VB7638
Product Specifications
VB7638
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB7638 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB7638: a 60 V N channel in a TSOP-6
The VB7638 is a single N channel MOSFET in the TSOP-6 body, printed at 60 V drain to source and plus or minus 20 V on the gate, with 30 milliohm at a 10 V gate and 35 milliohm at 4.5 V. It carries 7 A at a 25 C case and 4 A at 125 C, with 29 A pulsed and a 5 mJ single pulse avalanche rating. The six lead body puts the drain on four pins, which is the reason a part this small can hold 7 A at all: the current spreads across four leads and the heat leaves through them and through the lead frame rather than through one narrow leg.
The vendor states 100 per cent gate resistance and unclamped inductive switching testing on every unit, and a 175 C junction limit. For a 60 V part in a body this size that is a useful combination, because the usual failure mode in a small package is not the die but the assembly, and a UIS test at final test screens the parts that would fail on the first inductive event in the field.
The ratings and their conditions
| Drain to source voltage | 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 30 milliohm at 5 A |
| On resistance at 4.5 V gate | 35 milliohm at 4 A |
| On resistance at 125 C | 50 milliohm at 5 A |
| On resistance at 175 C | 70 milliohm at 5 A |
| Continuous drain current | 7 A at 25 C case, 4 A at 125 C case |
| Pulsed drain current | 29 A |
| Continuous source current, diode | 6 A |
| Single pulse avalanche energy | 5 mJ into 0.1 mH at 10 A |
| Power dissipation | 5 W at 25 C case, 1.6 W at 125 C case |
| Junction to ambient | 110 C per watt |
| Junction to foot, drain | 30 C per watt |
| Gate threshold voltage | 1.0 V minimum, 2.5 V maximum |
| Total gate charge | 7.6 nC typical, 12 nC maximum |
| Body diode forward voltage | 0.75 V typical, 1.2 V maximum at 1.6 A |
What the electrical table adds to the summary
The resistance rows carry three temperatures and they move a long way: 30 milliohm at 25 C, 50 milliohm at 125 C and 70 milliohm at 175 C, at the same 5 A test current. That is 1.7 times and 2.3 times the cold figure, so a conduction loss budget written from the front page is optimistic by a factor of two in a warm enclosure. The threshold window of 1.0 V to 2.5 V at 250 microamp means a 4.5 V drive turns the part on hard even on a worst case die, and a 3.3 V drive works with less margin but still works.
Gate charge is 7.6 nC typical and 12 nC maximum at a 4.5 V drive, with 2.1 nC of gate to source and 4.1 nC of gate to drain charge. The Miller charge is a little over half the total, which is the signature of a die with a modest drift region and a small gate area: the part switches fast and needs a driver that can hold the plateau without ringing. Input capacitance is 560 pF typical and 700 pF maximum, output capacitance 85 pF and reverse transfer 55 pF, all measured at 30 V.
Switching times are 9 ns turn on delay, 12 ns rise, 19 ns turn off delay and 7 ns fall, into a 7.5 ohm load with a 10 V drive and a 1 ohm gate resistor. The fall time is shorter than the rise time, which is unusual and comes from the low gate resistance window of 1.2 to 3.6 ohm: the turn off path is not current limited by the internal gate resistor, so the external resistor sets the edge. Gate resistance spread across that 3 to 1 window is worth checking on any build that runs above 500 kHz, because the fastest parts ring and the slowest ones heat.
The leakage rows are 1 microamp at 25 C, 50 microamp at 125 C and 150 microamp at 175 C, and the diode forward voltage is 0.75 V typical at 1.6 A. In a synchronous stage the diode carries current during dead time, and at 4 A with a 0.9 V drop that is 3.6 W of instantaneous loss during the dead time window. A dead time of 20 ns at 300 kHz is 0.6 per cent of the period, which keeps the average loss small, but a controller with a long dead time and no body diode conduction limit will heat this part quickly.
Where a 60 V TSOP-6 fits
The first use is a 48 V telecom rail, where the 60 V rating covers the 57 V maximum of a PoE type 4 port and leaves room for the inductive kick of a cable. The six lead body is small enough for a powered device that has to fit inside a lamp housing or a camera dome, and the 110 C per watt junction to ambient sets the practical current at around 1 A in still air. The second use is a 24 V industrial input, where the part works as a reverse polarity pass element or as a load switch behind a connector.
Battery powered tools with a 36 V or 48 V pack use the part as the low side of a small brushless drive, and the 5 mJ avalanche rating covers the switch off transient of a short motor cable. The 4 A rating at a 125 C case is the number to use there, not the 7 A front page figure, because a tool in a sealed housing reaches 125 C case on a warm day. In a 12 V system the part is over specified on voltage and the choice is driven by the small body and the tested avalanche rather than by the 60 V rating.
Sourcing notes and the second source question
The TSOP-6 pinout is less standardised than the SO-8, and two parts with the same six leads can put the drain on a different set of pins. That is the first thing to check before a substitute is offered, because a reversed drain and source turns a load switch into a short across the supply. Our pin to pin cross reference starts from the pin map and the pad geometry, then compares gate charge and threshold, and only then the headline ratings.
Because the vendor tests every unit for gate resistance and unclamped inductive switching, the incoming inspection for this code can be lighter than for an untested part, but it should not be skipped. The plan in incoming inspection plan covers the sample size, the on resistance check at 4.5 V and the solderability check that catches a oxidised lead frame before it reaches the line. We supply this code on the standard reel with the date code on the label, and we hold the vendor test record for each lot where the customer asks for it.
Questions we answer before a reel is booked
Buyers ask whether the 7 A figure can be used in a 48 V PoE device. It can be used as a pulse, not as a continuous current: with 110 C per watt junction to ambient on a one inch board, 1 A continuous already raises the junction by 60 degrees above ambient at 30 milliohm, and a sealed housing adds another 20 degrees. The second question is whether the part survives a cable unplug. The 5 mJ rating covers a short cable at 10 A; a long cable stores more energy and needs a clamp or a higher rated part.
The third question is about the 6 A diode rating, which is close to the 7 A channel rating and higher than the 4 A at a 125 C case. That is not a contradiction: the diode is rated at a 25 C case and the channel rating at a 125 C case is limited by the package. A synchronous stage that runs the diode during dead time should check the 6 A figure against its own case temperature rather than against 7 A.
On supply, this code is a catalogue item and the reel carries the date code. We hold an incoming record with an on resistance sample at 4.5 V and a visual check on the lead finish, and where a customer needs a specific date code for a qualified build, the booking has to be made before the order is placed rather than after the parts arrive.