Contact Us

VBA3316

Brand: VBsemi
VBsemi VBA3316 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA3316 — Discrete & Power Semiconductors | Superb Automation

VBA3316

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA3316 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA3316: a 30 V dual at 16 milliohm for system power rails

The VBA3316 is a dual N channel MOSFET in the SO-8 body, printed at 30 V drain to source and plus or minus 20 V on the gate, with 100 per cent gate resistance and unclamped inductive switching testing and compliance to the RoHS directive. Each leg is 16 milliohm at a 10 V gate with 8 A flowing and 20 milliohm at 4.5 V with 5 A flowing, and the typical gate charge is 7.1 nC at 4.5 V or 14.5 nC at 10 V. Continuous drain current is 8.5 A with the case at 25 C, 7.5 A at 70 C, 7.2 A at a 25 C ambient and 5.9 A at 70 C, the pulsed rating is 30 A, and the source diode is 2.8 A at a 25 C case. The vendor lists notebook system power and low current DC to DC conversion.

The die is modest: 660 pF of input capacitance, 140 pF of output capacitance, 86 pF of reverse transfer capacitance and 2.6 ohm of gate resistance. The dissipation is 3.1 W at a 25 C case and 2.0 W at a 25 C ambient, with 52 C per watt junction to ambient on a 10 second pulse and 62.5 C per watt maximum, and 30 C per watt junction to foot. Those are the numbers of a part intended for switching a rail on and off rather than for carrying the main converter current: at 3 A and 16 milliohm the leg loses 0.14 W, and at 6 A it loses 0.58 W, which is inside the ambient ceiling but not far inside it.

The ratings a buyer checks first

Drain to source voltage30 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 8 A16 milliohm
On resistance at 4.5 V gate, 5 A20 milliohm
Continuous drain current8.5 A at 25 C case, 7.5 A at 70 C case
Continuous drain current in still air7.2 A at 25 C ambient, 5.9 A at 70 C ambient
Pulsed drain current30 A
Continuous source to drain diode current2.8 A at 25 C case, 1.8 A in still air
Single pulse avalanche energy5 mJ, avalanche current 10 A into 0.1 mH
Power dissipation3.1 W at 25 C case, 2.0 W at 25 C ambient
Junction to ambient, junction to foot52 and 30 C per watt typical, 62.5 and 40 maximum
Gate threshold voltage1.2 V minimum, 2.5 V maximum
Total gate charge at 10 V and 4.5 V14.5 nC and 7.1 nC typical
Input, output and reverse transfer capacitance660, 140 and 86 pF
Body diode forward voltage at 2 A0.77 V typical, 1.1 V maximum
Junction and storage rangeminus 55 to plus 150 C

Two drive points, two very different parts

At a 10 V drive the switching rows are 7 ns turn on delay, 10 ns rise, 15 ns turn off delay and 7 ns fall. At 4.5 V the same rows are 14, 45, 18 and 12 ns. The rise time is the one that moves: 45 ns against 10 ns is a four and a half fold difference, and on a 30 V rail with a 140 pF output capacitance that is the difference between a converter that runs cool and one that does not. A 4.5 V drive also raises the resistance by 25 per cent, from 16 to 20 milliohm, so the part at a low drive voltage is worse on both counts. This is a 10 V gate part in a system that offers 4.5 V only as a convenience.

The threshold window is 1.2 V to 2.5 V at 250 microamp, so a 4.5 V drive is enough to turn the part on with 2 V of overdrive on a worst case die, and a 3.3 V drive gives 0.8 V, which is marginal. Gate charge of 7.1 nC at 4.5 V is small enough for a controller pin through a 100 ohm resistor at low frequency, and the 2.7 nC gate to drain charge means the plateau is short at a 15 V drain. Gate resistance is 0.5 ohm to 5.2 ohm, a wide window, so the external resistor should be picked with the maximum in mind rather than the typical. The 86 pF reverse transfer capacitance is high relative to the 660 pF input, which is normal for a small die and is why a fast drain edge couples into the gate more than the capacitance ratio suggests.

Thermal data is the binding constraint. At 52 C per watt typical, 5 A per leg with 20 milliohm loses 0.5 W and puts the junction 26 C above ambient; both legs at that current lose 1 W and put the shared lead frame 52 C above ambient, which in a 60 C box reaches 112 C. The 2.0 W ambient figure is a 25 C ambient number and corresponds to a 104 C rise, so the package is near its limit at 1 W in a warm enclosure. A board that switches 8 A per leg in a thin notebook has a copper pour under the tabs and a fan nearby, which is the only way the 8.5 A case rating is reachable.

System power switching rather than main conversion

The natural job is to switch a 12 V or 19 V rail into a subsystem: a display, a fan, a wireless module or a hard disk. In that role the part is on for long periods and switches rarely, so the resistance matters and the switching loss does not. At 3 A with 16 milliohm the drop is 48 mV and the loss is 0.14 W, which is small enough that two legs on one rail do not heat the package. The 30 A pulse covers the inrush into the decoupling bank of the subsystem, and the 5 mJ avalanche rating is enough for a small inductive load and not enough for a motor, which needs a clamp.

The second job is the low current DC to DC conversion the vendor names. A 12 V to 5 V buck at 200 kHz with 2 A output uses one leg as the high side and one as the low side, and at that current the resistance is not the issue; the 10 ns rise at a 10 V drive and the 15 ns turn off delay are. A converter built this way will be about 88 to 90 per cent efficient, which is normal for a small discrete stage and behind an integrated converter with a synchronous rectifier. The third job is a level shifter or a gate clamp on a 24 V relay, where the pair gives two independent switches in one placement and the 20 V gate rating allows a 15 V zener clamp on each gate.

Sourcing notes and the second source question

A 30 V dual at 16 to 20 milliohm is a crowded segment, and the differences that matter are the gate charge, the reverse transfer capacitance and the threshold window. Our pin to pin cross reference compares the legs one at a time, because a candidate can match on the first leg and not the second, and the BOM consolidation view shows where one dual replaces two singles and where the shared thermal path argues against it.

On a product with a long life, the part also has to be checked for the rail it switches. Equipment that carries a medical approval needs the incoming record and the traceability that goes with it, and the route in medical device components covers the lot control and the documentation a customer has to keep. We hold the on resistance sample at both gate voltages and the threshold record per lot, and where a customer needs a specific window we screen against a limit rather than shipping the general population.

Questions we answer before a reel is booked

The first question is whether the 8.5 A rating can be used with a 4.5 V gate drive. It cannot be used that way with any margin: at 4.5 V the resistance is 20 milliohm and the rise time is 45 ns, so both the conduction loss and the switching loss are worse, and 8.5 A at 20 milliohm is 1.45 W per leg, close to the 2 W ambient ceiling with nothing left for the second leg. The second question is whether the two legs can be paralleled for a 12 A switch. They can, with a matched gate resistor, but the threshold windows differ by up to 1.3 V across the population, so the sharing in the linear region is uneven and the inrush has to be shaped by the gate network.

On the body diode, 2.8 A at a 25 C case with a 0.77 V typical drop means the diode carries dead time current and nothing more. A synchronous stage that relies on it for a long dead time at 5 A will put 3.9 W into a package that sheds 2 W in still air. Avalanche is 5 mJ into 0.1 mH, which is a small number, so a relay coil or a solenoid on the same rail needs an external diode and the part should not be asked to absorb the kick.

On supply, the reel and the tape orientation follow the standard SO-8 outline and the date code is on the label. For a build that runs this part alongside a driver and a set of passives, we quote the whole kit from one date code so a first article and a production lot behave the same way on the bench.