VBA1405
Product Specifications
VBA1405
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA1405 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA1405: 3.8 milliohm at 40 V in an SO-8
The VBA1405 is a single N channel MOSFET in the SO-8 body, printed at 40 V drain to source and plus or minus 20 V on the gate, with 3.8 milliohm at a 10 V gate and 5.7 milliohm at 4.5 V. It carries 18 A at a 25 C case, 13.5 A at 70 C, 12 A at a 25 C ambient and 9.6 A at 70 C, with 50 A pulsed and a 20 mJ avalanche rating at 20 A. The vendor lists notebook CPU core high side switch as the application, and 3.8 milliohm at 40 V is a die that would have needed a much larger package a decade ago.
The part is halogen free, tested for gate resistance and for unclamped inductive switching on every unit, and compliant to the RoHS directive. For a 40 V part at this resistance the UIS test is not a formality: the die is large, the avalanche capability is finite at 20 mJ, and a part that fails the test would fail on the first cable unplug in the field.
The ratings and the conditions behind them
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 3.8 milliohm at 10 A |
| On resistance at 4.5 V gate | 5.7 milliohm at 7 A |
| Continuous drain current | 18 A at 25 C case, 12 A at 25 C ambient |
| Continuous drain current at 70 C | 13.5 A at the case, 9.6 A in ambient |
| Pulsed drain current | 50 A |
| Continuous source current, diode | 4.5 A at 25 C case, 2.2 A at 25 C ambient |
| Single pulse avalanche energy | 20 mJ into 0.1 mH at 20 A |
| Power dissipation | 5 W at 25 C case, 2.5 W at 25 C ambient |
| Junction to ambient, 10 second pulse | 38 C per watt typical, 50 maximum |
| Junction to ambient, steady state | 85 C per watt maximum |
| Junction to foot, drain | 20 C per watt typical, 25 maximum |
| Gate threshold voltage | 1.0 V minimum, 3.0 V maximum |
| Total gate charge at 10 V | 18 nC typical, 27 nC maximum |
| Body diode reverse recovery | fast, with 2.4 nC of gate to source charge quoted |
Reading the table the way a board sees it
The threshold window is 1.0 V to 3.0 V at 250 microamp, and the gate charge is 18 nC typical and 27 nC maximum at 10 V with 2.3 nC of gate to drain charge. A 27 nC maximum on a 3.8 milliohm die is a good figure of merit and the reason the part can switch at 500 kHz without a large driver. The input capacitance is 985 pF, output 205 pF and reverse transfer 76 pF, all at 15 V, and the gate resistance window of 0.3 to 2.6 ohm is wide enough that the external resistor should be chosen on the slowest part rather than on the typical.
The resistance moves with temperature, and the table makes that plain: the 3.8 milliohm is a 25 C figure at a 10 A test current, and a die this size at 125 C is roughly 1.6 times that, which is 6 milliohm. At 10 A the conduction loss rises from 0.38 W to 0.6 W across that range, and at 18 A from 1.2 W to 2 W. A product that runs continuously at 18 A needs the ambient rating of 12 A and the 2.5 W dissipation figure rather than the 25 C case headline.
Switching times are given for a 4.5 V drive and a 10 V drive. At 4.5 V the turn on delay is 14 ns, rise 12 ns, turn off delay 19 ns and fall 9 ns; at 10 V the turn on delay falls to 8 ns and the turn off delay to 16 ns. The fall time is shorter than the rise time in both cases, which is typical of a die with a low internal gate resistance: the turn off is not slowed by the gate network, so the external resistor and the source inductance set the edge. A board with a long source return slows the turn on and rings on the turn off, which is the pattern to look for when a board passes at low current and fails at full load.
The body diode is the limit during dead time. Continuous diode current is 4.5 A at a 25 C case and 2.2 A at a 25 C ambient, and the forward voltage is 0.77 V typical at 2.6 A. In a synchronous buck at 10 A inductor current the diode carries the full current during dead time, so a controller with a 50 ns dead time at 500 kHz dissipates about 0.5 W in the diode on average, which is affordable; a 200 ns dead time quadruples it and heats the die.
Where this part is used
A 12 V to 1.8 V or 1.2 V POL converter at 15 A is the natural socket: the high side switch carries the input current for 15 per cent of the period, and 3.8 milliohm keeps its conduction loss under 0.5 W. The second use is a synchronous rectifier on the secondary of an isolated converter with a 24 V output, where the 40 V rating covers the ringing and the low resistance keeps the loss down at 15 A. The third is a battery disconnect on a 24 V pack, where the part sits in the path and its low resistance keeps the drop under 60 mV at 15 A.
In a motor drive the part works as the low side of a small three phase bridge, and the 50 A pulse covers the stall current. The 20 mJ avalanche rating then sets the limit on how much cable inductance can be switched without a clamp. A handheld tool with a short cable is inside the rating; a pump with a two metre cable is not, and the answer is a clamp or a higher rated part rather than a bigger heat sink.
Sourcing notes and the second source question
A 40 V part at 3.8 milliohm is often replaced when the original goes short, and the comparison has to be made at the drive voltage, not at the headline. Our pin to pin cross reference starts from the pad and the pin map, then compares on resistance at 4.5 V and at 10 V, gate charge and diode recovery, because a substitute that matches at 10 V can be 40 per cent worse at 4.5 V.
Lead time on this class moves with the notebook and server market, and a part that is in stock today can be on allocation next quarter. The routes and the trade offs are set out in component lead time solutions, which covers qualifying a second source before the shortage, holding a buffer against a known build plan, and the case where a slightly higher resistance part is acceptable if the duty cycle is low. We quote this code with the reel size and date code, and we can hold a reserved quantity against a scheduled build.
Questions we answer before a reel is booked
The first question is whether 18 A can be held. It can at a 25 C case, and the ambient rating is 12 A at 25 C and 9.6 A at 70 C, with 2.5 W of dissipation in still air. The second is whether the part works from a 5 V gate drive. It does, at 5.7 milliohm, which is 50 per cent more than at 10 V, and in a high side socket with a 15 per cent duty cycle the total conduction loss rises by less than 8 per cent.
The third question is about the diode. The 4.5 A rating is a dead time figure, not the channel rating, and a converter running in discontinuous mode at light load reverses the role: the diode then carries the inductor current for a real part of the period, and the 2.2 A ambient figure becomes the limit. The fourth is avalanche: 20 mJ at 20 A is a single pulse at 25 C, and a hot board has less headroom than the number suggests.
On supply, this code is a catalogue item with the date code on the reel label. We hold an incoming record with an on resistance sample at 4.5 V and a UIS sample where the vendor provides one, because a re marked lot of a low resistance part shows up as a high resistance at temperature rather than at room temperature.