Contact Us

VBE2605

Brand: VBsemi
VBsemi VBE2605 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE2605 — Discrete & Power Semiconductors | Superb Automation

VBE2605

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE2605 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE2605: a minus 60 V P channel at 4 milliohm in TO-252

The VBE2605 is a P channel trench MOSFET in the TO-252 outline, printed at minus 60 V from drain to source with plus or minus 20 V on the gate. On resistance is 0.004 ohm typical at a minus 10 V gate with 17 A flowing, 0.007 ohm at a 125 C junction with 40 A and 0.008 ohm at 150 C, and 0.010 ohm at a minus 4.5 V gate with 14 A. Continuous drain current is minus 140 A with the case at 25 C against the package limit and minus 130 A with the case at 125 C. The junction to case figure is 0.82 C per watt typical.

Four milliohm at 60 V is a rare combination, and it is what makes this part interesting for a 48 V battery path, a 36 V to 60 V reverse polarity switch or a high current load switch in a storage product. The die is large, the input capacitance is 4950 pF, and the gate charge is 110 nC typical, so the driver and the gate loop have to be taken seriously even though the part looks like a simple high side switch.

The ratings a buyer checks first

Drain to source voltageminus 60 V
Gate to source voltageplus or minus 20 V
On resistance at minus 10 V gate, 17 A, 25 C0.004 ohm typical
On resistance at minus 10 V gate, 40 A, 125 C and 150 C0.007 and 0.008 ohm
On resistance at minus 4.5 V gate, 14 A0.010 ohm typical
Continuous drain current, case at 25 C and 125 Cminus 140 A and minus 130 A
Pulsed drain current as printedminus 125 A
Avalanche current and energyminus 120 A, 125 mJ into 0.1 mH
Power dissipation113 W at 25 C case, 2.5 W at 25 C ambient
Junction to ambient15 C per watt on a 10 second pulse, 40 C per watt steady state
Junction to case0.82 C per watt typical, 1.1 maximum
Gate threshold voltageminus 1.5 V minimum, minus 3 V maximum
On state drain current at 5 V and 10 V gateminus 50 A
Total gate charge at minus 10 V gate and minus 30 V drain110 nC typical, 165 nC maximum
Input, output and reverse transfer capacitance4950, 480 and 405 pF
Turn on delay and rise time15 and 70 ns typical
Body diode forward voltage at 40 Aminus 1 V typical, minus 1.6 V maximum
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

Two rows on this sheet contradict each other and both are printed as they stand. The pulsed drain current is listed at minus 125 A, which is lower than the minus 140 A continuous row above it, and the continuous rows are footnoted as package limited. Physically a pulse cannot be smaller than the continuous rating, so the pulse row is a template row carried over from a smaller body and the package limit is what governs. A buyer should treat minus 125 A as a pulse figure that was not updated, and should size on the thermal rows rather than on either current number.

The second inconsistency is the junction temperature. The continuous current row is headed with a 175 C junction, while the operating range at the bottom of the same table reads minus 55 to plus 150 C. The 150 C figure is the one that should be used, and the 175 C heading belongs to a sibling die. On a part that runs hot this is not a pedantic point: a 175 C assumption allows 25 C more headroom than the part actually has.

Four milliohm at 40 A is 6.4 W, which the DPAK can remove through a good pad, and that is the useful operating region: at 20 A the loss is 1.6 W, at 40 A it is 6.4 W, and at 100 A it is 40 W. The junction to ambient path of 15 C per watt on a 10 second pulse supports 6 W at a 60 C ambient and a 150 C junction, which is 38 A for ten seconds and not for a minute. In the steady state the 40 C per watt row brings that down to about 2.2 W, which is 23 A on a well padded board.

The gate charge is 110 nC typical and 165 nC maximum at a minus 10 V gate, with 19 nC of gate source charge and 28 nC of gate drain charge. The gate drain charge is 28 per cent of the total, which is low for a die of this size and is the row that keeps the switching loss reasonable: turn on delay is 15 ns, rise time 70 ns, turn off delay 175 ns and fall time 175 ns at a 6 ohm gate resistor. The fall time of 175 ns is the slow edge and it belongs to the load switch behaviour of this part, where a slow fall limits the inductive kick of a cable rather than a deliberate inefficiency.

The body diode is the row to look at in a reverse polarity path. Forward drop is minus 1 V typical at 40 A and minus 1.6 V maximum, recovery time 45 ns typical and 70 maximum, and the diode is rated to minus 40 A continuous and minus 80 A pulsed. During the startup ramp before the gate is driven, the diode carries the whole load, and 1 V at 40 A is 40 W for that interval, so the gate drive has to arrive fast or the body diode has to be bypassed.

Where a minus 60 V P channel at 4 milliohm earns its place

The first case is a battery disconnect on a 48 V pack, where a P channel needs no isolated supply and the 60 V rating covers a fully charged pack plus the regeneration overshoot. The second is a reverse polarity path on a 48 V telecom or industrial input, where the 4 milliohm resistance keeps the drop under 0.2 V at 40 A and the body diode is only used for the first milliseconds. The third is a high current load switch on a 36 V rail in a storage or a power tool product, where the 150 C junction and the 15 C per watt pulse path allow a sealed enclosure with 30 A peaks.

It is a poor choice where the gate drive is a 3.3 V pin, because the threshold reaches minus 3 V and the 4.5 V column already costs 2.5 times the resistance of the 10 V column. It is a poor choice in a hot box at high continuous current, since the 2.5 W ambient figure at 25 C is small against the 6.4 W that 40 A produces, and it is a poor choice for a bidirectional switch, where two of these in series double the loss and the gate drive complexity.

Sourcing notes and the second source question

A 60 V P channel at 4 milliohm is a die size game, and second sources rarely match all three of resistance, gate charge and body diode. A substitute with the same resistance but twice the gate charge will switch slower and run hotter in the same package, and one with a smaller die will have a higher forward drop in the reverse polarity path. Our pin to pin cross reference keeps the gate charge, the diode rows and the package in one view, so the comparison is not made on resistance alone.

Where the part is in allocation or the lead time has moved, component lead time solutions covers the options that do not require a board change, including the case where a 60 V part is replaced by a 75 V part at slightly higher resistance and the same outline, and the case where the honest answer is to buy ahead rather than to substitute.

Questions we answer before a reel is booked

The first question is which current rating is real. The continuous rows are package limited, the pulsed row is lower than the continuous row, and the thermal rows are the ones that describe the part, so 20 A continuous and 38 A for ten seconds are the figures to plan with. The second is the junction temperature: 150 C is the operating limit, and the 175 C heading on the current row belongs to another die.

The third question is the gate drive. At minus 4.5 V the resistance is 0.010 ohm, at minus 10 V it is 0.004 ohm, and the gate is rated to plus or minus 20 V, so a 12 V rail with a zener clamp is the usual answer and the 165 nC maximum charge has to be driven by something more than a logic pin. The fourth is the diode: in a reverse polarity path the body diode carries the load at 1 V and 40 A until the channel takes over, and the gate has to be driven from the input rail itself so that it takes over as the rail rises.

On supply, the part is packed on tape with the date code on the label, the reflow peak is 260 C, and the moisture level follows the reel marking. Incoming inspection samples the on resistance at a minus 10 V gate with 17 A, the threshold at 250 microamp, the breakdown at 250 microamp and the body diode drop at 20 A, because the diode drop is the row that decides the startup behaviour of a reverse polarity path and it is the row most often left out of a datasheet comparison.