VBA1154N
Product Specifications
VBA1154N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA1154N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA1154N: a 150 V N channel in an SO-8 for primary side switching
The VBA1154N is a single N channel MOSFET in the SO-8 body, printed at 150 V drain to source and plus or minus 20 V on the gate. The vendor summary gives 40 milliohm at a 10 V gate and 35 milliohm at 8 V, with 7.7 A at a 25 C case, 6.1 A at 70 C, 5.5 A at a 25 C ambient and 4.5 A at 70 C. The listed application is primary side switch, and the feature list names an extremely low gate to drain charge for switching losses, which is the specification that matters in a flyback or a forward converter running at 100 kHz or more.
The part is halogen free to IEC 61249-2-21, tested for gate resistance and for avalanche on every unit, and compliant to the RoHS directive. For a 150 V part in an SO-8 that is a serious set of tests: the avalanche test screens the parts that would fail on the leakage spike of a transformer primary, and the gate resistance test narrows the spread that otherwise shows up as ringing on the drain node of every unit built with a different reel.
Ratings and the conditions behind them
| Drain to source voltage | 150 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 40 milliohm at 5 A |
| On resistance at 8 V gate | 35 milliohm at 5 A |
| Continuous drain current | 7.7 A at 25 C case, 5.5 A at 25 C ambient |
| Pulsed drain current | 50 A |
| Continuous source current, diode | 4.5 A at 25 C case, 2.6 A at 25 C ambient |
| Single pulse avalanche energy | 20 mJ into 0.1 mH at 20 A |
| Power dissipation | 5.9 W at 25 C case, 3.1 W at 25 C ambient |
| Junction to ambient, 10 second pulse | 33 C per watt typical, 40 maximum |
| Junction to ambient, steady state | 80 C per watt maximum |
| Junction to foot, drain | 17 C per watt typical, 21 maximum |
| Gate threshold voltage | 2.0 V minimum, 4.0 V maximum |
| Total gate charge at 10 V | 28.5 nC typical, 43 nC maximum |
| Body diode reverse recovery | 63 ns typical, 95 ns maximum |
Reading the rows rather than the front page
The first thing to notice is that the summary prints 40 milliohm at 10 V and 35 milliohm at 8 V, which says the lower gate voltage has the lower resistance. That is the opposite of the normal behaviour and it cannot be true for one die. The electrical table repeats the same pair, so the error is consistent across the document rather than a typo on the cover, and the honest reading is that one of the two rows is mislabelled. A buyer comparing this part against another should measure the resistance at the gate voltage the circuit actually uses rather than trust either row, and we state that plainly instead of picking the better number.
The threshold window is 2.0 V minimum and 4.0 V maximum at 250 microamp. For a 150 V part that is normal, and it means a 4.5 V drive sits exactly at the top of the window on a worst case die. A 10 V drive is the right choice, and a 12 V auxiliary rail is better. The gate charge of 28.5 nC typical and 43 nC maximum at 10 V, with 8 nC of gate to source and 6.5 nC of gate to drain charge, is a moderate load, and the low gate to drain charge is what keeps the drain node from spending long in the Miller plateau, which is where most switching loss happens in a flyback.
Switching times are given twice, once at a 10 V drive and once at 8 V. With 10 V the turn on delay is 14 ns, rise 12 ns, turn off delay 22 ns and fall 6 ns; with 8 V the turn on delay grows to 16 ns and the turn off delay falls to 20 ns, while the fall time rises to 7 ns. Those small differences hide a larger effect on loss, because the crossover time during which the drain voltage and the drain current overlap is what heats the die. At 100 kHz with a 50 ns crossover the switching loss per event is a few watt, and at 300 kHz it triples.
The body diode is slow for this class: 63 ns typical and 95 ns maximum recovery with 110 nC of recovered charge at a 100 A per microsecond slope. In a flyback the diode only conducts during the leakage inductance spike, which is short, so the recovery loss is small. In a bridge or an active clamp circuit the diode carries current for a real dead time, and the 110 nC then becomes a loss in the opposite switch that has to be counted. Continuous diode current is 4.5 A at a 25 C case and 2.6 A at a 25 C ambient, both well below the 7.7 A channel rating.
Where a 150 V SO-8 is the right part
A flyback converter running from a 90 to 264 V mains input with a 400 V bus and a 12 V output sees roughly 100 V on the primary switch plus the leakage spike, and a 150 V part gives the margin. The SO-8 body keeps the height low for a wall adapter, and the 5.5 A ambient rating covers a 45 W adapter at 70 C ambient with a modest heatsink through the copper. The second use is a forward converter or an active clamp in a telecom module, where the 150 V rating suits a 48 V input with a 100 V clamp.
LED drivers on a 110 V or 230 V input use the same body as the main switch, and the 20 mJ avalanche rating covers the ringing of a long LED string cable at switch off. Battery powered equipment with a 96 V pack uses the part as a disconnect, where the 150 V rating covers a fully charged pack plus the regeneration transient, and the 4.5 A diode rating covers the inrush into the bulk capacitor through the body diode when the switch is first closed.
Sourcing notes and the second source question
High voltage MOSFETs are usually replaced because the original went obsolete rather than because a cheaper part appeared, and the comparison has to include the gate charge and the diode recovery as well as the on resistance. Our power management cross reference keeps the table to the rows that change behaviour in a switching cell: threshold maximum, on resistance at the drive voltage, total gate charge, gate to drain charge and reverse recovery charge.
When the original code is short and the build is running, the route is often a shortage recovery rather than a new part: a broker with a traceable lot, a date code window and an incoming curve trace on a sample. The options and the risks are set out in BOM shortage recovery, which covers the difference between a lot with a full trace and a lot with a label only. We supply this code with the matching gate resistor and snubber values from the customer bill of materials, and we can quote a matched pair from the same date code where the build needs it.
Questions we answer before a reel is booked
The first question is about the resistance rows. We say what the document says and we say that the two rows cannot both describe one die; a customer who needs the number should measure it on a sample at the gate voltage the circuit uses. The second is whether 7.7 A can be held continuously in a wall adapter. It cannot: that is a case temperature figure, and the ambient rating is 5.5 A at 25 C and 4.5 A at 70 C, with the copper area under the drain pads doing most of the work.
The third question concerns avalanche. The 20 mJ figure is a single pulse into 0.1 mH at 20 A, with the junction starting at 25 C. A flyback that runs at 70 C ambient has far less headroom, and a snubber is the cheaper answer than a part with a larger rating. The fourth is the diode recovery of 95 ns maximum: fine in a flyback, marginal in a bridge, and the customer should measure it in the actual circuit rather than rely on the typical figure.
On supply, this code ships on the standard SO-8 reel with the date code on the label. We hold the incoming record for each lot, including an on resistance sample and a gate charge check on a sample, because a counterfeit or a re marked lot of a 150 V part is the failure we see most often in this class, and it shows up as a low breakdown voltage rather than as a high resistance.