC of gate drain charge. The 4.5 V column is less than half the charge, which makes a 5 V rail an attractive drive for a load switch even though the resistance rises to 0.0045 ohm. The switching times tell the same story in reverse: at 10 V the rise time is 11 ns, and at 4.5 V it is 180 ns, a factor of sixteen, because the Miller plateau sits just under the 4.5 V rail and the gate crawls through it.

The body diode is good enough for OR-ing. Forward drop is 0.8 V at 22 A and 1.2 V maximum, recovery is 52 ns typical and 78 maximum, and the recovered charge is 70 nanocoulomb typical and 105 maximum. In an OR-ing path the diode conducts until the channel is enhanced, and 0.8 V at 22 A is 17.6 W for that interval, so the gate has to come on quickly; once it does, the 0.0035 ohm channel carries the same current at 1.7 W.

Where a 30 V N channel at 3.5 milliohm in TO-251 earns its place

The first case is an OR-ing path on a 12 V server rail, where two supplies are diode OR-ed through the channels and the 90 A package limit is far above the 20 A to 30 A the rail actually carries. The second is a synchronous buck output stage on a 5 V or 12 V rail, where the 197 A pulse covers the startup and the 710 pF of output capacitance is small enough for a 300 kHz converter. The third is a battery disconnect on a 24 V pack, where two parts in series still give 7 milliohm and the TO-251 tab can be bolted to a chassis.

It is a poor choice for a 5 V drive at high frequency, where the 180 ns rise time at 4.5 V dominates the switching loss, and for a sealed board with no heatsink, where the 3.75 W ambient figure limits continuous current to about 15 A.

Sourcing notes and the second source question

The substitution that fails on this part is the one that matches resistance and forgets the package limit. A competitor body at 0.0035 ohm with a 60 A tab will look identical in a table and will not carry the 90 A that the note on this sheet allows. Our pin to pin cross reference carries the package limitation and the thermal resistance in the same row as the resistance, which is the only way to compare two OR-ing parts honestly.

Where the part is on allocation, component lead time solutions covers the options that keep a 12 V rail in production, including the case where a slightly higher resistance part in the same footprint is the right answer for a six week gap and the case where a second source has to be qualified on the customer's board before either can ship.

Questions we answer before a reel is booked

The first question is whether 100 A is available. It is not; the package note says 90 A and the ambient rows say 35 A on a pulse and about 15 A continuously on a bare board. The second is the gate drive. At 4.5 V the charge is less than half and the switching is sixteen times slower, so a 5 V rail suits a static load switch and a 10 V rail suits a switching stage.

The third question is the diode in an OR-ing path. At 0.8 V and 22 A the diode dissipates 17.6 W until the channel is on, so the enable has to be quick and the two supplies have to come up in an order that does not leave one diode conducting for long. The fourth is the tab: a TO-251 needs a heatsink or a copper bar to reach the current rows, and a board that treats it as a surface mount part will run at the 3.75 W ambient limit.

On supply, the part ships in tubes or on tape by order code, the reflow peak is 260 C, and the date code and moisture level travel on the label. Incoming inspection samples the on resistance at 10 V and 4.5 V, the threshold at 250 microamp, the breakdown at 250 microamp and the diode drop at 22 A, and the gate charge is checked on a sample basis because the 81.5 nC at 4.5 V is what the driver budget depends on.