HXN50160F
Product Specifications
HXN50160F
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN50160F from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN50160F: 800 W pulsed across 1200 to 1600 MHz with a 20 W drive and a 533 W heat load
The HXN50160F is a gallium nitride HEMT on the 50 V shelf with a 1.2 to 1.6 GHz window, an 800 W row, 16 dB of gain and 60 per cent efficiency, all in pulse mode. It is the widest windowed member of the L band pulse group and the one with the most complete set of published columns: gain and efficiency are both there, which is not true of the DC to 4 GHz rows on the same table.
The page is short. It calls the part an 800 watt internally matched GaN HEMT for pulsed amplifier applications from 1.2 to 1.6 GHz and states that there is no performance guarantee outside that band. There is no parameter block, no package drawing and no data sheet link, so the four numbers on the row are the whole published specification.
For a buyer the useful consequence is that this part can be quoted from the catalogue. The drive, the current and the heat all follow from figures the vendor publishes, which makes it the exception on a shelf where most rows carry power and nothing else. The gaps are in the mechanical side and in the pulse condition, not in the electrical columns.
The HXN50160F rows as the vendor publishes them
| Part class | Gallium nitride HEMT, internally matched input, pulsed |
| Frequency range, index row | 1.2 to 1.6 GHz |
| Window width, calculated | 400 MHz |
| Band ratio, calculated | 1.33 to 1 |
| Saturation output, index row | 800 W, 59.03 dBm |
| Output per megahertz of window, calculated | 2.0 W |
| Gain, index row | 16 dB |
| Drive level at 16 dB, calculated | 20.1 W, 43.03 dBm |
| Drain efficiency, index row | 60 per cent |
| DC input at 60 per cent, calculated at continuous duty | 1333 W |
| Drain current at 50 V, calculated at continuous duty | 26.67 A |
| Heat at continuous duty, calculated | 533 W |
| Drain rail, index row | 50 V |
| Load voltage at 800 W into 50 ohm, calculated | 200.0 V rms, 282.8 V peak |
| Peak against the rail, calculated | 5.66 times |
| Peak at a 2 to 1 mismatch, calculated | 565.7 V |
| Mode, index row | Pulse |
| Mode, product page | Pulsed amplifier applications |
| Pulse width and duty cycle | Not published |
| Matching, product page | Internally matched |
| Matching, index shelf | Listed on the unmatched GaN table |
| Package, flange and body | Not published, the F suffix is not explained |
| Thermal resistance | Not published |
| Load impedance and load pull | Not published |
| Data sheet | No document linked from the page |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
| Applications listed | Wireless infrastructure, wideband amplifier, EMC testing, ISM |
Where the 800 W lands in the signal chain
800 W is 59.03 dBm, and 16 dB of gain means 20.1 W of drive, which is 43.03 dBm. That is a comfortable one stage driver for most pulsed systems and the reason this part is easier to specify than the low gain members of the shelf: a part with 13 dB of gain would need 40 W of drive for the same output, and 40 W of drive changes the driver from a small module into a second amplifier.
The output side carries 200.0 V rms and 282.8 V peak, which is 5.66 times the 50 V rail and 565.7 V peak at a 2 to 1 mismatch. The same voltage class applies to the output match, the connector and the circulator, so the passive parts around this device are not small signal parts even though the device itself is a single flange.
The heat is the number a chassis is built around. At 60 per cent efficiency the DC input is 1333 W, the drain current is 26.67 A and the heat is 533 W at continuous duty. At a 10 per cent duty the average heat falls to 53 W, which is a forced air heatsink, while the pulse current stays at 26.67 A, which the supply and the decoupling still have to deliver. Both cases come from the same published row, and the difference between them is the duty cycle that the vendor has not published.
The F suffix and the package question
Nothing on the page says what the F stands for, and the shelf is not consistent about it either: the HX30370P ends in P and its page describes a flanged package, while the HX38300P ends in P and its page describes an unflanged one. On this table a trailing letter is not a reliable guide to the flange, and a purchase order that assumes it is will receive a device that does not fit the cavity.
The practical handling is to specify the mounting in words: flanged or flangeless, screw or clamp, and the screw pattern if the buyer already has a cavity. Where the amplifier is a new build, the flange question can wait for the first sample. Where the board already exists, it cannot, because the flange sets the ground path, the thermal interface and the height above the board.
The same applies to the body material and the lid. Neither is published, and both decide the reflow profile and the cleaning route if the part is assembled rather than screwed down.
Where the HXN50160F sits on the 50 V shelf
The neighbours are the two other L band pulse rows. The HXN50162x2 is 1500 W over 1200 to 1400 MHz with the same 16 dB of gain and 58 per cent efficiency, which is 2.73 dB more output on half the window and needs 37.68 W of drive instead of 20.1 W. The HX5141K00VP is a single 1000 W device over 960 to 1400 MHz with 18 dB and 70 per cent, 0.97 dB above this row, with a wider window and two more dB of gain.
Against those two, the HXN50160F is the middle answer: the widest window of the three at the low end of the group, the lowest drive requirement, and a published efficiency that lets the heatsink be sized before the first prototype. Where the band is fixed at 1200 to 1400 MHz and the drive is available, the 1500 W pair is the better buy by 2.73 dB. Where the band has to cover 1.2 to 1.6 GHz, this is the only row on the shelf that does it at this power. The drive figure for each row is collected on the RF power transistor cross reference page.
What an order for the HXN50160F has to state, and what it cannot yet
No orderable addendum, packing quantity, marking code or moisture level is published, and no data sheet is linked. The purchase order has to carry the part number, the window, the rail, the pulse width and duty, the mounting (flanged or flangeless), the quantity and the incoming test. It should also ask for the thermal resistance and the pulse condition, because the 533 W heat figure is a continuous duty number and the real heat load depends on both.
The incoming gate for a pulsed part should include a pulse test at the agreed condition and not only a DC bias check, because a device that is fine at DC can still be short at the pulse width the system uses. The incoming inspection plan page sets out how to size that test to a lot, and where the same chassis needs its driver and its circulator against one date, the consolidated route is on the one stop RF supply page.
Questions buyers ask about the HXN50160F
How much drive does it need? 20.1 W at 16 dB of gain, which is 43.03 dBm. That is a single small driver stage in most systems.
Is the F a flanged package? Not stated anywhere on the page, and the shelf is inconsistent about trailing letters. Specify the mounting in words on the order rather than relying on the suffix.
Can it run continuous? The mode is pulse and every figure on the row is a pulse figure with no width and no duty. A continuous claim would need a factory answer and a bench check.
What is the heat load? 533 W at continuous duty from the published 60 per cent efficiency, falling with duty. Both the supply and the heatsink should be sized from the figure that matches the waveform, not from a catalogue habit.