VBA3410
Product Specifications
VBA3410
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA3410 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA3410: two 40 V N channels optimised for high side work
The VBA3410 is a dual N channel MOSFET in the SO-8 body, printed at 40 V drain to source and plus or minus 20 V on the gate, with 100 per cent gate resistance and unclamped inductive switching testing. Each leg is 10 milliohm at a 10 V gate with 10 A flowing and 15 milliohm at 4.5 V with 9 A flowing, and the typical gate charge is 5.9 nC at a 5 V drive, 15 nC at 10 V. Continuous drain current is 12 A with the case at 25 C, 10 A at 70 C, 10 A at a 25 C ambient and 8 A at 70 C, with a 45 A pulsed rating. The vendor states that the part is optimised for high side synchronous rectifier operation and lists notebook processor core high side switching.
A high side switch in a buck converter has to be turned on into a rising switch node and off into a falling one, which is why the gate to drain charge and the gate resistance matter more than the on resistance alone. This part has 2.3 nC of gate to drain charge against 15 nC total at a 10 V drive, a ratio of about one to six, and 1.8 ohm of typical gate resistance. The output capacitance is 175 pF and the reverse transfer capacitance 73 pF, which is low for a 10 milliohm die and is the reason the switch node rings less than the resistance would suggest. The pair is in one body, so a two phase converter puts both high side switches in one placement.
The ratings a buyer checks first
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 10 A | 10 milliohm |
| On resistance at 4.5 V gate, 9 A | 15 milliohm |
| Continuous drain current | 12 A at 25 C case, 10 A at 70 C case |
| Continuous drain current in still air | 10 A at 25 C ambient, 8 A at 70 C ambient |
| Pulsed drain current | 45 A |
| Continuous source to drain diode current | 3.2 A at 25 C case, 1.6 A in still air |
| Single pulse avalanche current | 17 A into 0.1 mH |
| Power dissipation | 4.1 W at 25 C case, 2.1 W at 25 C ambient |
| Junction to ambient, junction to foot | 39 and 25 C per watt typical, 53 and 29 maximum |
| Gate threshold voltage | 1.2 V minimum, 2.5 V maximum |
| Total gate charge at 10 V and 5 V | 15 nC and 5.9 nC typical |
| Input, output and reverse transfer capacitance | 641, 175 and 73 pF |
| Body diode forward voltage at 9 A | 0.8 V typical, 1.2 V maximum |
| Junction and storage range | minus 55 to plus 150 C |
Why the gate charge rows matter more than the resistance
The document publishes the gate charge at a 5 V drive as well as a 10 V drive, which is unusual and useful: 5.9 nC at 5 V against 15 nC at 10 V means the charge curve is steep in the middle, and a driver that only reaches 5 V gets less than half the charge and a slower edge. The switching rows confirm it. At a 4.5 V drive the turn on delay is 16 ns, rise 12 ns, turn off delay 16 ns and fall 10 ns; at 10 V the same rows are 8 ns, 10 ns, 16 ns and 8 ns. The rise time barely changes, which is the signature of a part with low gate to drain charge: the plateau is short and the edge is set by the gate resistor rather than by the drive voltage. That is the behaviour a high side switch wants, because the edge has to be fast enough to cut switching loss and slow enough not to ring the switch node.
The threshold is 1.2 V to 2.5 V at 250 microamp, so a 4.5 V drive has 2 V of overdrive on the worst case die. On a notebook rail the high side gate is driven from a 5 V rail or from a bootstrap at 5 V to 7 V, which lands in the range where this part was characterised. Gate resistance is 0.36 ohm minimum and 3.6 ohm maximum around a 1.8 ohm typical, so the external resistor has to be chosen against the maximum; 2.2 ohm is a common choice and gives a 10 ns edge into the 641 pF input capacitance with a 2 A driver.
Thermal numbers are consistent with a high side switch that runs at a duty cycle rather than continuously. Junction to foot is 25 C per watt typical, so at 10 A with 10 milliohm the die loses 1 W at 100 per cent duty, and at a 30 per cent duty the average loss is 0.3 W, which puts the junction 8 C above the tab. Junction to ambient is 39 C per watt on a 10 second pulse and 53 C per watt maximum, so the 2.1 W ambient dissipation is a 25 C number. A two phase converter with both legs in one body has 0.6 W of combined average loss, which is why this package copes in a thin chassis with a copper pour.
High side switching in small converters and beyond
The stated job is the high side of a notebook processor core converter, where the input is a 19 V or 20 V adapter rail, the output is around 1 V, and the switching frequency is a few hundred kilohertz. At that duty cycle the high side conducts for a short part of each cycle, so the conduction loss is small and the switching loss dominates, which is exactly why the gate to drain charge and the output capacitance were kept low. The 40 V rating covers the 20 V rail with margin for the adapter transient and the switch node overshoot, which on a fast edge can reach twice the input voltage.
Industrial 24 V systems use the same part as the high side of a 24 V to 5 V converter, where the 40 V rating covers a 30 V transient without a clamp. Here the duty cycle is 20 per cent, the current is 3 to 5 A, and the pair can be used as two phases or as a high side and a redundant high side. Battery powered products with a 24 V to 28 V pack use it as a disconnect on the positive rail, where the channel is on continuously and the 10 A ambient rating applies; at 6 A the loss is 0.36 W and the junction is 14 C above ambient, which is comfortable. Remote radio units with a 28 V rail use the pair as a hot swap element, where the 45 A pulse and the 17 A avalanche current cover the inrush and the cable inductance kick.
Sourcing notes and the second source question
A 40 V dual at 10 milliohm with low gate to drain charge is a specific combination, and the candidates that match the resistance often carry twice the gate charge, which turns a cool high side switch into a hot one. Our power management cross reference puts the gate to drain charge and the output capacitance in the same row as the resistance, because those two decide whether an existing driver and snubber still work. The bench sequence in how to verify a drop in replacement covers the tests that matter here: switch node ringing at the real input voltage, the driver's peak current into the new gate charge, and the temperature rise at the duty cycle the product actually runs.
For unmanned aircraft and portable equipment where weight and heat both matter, the same electrical behaviour is what makes a two phase converter fit a small enclosure, and the component route in drone and UAV components covers the documentation a customer needs for those builds. We hold the incoming record for on resistance at both gate voltages and can quote the gate charge curve rather than a single point, which is what a driver setting has to be checked against.
Questions we answer before a reel is booked
Buyers ask whether the 12 A rating is available in a sealed enclosure. It is a 25 C case figure, and the ambient derating gives 10 A at 25 C air with the junction at 150 C, so the practical continuous current in a 60 C box is nearer 6 A per leg at 100 per cent duty and higher at a converter duty cycle. The second question is whether a 4.5 V drive is enough for a high side switch. It works, with 15 milliohm and a 12 ns rise, which is acceptable at 300 kHz; above that the conduction loss at the higher resistance starts to matter and a 10 V bootstrap is the better answer.
On the body diode, the 3.2 A continuous rating with a 0.8 V drop at 9 A is a dead time spec. During the dead time the low side body diode conducts, not the high side, so the relevant row for a high side part is the reverse recovery of the low side device, which is a different part of the bill of materials. Avalanche current is 17 A into 0.1 mH, and although the document does not print an energy figure in the summary we quote the current and let the customer size the clamp rather than presenting a number that is not in the table.
On supply, the reel, the date code and the tape orientation come from the packing list, and the moisture level and floor life are printed on the label. Where a customer needs both legs matched for a two phase stage, we supply from a single date code and can screen the threshold to a customer limit.