Contact Us

VBA3222

Brand: VBsemi
VBsemi VBA3222 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA3222 — Discrete & Power Semiconductors | Superb Automation

VBA3222

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA3222 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA3222: two 20 V N channels at 19 milliohm with a small gate charge

The VBA3222 is a dual N channel MOSFET in the SO-8 body, printed at 20 V drain to source and plus or minus 12 V on the gate, halogen free to IEC 61249-2-21 and carrying 100 per cent gate resistance testing. Each leg is 19 milliohm at a 4.5 V gate with 7.1 A flowing and 26 milliohm at 2.5 V with 6.0 A flowing, and the typical gate charge is 9.5 nC at the 4.5 V point. Continuous drain current is 7.1 A with the ambient at 25 C and 5.7 A at 70 C, the pulsed rating is 40 A over a 10 microsecond width, and the source diode is rated 1.7 A. Power dissipation is 2 W at a 25 C ambient and 1.3 W at 70 C, with 62.5 C per watt junction to ambient.

The document carries no application list, so the placement has to come from the numbers rather than from a vendor label. What the numbers say is a pair of small switches for a low voltage rail: 20 V of blocking, a threshold window of 0.6 V to 1.5 V, 9.5 nC of gate charge and 2 W of dissipation in still air. That combination fits a 5 V or 12 V rail with a load of a few amps per leg, driven directly from a controller pin, on a board where two part numbers were replaced by one. It does not fit a converter that switches hard above 200 kHz with several amps per leg, because the 2 W ceiling arrives before the current rating does.

The ratings a buyer checks first

Drain to source voltage20 V
Gate to source voltageplus or minus 12 V
On resistance at 4.5 V gate, 7.1 A19 milliohm
On resistance at 2.5 V gate, 6.0 A26 milliohm
Continuous drain current in still air7.1 A at 25 C ambient, 5.7 A at 70 C ambient
Pulsed drain current, 10 microsecond40 A
Continuous source current, diode1.7 A
Power dissipation2.0 W at 25 C ambient, 1.3 W at 70 C ambient
Junction to ambient62.5 C per watt
Gate threshold voltage0.6 V minimum, 1.5 V maximum
Total gate charge at 4.5 V9.5 nC
Gate to source and gate to drain charge1.5 nC and 2.5 nC
Gate resistance1.6 to 2.7 ohm
Turn on delay, rise, turn off delay, fall10, 15, 38 and 25 ns typical
Body diode forward voltage at 1.7 A1.2 V maximum
Junction and storage rangeminus 55 to plus 150 C

What the shortened table tells a buyer

The specifications stop earlier than on the larger parts in this band. There is no capacitance row, no avalanche rating, no junction to foot figure and no switching row at a 10 V drive, only the 4.5 V set. A buyer who needs an avalanche rating for an inductive load therefore has to look elsewhere, and a buyer who needs the output capacitance for a resonant converter has to ask for the curve set rather than read a number. What is present is enough to make a decision on a resistive or capacitive load: 19 milliohm at the drive voltage most controllers deliver, a threshold window that a 3.3 V pin can reach, and a gate charge small enough that a 100 ohm series resistor still gives a 15 ns rise.

The switching row was measured at 10 V with a 10 ohm load, 1 A and a 10 ohm gate resistor, which is a deliberately slow setup. The 10 ns turn on delay and 15 ns rise are therefore not the fastest the die can do, and the 38 ns turn off delay with a 25 ns fall is dominated by the gate resistor rather than by the silicon. A board that drives the same part through 10 ohm sees edges about four times faster, and with 1.7 A of source diode current the reverse recovery of 26 ns is short enough that a low side synchronous use in a 5 V converter does not need a parallel Schottky. The single 1.2 V maximum body diode voltage is the one row that limits the diode: at 1.7 A it is 2 W, which is the entire ambient dissipation of the package, so the diode is a transient path and not a load path.

Thermal behaviour sets the practical current. At 62.5 C per watt, a leg running 4 A with 19 milliohm loses 0.30 W, and two legs together lose 0.61 W, which puts the junctions 38 C above ambient. In a 50 C enclosure that is an 88 C junction and comfortable; at 70 C ambient the same load reaches 108 C, still inside the rating but with the second leg heated by the first. The 2 W figure is the stated ceiling at 25 C ambient, and it corresponds to a 125 C rise, so anything above 1 W in a warm box has to be checked rather than assumed.

Where a small dual belongs

The first pattern is two independent load switches on one low voltage rail, one for a sensor board and one for a radio module, each with its own gate signal from the controller. Neither current is large, both benefit from the low threshold, and the 9.5 nC gate charge means the controller pin can drive the gate through a resistor with no driver at all. The second pattern is a single load switch with the two legs in parallel, which halves the resistance to about 9.5 milliohm and doubles the dissipation ceiling, at the cost of a threshold mismatch between the two dies of up to 0.9 V across the window, so the sharing in the linear region has to be forced with a matched gate resistor.

The third pattern is a small half bridge for a 3.3 V to 5 V boost or a 5 V to 3.3 V buck running at a few hundred kilohertz with 1 A or less. Here the 20 V rating covers the ringing at the switch node with room, the 40 A pulse covers the inrush, and the 15 ns rise at a moderate gate resistor keeps the switching loss low. A 12 V rail is the practical ceiling, because the gate rating is plus or minus 12 V and a 12 V rail used as the drive sits exactly at the limit with no allowance for overshoot.

Sourcing notes and the second source question

Because the document is short, a second source comparison on this part cannot rely on matching a headline number. The rows that decide compatibility are the threshold window, the gate charge and the body diode voltage, and the last of those is often missing from a competitor summary. Our power management cross reference keeps those three beside the resistance so a candidate can be judged on behaviour rather than on the front page, and the availability view in lead time solutions shows which of the candidates is actually shippable when the original code is on allocation.

For a customer building a new product, the OEM procurement route is the one that keeps a dual part from becoming a schedule risk: the same date code, the same reel size, and a second source qualified on the bench before the first production run rather than after. We hold incoming records for on resistance at both gate voltages and for threshold, and where a customer needs the capacitance curve set we request it against the order instead of quoting figures that are not in the document.

Questions we answer before a reel is booked

Buyers ask whether 7.1 A is available on a board with no copper pour. At 62.5 C per watt and 19 milliohm, 7.1 A dissipates 0.96 W per leg, which is a 60 C rise and lands the junction at 85 C in a 25 C room. That is inside the rating but leaves nothing for a warm enclosure, and the honest continuous figure for a two layer board in a 60 C box is about 3 A per leg. The second question is whether the 20 V rating can be used on a 12 V rail with a transient. The rating is a hard number, and a 12 V rail with a 15 V load dump transient is beyond it, so the part belongs on a 5 V rail or on a 12 V rail that is clamped.

The gate question is the one that surprises people on this die: the threshold is as low as 0.6 V, so an unconnected gate turns the leg on, and the 12 V gate rating leaves no margin on a 12 V system. Both facts point the same way, a pull down on every gate and a divider or a driver on anything above a 5 V rail. On the body diode, the 1.7 A rating with a 1.2 V maximum drop means the diode is for dead time and not for load, and a converter that relies on it during a long dead time will heat the package past its ambient limit.

On supply we quote the reel, the date code and the tape orientation from the packing list. Prototype quantities come from a cut reel with the same date code as the production booking where the schedule allows, which is the usual way to avoid a re qualification on a part that was approved at first article.