HXNM40010
Product Specifications
HXNM40010
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXNM40010 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXNM40010: twenty eight decibels of gain from 5.3 to 5.9 GHz
The HXNM40010 is a gallium nitride internally matched power amplifier module from Hisiwell. The vendor describes it as built on in-plane matching synthesis with thin film hybrid integration, with 50 ohm input and output impedance at both ports. That last line is the practical one: a 50 ohm part needs no external matching network on the bench, and a first article can be measured with two connectors and a bias tee rather than with a tuned fixture.
The index row reads 5.3 to 5.9 GHz, saturation output at least 33 dBm, gain at least 28 dB, drain efficiency at least 30 per cent, 28 V drain rail, continuous wave, flatness not printed. 33 dBm is 2.0 W of radio frequency from a small module, which is modest power, and 28 dB of gain is high for this class. Those two figures together describe a specific job rather than a general purpose part.
28 dB of gain means the drive for rated output is 5 dBm, which is 3.2 mW. A part that reaches its ceiling on three milliwatts is a driver, not a final stage. It is the block that takes a modulator output or a low level oscillator and lifts it to the level a 20 W or 50 W stage expects, and it does so without a second gain block behind it. In a chain that already has a 33 dBm driver, this part would be redundant; in a chain built around a 5 dBm exciter, it removes a stage.
The 600 MHz window is 10.71 per cent fractional at a 5.6 GHz centre, which is wide for an internally matched module and narrow compared with a broadband discrete. It covers the full 5.8 GHz ISM allocation, the 5.47 to 5.725 GHz band used for fixed wireless, and the lower part of the C band satellite downlink. One part therefore serves several channel plans, which is the reason to accept the matching loss that a wide module carries against a narrow tuned stage.
The parameter rows Hisiwell publishes for HXNM40010
| Part class | Gallium nitride internally matched power amplifier module |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 5.3 to 5.9 GHz |
| Bandwidth, calculated | 600 MHz, 10.71 per cent fractional at a 5.6 GHz centre |
| Saturation output power as published | at least 33 dBm |
| Saturation output power in watts, calculated | 2.00 W |
| Output at 1 dB compression as published | not published, the index prints a slash in that column |
| Gain as published | at least 28 dB |
| Drain efficiency as published | at least 30 per cent |
| Drain voltage | 28 V |
| Input and output impedance | 50 ohm, matched |
| Flatness across the band | not published |
| Operating mode | continuous wave |
| Drive power for the rated output, calculated | 5 dBm, 3.2 mW |
| DC input at saturation, calculated | 6.65 W |
| Drain current at saturation, calculated | 238 mA at 28 V |
| Dissipation at saturation, calculated | 4.66 W |
| Dissipation if efficiency reaches 60 per cent, calculated | 1.33 W |
| Output per 100 MHz of the band, calculated | 0.333 W |
| Load voltage at saturation into 50 ohm, calculated | 9.99 V RMS, 14.13 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour on the same band at 38 dBm with 18 dB gain | HXNM40009, 5.1 to 5.9 GHz |
What a 5 dBm drive point does to the rest of the chain
A 5 dBm drive level means the stage in front of this part does not need to be a power stage at all. A packaged gain block, a mixer with a few milliwatts of output, or an exciter board that already carries its own level control can feed it. The saving is not only current. It is the parts count, the bias networks and the screening that a second power stage would have brought with it.
The catch is that 28 dB of gain in one module is also 28 dB of gain that has to be stable. The vendor publishes no gain flatness and no input return loss figure for this part, so the shape of the response across 5.3 to 5.9 GHz has to be measured on the first article. A module of this class typically moves two to three decibels across a band this wide, and a system with a tight automatic level control loop needs to know where the peaks sit rather than the average.
Gain that high also sets the input power ceiling. The 33 dBm output with 28 dB of gain implies compression at 5 dBm of drive, so an overdrive of six decibels puts the part eleven decibels into compression rather than three. An exciter with a 10 dBm maximum output and no attenuator in front of this module is a part that fails on the first power sweep. Put a fixed pad or a level detector in the path and the margin becomes predictable.
The 28 V rail is a second constraint that reaches back into the supply. At 238 mA of drain current the module draws little, but the bias network still has to survive a 28 V transient and the sequencer still has to apply gate bias before drain. The vendor publishes no quiescent current and no gate voltage window, so the bias point has to be found on the bench and written down, because the next build will not have the same sample on it.
Where 5.3 to 5.9 GHz sits in a real product
The band covers the 5.8 GHz ISM allocation used for industrial links, wireless video and some telemetry systems, the 5.47 to 5.725 GHz fixed wireless band, and the upper part of the 5 GHz WLAN allocation. It also reaches the C band satellite downlink window near 5.9 GHz, which is why parts on this band turn up in satellite news gathering and in ground station receivers that need a transmit path as well as a receive path.
In a wireless video product the module is the last stage before the antenna when the required output is around two watts. A two watt link with a directional antenna covers several kilometres line of sight, and 5.8 GHz keeps the antenna small enough to mount on a mast. The 10.71 per cent fractional bandwidth lets one radio cover the whole allocation, so a product family can ship one board and change only the channel plan in the software settings.
In a fixed wireless access terminal the part works differently. Those radios are usually specified at a few hundred milliwatts to one watt of average output with an OFDM signal that carries a high peak to average ratio. A two watt saturation part driven to 27 dBm average leaves six decibels of headroom, which is enough for a 64 QAM waveform and not enough for the most demanding modulation. Systems that need more headroom move to the 38 dBm member on the same band.
At 5.9 GHz the loss in the cable between the module and the antenna becomes the limit rather than the module. A one metre run of a thin coaxial cable costs about one decibel at 5.9 GHz, so a 2 W part delivering 33 dBm at the connector delivers 32 dBm at the antenna. That is why the output figure has to be quoted at the right reference plane on the purchase order and on the test record.
Choosing between HXNM40010 and its neighbours
Hisiwell lists several parts that overlap this window, and the choice is decided by drive level rather than by output. The HXNM40009 covers 5.1 to 5.9 GHz at 38 dBm with 18 dB of gain and 30 per cent efficiency. It delivers five decibels more output and ten decibels less gain, so it needs 20 dBm of drive and works as the final stage after a driver of this class.
The GaAs parts on the same band sit on a 10 V rail instead of 28 V. The HXC40019 covers 5.3 to 5.9 GHz at 36 dBm compression with 10 dB of gain and 40 per cent efficiency, and the HXC40022 reaches 45 dBm on the same window. A 10 V rail is easier to supply in a battery product and the GaAs parts carry less gain per stage, which matters when the chain has to stay linear at a high back off.
Above this band the same family covers 5.0 to 5.3 GHz with HXNM40007 at 40 dBm and 26 dB of gain, and 4.4 to 5.0 GHz with HXNM40008 at 43 dBm and 23 dB of gain. Both carry equal or more output and less gain than this part, so a system that needs both bands can use one driver stage and two final stages, which is usually cheaper than two complete chains.
Our guide to choosing an RF amplifier sets out the order we use: rail first, then mode, then band, then output, then gain. Reading the sequence in that order stops a part being selected on output alone and then failing on a 10 V supply or on a pulsed duty cycle.
Questions buyers ask before ordering HXNM40010
Is there a data sheet? No. Hisiwell publishes a category index row and a product page for this part, and both carry the same five electrical figures. There is no document with curves, scattering parameters, thermal data or package drawings. Any specification beyond those five figures has to be measured on a sample or confirmed by the factory in writing.
Can it run continuous wave at full output? The vendor lists it as continuous wave, which is the point of the part. The dissipation at saturation is 4.66 W, so a carrier of 5 C per watt holds the case rise to 23 C, and the thermal path is not the hard part at this power level. The flange, the mounting screws and the interface material still have to be right, but a two watt module is not where thermal budget usually fails.
What does the purchase order have to carry? The band, the 28 V rail, the continuous wave mode and the quantity, because none of those appear in a part number suffix. There is no published orderable addendum, no marking code and no packing column for this part, so reel size and moisture level cannot be quoted from a vendor document. They have to come from the factory on the quotation.
How do we start? Send the band, the required output at the antenna connector, the drive level available and the rail. We will confirm whether this part or one of its neighbours fits, quote from the current factory schedule, and ship a sample with the measured output and gain at the band edges. Our RF component sourcing page explains what we ask for before a quotation is issued.