HXN40049
Product Specifications
HXN40049
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40049 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40049: twenty watts at 4.4 to 5 GHz, still on 28 V
The HXN40049 is the third rung of the Hisiwell 4.4 to 5 GHz ladder and the last one that keeps the 12 dB gain floor. The published row reads 4.4 to 5 GHz, saturated output at least 43 dBm, gain at least 12 dB, drain efficiency at least 45 per cent, 28 V drain rail, plus or minus 0.8 dB of flatness, continuous wave. Input and output impedance are 50 ohm, and the match is synthesised on a film hybrid carrier.
Twenty watts of radio frequency at 45 per cent efficiency draws 44.3 W from the 28 V rail, which is 1.58 A, and leaves 24.4 W of heat on the flange. Drive at 12 dB gain is 31 dBm, 1.26 W. At this level the drain current is no longer a detail: the feed, the choke and the decoupling bank are carrying an ampere and a half continuously, and the ground return under the source has to be planned rather than inherited from a smaller board.
The output voltage into 50 ohm at saturation is 31.6 V RMS and 44.7 V peak, which is above the 28 V rail. That is normal for a matched GaN stage and it is the reason an output isolator or a circulator is worth having: an open or a short at the antenna reflects a voltage the drain was not specified against.
The part suits a driver for a 47 dBm or 50 dBm final stage, a medium power fixed link, or a radar exciter. It is also the largest member of the band that a board built for the five watt part can carry without changing the supply, which makes it the usual upgrade path inside one product.
The parameter rows Hisiwell publishes for HXN40049
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 4.4 to 5 GHz |
| Bandwidth, calculated | 600 MHz, 12.8 per cent fractional at a 4.70 GHz centre |
| Saturation output power as published | at least 43 dBm |
| Saturation output power in watts, calculated | 19.95 W |
| Gain as published | at least 12 dB |
| Drain efficiency as published | at least 45 per cent |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Match technology as described by the vendor | in plane matching synthesis, film hybrid integration |
| Output at 1 dB compression | not published, the index prints a slash |
| DC input at saturation, calculated | 44.3 W |
| Drain current at saturation, calculated | 1.58 A at 28 V |
| Dissipation at saturation, calculated | 24.4 W |
| Dissipation if efficiency falls to 40 per cent, calculated | 49.9 W |
| Drive power for the rated output, calculated | 31 dBm, 1.26 W |
| Output per 100 MHz of the band, calculated | 3.33 W |
| Load voltage at saturation into 50 ohm, calculated | 31.6 V RMS, 44.7 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, one image on the product page |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Neighbour on the same band at 40 dBm | HXN40048, same rail, same gain floor |
| Neighbour on the same band at 47 dBm | HXN40050, same rail, 11 dB gain |
The heat path is the binding constraint at twenty watts
24.4 W of dissipation on a 3 C per watt carrier is 73 C of rise over the case, and on a 5 C per watt carrier it is 122 C. The second number is already above any sane case limit, so the carrier and the sink together have to be around 2 C per watt or better for this part to be usable at saturation in a warm enclosure.
The efficiency row is a floor, so a build that lands at 40 per cent instead of 45 per cent sees 49.9 W of dissipation rather than 24.4 W. Doubling the heat for a five point efficiency miss is the single most common surprise on a part like this, and it is why the proposal should be quoted against the floor rather than the typical.
Backing off 6 dB brings the output to 5.01 W and the dissipation, at an assumed 30 per cent in backoff, to 11.7 W. That is the same heat as the ten watt member at saturation, which is a useful coincidence when one chassis has to carry both builds.
The same soak test answers the question that the document leaves open. A thermocouple on the flange, thirty minutes at saturation, and a record of the sink inlet temperature tell a build more about its margin than any derating curve the vendor did not publish, and the numbers transfer directly to the next chassis of the same shape.
Where the ladder changes character
Up to this part the 4.4 to 5 GHz ladder keeps 28 V, continuous wave and a 12 dB gain floor, and the output runs 5.01, 10.00 and 19.95 W. The next members keep 28 V but drop the gain floor: 47 dBm at 11 dB and 50 dBm at 10 dB. That single number changes the driver budget more than the power does, because 3 dB less gain at the same output means double the drive.
Above 50 dBm the rail or the mode changes. The 51 dBm member runs on 32 V and the 53 dBm member is pulsed at 100 microseconds and 10 per cent duty. A four stage amplifier chain built from this band therefore uses 28 V stages up to 100 W and then either raises the rail or shortens the pulse.
For a cross reference the ladder matters because a customer replacing a competitor part usually quotes the rail and the mode first. Our RF power transistor cross reference page lists the four fields we ask for before any candidate is proposed.
What has to be settled at first article
The gate bias is not published, so quiescent current has to be set on the bench. There is no pinch off voltage, no recommended quiescent point and no gate voltage window in the vendor document, and at 1.58 A of drain current a wrong bias point destroys the part quickly rather than degrading it slowly.
The drain feed has to be sequenced. With no absolute maximum table there is no published overshoot allowance, so a clamp on the choke and a sequenced gate before drain is the conservative route. The same applies to the drive: 1.26 W of drive at the floor is enough that a driver fault can overdrive the input.
An isolator at the output is worth the board space at this power. The 44.7 V peak at saturation into 50 ohm is a matched load figure, and a mismatched antenna raises it. Our guide to choosing an RF amplifier covers the protection order we recommend for a stage at this level.
Questions buyers ask about HXN40049
Is it a drop in for the ten watt member. Mechanically the carrier family is the same and the electrical rows are the same except for the power, so the board can carry either, but the heatsink and the feed have to be sized for the twenty watt part.
Does it need a different rail. No. 28 V is the published rail for this member and for the five and ten watt members, and the rail only changes at the 51 dBm part above it.
What is the peak power. The vendor publishes saturated output only and prints a slash in the 1 dB compression column, so there is no separate peak figure. For a pulsed system the number to work from is the continuous wave saturation with a duty cycle applied to the dissipation.
How is it ordered. Through the RF procurement route with the band, rail, mode and quantity on the request; packing and reel format are confirmed with the factory because the vendor page carries no orderable addendum.