VBE2317
Product Specifications
VBE2317
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE2317 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE2317: a minus 30 V P channel at 18 milliohm for load switching
The VBE2317 is a P channel trench MOSFET in the TO-252 outline, printed at minus 30 V from drain to source and plus or minus 20 V on the gate, halogen free to IEC 61249-2-21. On resistance is 0.018 ohm typical at a minus 10 V gate with 7 A flowing and 0.025 ohm at a minus 4.5 V gate with 5.6 A, continuous drain current is minus 40 A with the case at 25 C and minus 30 A on a 10 second pulse with the ambient at 25 C, and the pulsed rating is minus 150 A. Gate charge is 13 nC typical at a minus 4.5 V drive, which is the number that makes this part usable from a logic pin.
This is the smaller brother of the 11 milliohm part in the same voltage class, and the difference is not just resistance. The die is smaller, the gate charge is a fifth, and the switching times at a low gate drive are far slower. For a load switch or a battery switch at 3 A to 10 A, the smaller die is the better engineering choice because the gate drive and the leakage matter more than the last few milliohms, and the part is offered with a 100 per cent gate resistance test that matters when several of them sit in parallel.
The ratings a buyer checks first
| Drain to source voltage | minus 30 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at minus 10 V gate, 7 A | 0.018 ohm typical |
| On resistance at minus 4.5 V gate, 5.6 A | 0.025 ohm typical |
| Continuous drain current, case at 25 C and 70 C | minus 40 A and minus 35 A |
| Continuous drain current, 10 second pulse, ambient at 25 C and 70 C | minus 30 A and minus 28 A |
| Pulsed drain current | minus 150 A |
| Power dissipation | 40 W at 25 C case, 2.5 W at 25 C ambient on a pulse |
| Junction to ambient, 10 second pulse | 40 C per watt typical, 50 maximum |
| Junction to foot, steady state | 24 C per watt typical, 30 maximum |
| Gate threshold voltage | minus 1.0 V minimum, minus 2.5 V maximum |
| Total gate charge at minus 10 V and minus 4.5 V gate | 25 and 13 nC typical |
| Input, output and reverse transfer capacitance | 1455, 180 and 145 pF |
| Turn on delay and rise time at minus 10 V gate | 10 and 13 ns typical |
| Body diode forward voltage at 5.6 A | minus 0.71 V typical, minus 1.2 V maximum |
| Reverse recovery time and charge | 22 ns and 17 nanocoulomb typical |
| Junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
The two switching blocks in this sheet are the most useful rows on it. With a minus 10 V gate the turn on delay is 10 ns, the rise time 13 ns, the turn off delay 23 ns and the fall time 9 ns. With a minus 4.5 V gate the same part needs 38 ns to turn on, 89 ns to rise, 22 ns to turn off and 11 ns to fall. The rise time grows by a factor of seven, which is not a driver problem and not a measurement artefact: it is the Miller plateau sitting close to the lower drive voltage, so the gate spends a long time crossing the region where the drain voltage is moving. A board that switches this part at a few kilohertz will not notice; a board that uses it as a pulse width modulated pass element at 100 kHz will notice in the loss.
Forty amps at 0.018 ohm is 28.8 W, and the case rated 40 W figure is not reachable on a DPAK pad. The 10 second pulse row of 40 C per watt typical and 50 maximum is the realistic path: from a 60 C ambient to a 150 C junction that allows 1.8 W, which is 10 A. In the steady state the sheet itself warns that the maximum is 95 C per watt, which brings the same sum down to about 0.9 W and 7 A. A buyer who needs 20 A continuous at 30 V should be looking at the 11 milliohm part on a larger pad, not at this one on a bigger heatsink.
The threshold window of minus 1.0 V to minus 2.5 V is tighter than the larger die, and the leakage reflects it: the zero gate drain current is minus 1 microamp at 25 C and minus 5 microamp at 55 C, where the bigger part reaches minus 250 microamp at 175 C. For a battery product that sits on a shelf, that is the row that decides whether the pack survives a year. The gate source leakage is plus or minus 100 nA at plus or minus 20 V, and the gate resistance is 0.4 ohm typical, 2.0 typical to maximum and 4.0 ohm maximum, with the 100 per cent test in the features list covering exactly that spread.
The body diode is fast for a P channel: minus 0.71 V typical at 5.6 A, 22 ns of reverse recovery and 17 nanocoulomb of recovered charge. In a reverse polarity path that combination keeps the input node from ringing when the channel takes over from the diode, and the 0.71 V figure is low enough that a 5 A startup ramp does not need a bypass diode to survive.
Where a minus 30 V P channel at 18 milliohm earns its place
The first case is a load switch on a 12 V rail in a handheld instrument, where the gate is driven from a 3.3 V logic pin through a small level shift and the 13 nC of gate charge lets a microcontroller pin with a 10 milliamp driver turn the part on in tens of microseconds. The second is a battery switch in a product that ships with the cell installed, where minus 5 microamp of leakage at 55 C is small against a 2000 milliamp hour cell. The third is a reverse polarity path on a 24 V input, where the 20 V gate rating is not enough on its own and a zener across the gate to source is the standard answer.
It is a poor choice for a high current motor path, where 0.018 ohm at 10 A is 1.8 W and the DPAK pad cannot remove it, and for anything that needs to switch at more than a few tens of kilohertz from a low gate drive, because the 89 ns rise time at minus 4.5 V will dominate the switching loss.
Sourcing notes and the second source question
The second source question here turns on the gate drive rather than on the resistance, and the two switching blocks on the sheet are the evidence. A substitute that prints 0.018 ohm at a minus 10 V gate but has a higher Miller charge will be slower at minus 4.5 V, and a board that was built around 13 nC will see more loss without any table row changing. Our power management cross reference keeps the gate charge at both drive voltages in the same view as the resistance, so the comparison is made at the drive the board actually has.
On cost, the honest comparison for a load switch is not the unit price but the sum of the part, the gate resistor, the level shift and the copper area it needs. How to reduce component cost sets out that arithmetic for switching parts, including the case where a slightly larger die removes a level shift and a zener and pays for itself on the first thousand units.
Questions we answer before a reel is booked
The first question is whether 40 A can be carried. It cannot on a DPAK pad; 10 A on a 10 second pulse and about 7 A in the steady state are the realistic figures, and the 40 A row is a case temperature rating. The second is whether the part can be driven from 3.3 V. The threshold reaches minus 2.5 V, so a 3.3 V drive leaves 0.8 V of overdrive and the 0.025 ohm row applies rather than the 0.018 ohm row, which is still usable for a load switch.
The third question is about the diode. At minus 0.71 V and a fast recovery this part is comfortable taking over from its own body diode in a reverse polarity path, and the 20 V gate rating is what has to be protected rather than the diode. The fourth is the pinout on the tape: the TO-252 gate is on the same lead in every body, so a substitution does not move the gate resistor, but the tab thickness does vary between vendors and the solder profile has to be checked.
On supply, the part is halogen free, the reflow peak is 260 C, and the date code and moisture level travel on the label. Incoming inspection samples the on resistance at both gate voltages, the threshold at 250 microamp, the breakdown at 250 microamp and the gate resistance, since the 100 per cent gate resistance test is a vendor claim that has to be confirmed on the lots actually received.