HXN50217
Product Specifications
HXN50217
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN50217 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN50217: one hundred watts at 5 to 6 GHz in continuous wave
The HXN50217 is a gallium nitride power transistor from Hisiwell on the 5 to 6 GHz band with 100 W of peak output on a 28 V rail and a continuous wave mode on the index row. One hundred watts is exactly 50.00 dBm, which makes this the round number in the 5 GHz group: 50 W below it, 140 W above it.
The row carries a peak figure and no saturation, no average, no gain and no efficiency. For a continuous wave part that is an unusual set of omissions, because continuous wave operation is where the efficiency figure matters most: the part has to hold its output indefinitely, and the heat is not averaged away by a duty cycle.
The arithmetic that can be done without the vendor is still useful. At 50 ohm, 100 W is 70.7 V RMS and 100.0 V peak. Under a two to one mismatch the peak reaches 141.4 V, which is above a 100 V capacitor and inside a 250 V one. That single row decides the match hardware, and it is why a continuous wave 100 W stage is built with 250 V parts.
The current is the other half. At 100 per cent drain efficiency the drain would draw 3.57 A, which is the floor. At 50 per cent it draws 7.14 A and leaves 100 W of heat, and at 60 per cent it draws 5.95 A and leaves 66.7 W. A continuous wave 100 W part is a 67 to 100 W heater in the same box, and the sink is sized on the heat rather than on the output.
The band is 1 GHz from 5 to 6 GHz, 18.2 per cent fractional. The three parts on this window form a ladder at 50, 100 and 140 W, and this one is the middle rung, which is where most continuous wave test and satcom systems land.
The parameter rows behind the HXN50217
| Part class | Gallium nitride HEMT power transistor, unmatched |
| Frequency range | 5 to 6 GHz |
| Band width, calculated | 1,000 MHz |
| Fractional bandwidth at 5.5 GHz centre, calculated | 18.2 per cent |
| Peak output, index row | 100 W |
| Peak in dBm, calculated | 50.00 dBm, a round figure |
| Saturation output column | Not published |
| Average output column | Not published |
| Power gain | Not published |
| Drain efficiency | Not published |
| Drain current at 100 per cent efficiency, calculated | 3.57 A, a floor and not a real figure |
| Drain current at 60 per cent, calculated | 5.95 A, 66.7 W of heat |
| Drain current at 50 per cent, calculated | 7.14 A, 100.0 W of heat |
| Drain current at 40 per cent, calculated | 8.93 A, 150.0 W of heat |
| DC input at 50 per cent, calculated | 200 W |
| Drain rail | 28 V |
| Mode | Continuous wave |
| Load voltage at 50 ohm, calculated | 70.7 V RMS, 100.0 V peak |
| Load voltage under a two to one mismatch, calculated | 141.4 V peak |
| Load voltage at 12.5 ohm, calculated | 35.4 V RMS, 50.0 V peak |
| Output per gigahertz of band, calculated | 100 W per GHz |
| Matching | Unmatched, network on the customer board |
| Package and body | Not published on the index row |
| Thermal resistance, junction to case | Not published |
| Compression point | Not published |
Seven amps and a hundred watts of heat in continuous wave
Continuous wave is the hard case. A pulse part gets its heat averaged by the duty cycle and a continuous part does not, so the sink is sized on the full dissipation and the junction temperature is the limit that decides the lifetime.
At 50 per cent efficiency the part dissipates 100 W for as long as the amplifier is keyed. That is a flange on a liquid cooled plate or a very large forced air sink, and it is the reason a 100 W continuous part is often run at 80 W in a commercial product with a derating policy.
The DC feed has to carry 7.14 A at 50 per cent and 8.93 A at 40 per cent, plus the crest of a modulated signal if the continuous wave part is used with one. A choke rated at 10 A, a 300 mil trace and a bulk bank sized for the envelope is the minimum, and at 12.5 A the trace moves up another size.
The output network is the second cost. At 100 V peak and 141 V under mismatch the capacitors are 250 V parts, and the match inductors carry the circulating current of a two section ladder at 5.5 GHz. That is a more expensive network than the one on the 50 W member, and it is worth pricing before the part is chosen.
HXN50217 against the other parts on 5 to 6 GHz
| HXN50217 | 5 to 6 GHz | 100 W peak | Not published | Not published | Reference point |
| HXN50214 | 5 to 6 GHz | 50 W peak | Not published | Not published | 3.01 dB less peak |
| HXN50335 | 5 to 6 GHz | 70 W peak | Not published | Not published | 1.55 dB less peak |
| HXN50222 | 5 to 6 GHz | 140 W peak | Not published | Not published | 1.46 dB more peak, pulse mode |
| HX5060140P2 | 5 to 6 GHz | 140 W saturation | 11 dB | 50 per cent | 1.46 dB more output with gain and efficiency published |
| HX446050F2 | 4.4 to 6 GHz | 50 W saturation | 15 dB | 55 per cent | 3.01 dB less output on a wider band with 15 dB of gain |
The last row is the one that most buyers should look at first. Fifty watts with 15 dB of gain, 55 per cent efficiency and a published band from 4.4 GHz is a complete datasheet, while 100 W with no gain and no efficiency is an incomplete one. If 47 dBm at the antenna is enough, the complete datasheet is the cheaper project.
Against the 140 W pulse part the 1.46 dB difference is small and the mode difference is large. A continuous wave system takes this part, a pulsed radar takes the other, and the two are not interchangeable even though the output figures are within 1.5 dB.
Peak rated parts at this band are indexed on RF component sourcing, and the way to compare a complete and an incomplete row is set out on RF power transistor cross reference.
Board notes for a hundred watt continuous stage
The first item is the sink. One hundred watts of heat in continuous wave is a liquid plate or a large forced air sink, and the interface between the flange and the plate is the single most important joint in the assembly.
The second item is the capacitor rating. At 100 V peak and 141 V under mismatch, 250 V parts are the minimum, and the match inductors have to be rated for the circulating current at the band edges rather than at the centre.
The third item is the bias. With no published quiescent current the class is set on the first article, and for a continuous carrier the point is set at the efficiency peak. A temperature compensated gate network keeps it there.
The fourth item is drive. With no gain row the drive power is unknown, so a sample is measured at 5.0, 5.5 and 6.0 GHz before the driver is bought, and the measurement includes the flange temperature at the same time.
Questions buyers ask about HXN50217
Is 100 W the saturated output or a peak? The row is labelled peak and the mode is continuous wave. For a continuous part the two are usually close, and the sample measurement settles it.
What is the efficiency? Not published. The heat table on this page gives the range at 40, 50 and 60 per cent.
What is the drive power? Not published, because no gain row exists. That is the first figure measured on a sample.
Can it be pulsed? The mode row reads continuous wave. Pulsing a continuous part is usually acceptable at a lower average, and the limit is set by the junction temperature rather than by the mode word.
How do we start? Send the band, the output at the connector, the signal, the ambient and the rail. We will confirm the missing rows with the factory, quote from the schedule and ship a sample measured at 5.0, 5.5 and 6.0 GHz under continuous drive.