VBA1307
Product Specifications
VBA1307
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA1307 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA1307: 9 milliohm at 30 V in an SO-8
The VBA1307 is a single N channel MOSFET in the SO-8 body, printed at 30 V and plus or minus 20 V on the gate, with 9 milliohm at a 10 V gate and 11 milliohm at 4.5 V. It carries 13 A at a 25 C case, 12 A at 70 C, 12 A at a 25 C ambient and 10.5 A at 70 C, with 45 A pulsed and a 24 mJ single pulse avalanche rating at 22 A. The vendor summary marks it as optimised for high side synchronous rectifier operation, the same role as its 8 milliohm sibling, and the two differ by one milliohm at a 10 V gate and by nothing at 4.5 V.
That last point is worth stating plainly, because it decides which of the two a buyer should stock. At 4.5 V both parts are 11 milliohm, so a board that drives from a 5 V rail gets the same conduction loss from either. At 10 V the 1210 is 8 milliohm against 9 here, an 11 per cent difference, which only matters in a converter with a high duty cycle or a very low output voltage.
Ratings and their test conditions
| Drain to source voltage | 30 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 9 milliohm at 11 A |
| On resistance at 4.5 V gate | 11 milliohm at 10 A |
| Continuous drain current | 13 A at 25 C case, 12 A at 25 C ambient |
| Continuous drain current at 70 C | 12 A at the case, 10.5 A in ambient |
| Pulsed drain current | 45 A |
| Continuous source current, diode | 3.8 A at 25 C case, 2.1 A at 25 C ambient |
| Single pulse avalanche energy | 24 mJ into 0.1 mH at 22 A |
| Power dissipation | 4.0 W at 25 C case, 2.4 W at 25 C ambient |
| Junction to ambient, 10 second pulse | 38 C per watt typical, 50 maximum |
| Junction to ambient, steady state | 85 C per watt maximum |
| Gate threshold voltage | 1.0 V minimum, 3.0 V maximum |
| Total gate charge at 10 V | 15 nC typical, 23 nC maximum |
| Input capacitance | 1750 pF |
| Body diode forward voltage | 0.8 V typical, 1.2 V maximum |
Reading the rows rather than the front page
The threshold window of 1.0 V to 3.0 V is the first row to check in a low voltage system. On a 3.3 V rail driving the gate directly, the gate to source voltage is 3.3 V, which is only 0.3 V above the maximum threshold, so the worst case die is barely on and its resistance is far above the 11 milliohm in the table. A 5 V rail gives 2 V of overdrive and is the minimum honest drive, and a 10 V rail is what the 9 milliohm row assumes.
Gate charge is 15 nC typical and 23 nC maximum at 10 V, with 2.3 nC of gate to drain charge, and the input capacitance is 1750 pF with 195 pF of output capacitance and 73 pF of reverse transfer. The Miller ratio of 73 pF against 1750 pF is low, which means the drain node does not feed back strongly into the gate and the part is easy to keep stable with a single gate resistor. The gate resistance window of 0.36 to 3.6 ohm is a 10 to 1 spread, and that is the number to check on a build that runs above 500 kHz, because the fastest parts ring with the same external resistor that keeps the slowest ones cool.
Switching times are given twice. With a 4.5 V drive the turn on delay is 16 ns, rise 12 ns, turn off delay 16 ns and fall 10 ns; with 10 V the delays fall to 8 ns and 16 ns and the rise to 10 ns. Turn off delay is longer than turn on delay in both cases, which is normal for a die with a low gate resistance: the gate discharges quickly but the drain current has to commutate against the inductor before the drain voltage moves. At 500 kHz with a 30 per cent duty cycle the total switching time is a small part of the period, and the loss is dominated by the gate charge and the output capacitance rather than by the crossover.
The thermal rows are 38 C per watt for a 10 second pulse and 85 C per watt in the steady state on a one inch square board, with 4.0 W of dissipation at a 25 C case. In a real product the ambient figure of 2.4 W is the one that applies, and at 12 A with 9 milliohm the conduction loss alone is 1.3 W, which leaves the part at 110 degrees above ambient in still air. That is why a 13 A rating in this body is a pulse rating in practice, and why a converter that runs at 12 A continuously needs the copper area or a fan.
Where the part is used
Notebook and tablet buck converters are the listed application and the natural one: a 2 to 3 cell pack, a 1 to 2 MHz switching frequency, and a high side switch that carries the input current for a third of the period. The second use is a POL converter on a 12 V or 24 V rail, where the 30 V rating is comfortable on 12 V and tight on 24 V, and the third is a battery disconnect or a load switch where the low resistance keeps the drop small at 10 A.
In a motor drive the part works as a low side switch, and the 45 A pulse covers the stall current of a small brushed motor. The 24 mJ avalanche rating then matters, because a motor is an inductor and every switch off is an avalanche event unless there is a clamp. At 22 A and 0.1 mH the rating covers a short cable; a long cable or a larger motor needs a diode or a higher rated part.
Sourcing notes and the second source question
Because this part and its 8 milliohm sibling are interchangeable at 4.5 V, a customer can qualify both and take whichever is available, which is a useful hedge against a lead time move. The comparison still has to be made on the rows that change with the drive voltage, and our power management cross reference is built to show them side by side at the voltage on the board rather than at the vendor headline.
When two codes share a reel position and a pad, the risk is a mixed shipment rather than a wrong part, and the control for that is the date code. The process in date code management covers the labelling, the incoming check that the codes match the order, and the rule that a build with a mixed lot is either re qualified or rejected before it starts. We quote this code with the reel size and the date code on the label, and we can hold a single lot against a scheduled build where the quantity allows.
Questions we answer before a reel is booked
Buyers ask what the difference is against the 8 milliohm part. At 4.5 V, nothing that a board can measure; at 10 V, one milliohm, which is 11 per cent of the conduction loss and matters only in a converter with a duty cycle above 50 per cent. The second question is whether 13 A is continuous. It is a 25 C case figure, and the ambient rating is 12 A at 25 C and 10.5 A at 70 C, with the 2.4 W dissipation figure setting the ceiling.
The third question is whether the part can be used on a 24 V rail. It can as long as the rail is clamped, because a 30 V rating leaves 6 V of headroom and a switching node rings above the input on every cycle. A 40 V part is the safer choice for a 24 V system with a long input cable. The fourth is the diode: 3.8 A at a 25 C case is the dead time rating, not the channel rating, and a controller with a long dead time should be checked against it.
On supply, this code is a catalogue item, and we hold an incoming record with an on resistance sample at 4.5 V and a visual check on the lead finish. Where a build needs a specific date code window, the booking has to be made before the order is placed.