VB1330
Product Specifications
VB1330
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB1330 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB1330: a 30 V N channel in a SOT-23 that carries 6.5 A
The VB1330 is a single N channel MOSFET in the SOT-23 body, printed at 30 V drain to source and plus or minus 20 V on the gate, with 30 milliohm at a 10 V gate and 33 milliohm at 4.5 V. It carries 6.5 A at a 25 C case, 6.0 A at 70 C case, 5.3 A at a 25 C ambient and 5.0 A at 70 C ambient, and the sheet marks the case figure as package limited, which is the honest way to say that the die is not the constraint. The vendor lists DC to DC conversion as the application, and a 30 V, 30 milliohm part in a three lead body is exactly that: a small switch for a 12 V or 24 V rail, a load switch, or a level shifting gate in a low side drive.
The part is halogen free, compliant to the RoHS directive, and tested for gate resistance on every unit. That last point matters more than it sounds: gate resistance spread is the reason two reels of the same code behave differently in a fast node, and a 100 per cent test on Rg narrows the spread before the parts reach a board.
The ratings that matter at this size
| Drain to source voltage | 30 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 30 milliohm at 3.2 A |
| On resistance at 4.5 V gate | 33 milliohm at 2.8 A |
| Continuous drain current | 6.5 A at 25 C case, 5.3 A at 25 C ambient |
| Pulsed drain current | 25 A |
| Continuous source current, diode | 1.4 A at 25 C case, 0.9 A at 25 C ambient |
| Power dissipation | 1.7 W at 25 C case, 1.1 W at 25 C ambient |
| Junction to ambient, 5 second pulse | 90 C per watt typical, 115 maximum |
| Junction to ambient, steady state | 130 C per watt maximum |
| Junction to foot, drain | 60 C per watt typical, 75 maximum |
| Gate threshold voltage | 0.7 V minimum, 1.1 V typical, 2.0 V maximum |
| Total gate charge at 10 V | 4.5 nC typical, 6.7 nC maximum |
| Input capacitance | 335 pF |
| Body diode reverse recovery | 10 ns typical, 20 ns maximum |
Reading the table the way a board sees it
The threshold window of 0.7 V to 2.0 V is wide for a 30 V part, and it is the first thing to check in a 2.5 V or 3.3 V system. A 3.3 V logic pin driving the gate directly gives a gate to source voltage of 3.3 V, which is above the 2.0 V maximum threshold and therefore turns on even the worst die, but not by much: at 2.8 A the on resistance at 4.5 V is already 33 milliohm and at 3.3 V it is higher, so the loss rises faster than the current does. A 10 V drive is the right choice wherever a rail is available.
Gate charge is 4.5 nC typical and 6.7 nC maximum at 10 V, with 2.1 nC of gate to source and 0.85 nC of gate to drain charge. That is a small load: a microcontroller pin through a 10 ohm resistor switches it in tens of nanoseconds, and a dedicated driver is not needed below 200 kHz. The switching times are given twice for exactly this reason, once with a 4.5 V drive and once with 10 V. At 4.5 V the fall time is 22 ns typical and 35 ns maximum against 5 ns and 10 ns at 10 V, so the low drive not only raises conduction loss, it also slows the edge and increases the overlap loss.
The thermal side is where a SOT-23 surprises people. Junction to ambient is 90 C per watt for a 5 second pulse and 130 C per watt in the steady state, so 1.1 W at a 25 C ambient raises the junction by nearly 120 degrees and lands at the edge of the 150 C limit. A 2 A load at 33 milliohm dissipates 132 mW and is comfortable; a 4 A load at the same resistance dissipates 528 mW and needs either a larger copper area on the drain lead or a lower duty cycle. The 6.5 A figure is a case temperature rating with an ideal heat path, and no SOT-23 on a normal board reaches it.
The body diode is 1.4 A at a 25 C case, well below the 6.5 A channel rating, and reverse recovery is 10 ns typical with 5 nC of recovered charge. In a small synchronous buck at 500 kHz that is a manageable loss; in a converter above 1 MHz the diode conduction during dead time becomes the dominant term and the part should be replaced by one with a shorter recovery.
Where this body earns its place
A 12 V rail switching a 1 A load is the classic use: a solenoid, a relay coil, a small fan or an LED string. The part also works as a low side switch in a battery powered instrument where the load is switched at a low duty cycle, and the 25 A pulse rating covers the inrush of a capacitive load without an oversized device. In a 24 V system the 30 V rating is tight, and a 40 V or 60 V part is the safer choice once a transient is considered.
The second use is as a level shifting gate in a two stage drive, where a small N channel pulls down the gate of a larger P channel or of an IGBT. In that role the 335 pF input capacitance and the 4.5 nC gate charge are the reason to pick this part over a larger one: the logic pin sees almost nothing, and the gate resistance test guarantees that the pull down edge is repeatable from lot to lot.
Sourcing notes and the second source question
The SOT-23 N channel is the most second sourced body in the industry, and the differences that matter are rarely on the front page. Threshold maximum, on resistance at 4.5 V and gate charge decide whether a substitute behaves the same in a fast loop; package lead frame and die attach decide whether it survives the same thermal cycle. Our power management cross reference puts those rows side by side, and the first column we fill is the gate voltage the customer actually has, not the one in the vendor summary.
Lead time on small signal MOSFETs moves with consumer demand rather than with the industrial market, and a 30 V SOT-23 can go from stock to twenty weeks in one quarter. The options and the trade offs are set out in component lead time solutions, which covers qualifying a second body, buying a buffer stock against a known build plan, and the case where a slightly larger package solves both the schedule and the thermal margin. We quote this code with the reel size and date code, and we can hold a reserved quantity against a scheduled build.
Questions buyers ask us about this part
The first is whether 6.5 A is real. It is a case temperature figure, and in still air the part carries about 1 A before the junction reaches 150 C; the ambient rows of 5.3 A and 5.0 A assume a one inch square copper pad on FR4 with a 5 second pulse, which is not the same as a product in a sealed box. The second is whether the part can be driven from a 3.3 V microcontroller. It can, but the on resistance at 3.3 V is well above the 33 milliohm at 4.5 V, and the rise and fall times roughly double, so the loss budget has to use the lower gate voltage.
The third question concerns the body diode rating of 1.4 A. A load that is switched off into an inductive path forces the current through that diode, and 1.4 A is the ceiling at a 25 C case. A relay coil or a small motor with no clamp will exceed it on the first switch off, so a flyback diode belongs on the board rather than in the hope that the MOSFET survives.
On supply, the part ships on the standard SOT-23 reel with the quantity and date code on the label, and the incoming record includes a sample on resistance check at 4.5 V and a gate resistance check. Where a build needs a tighter threshold window than the sheet guarantees, that is a selection step rather than a purchase order note, and it has to be agreed before the reels are booked.