HXN40034
Product Specifications
HXN40034
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40034 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40034: 199.5 W over 2.8 to 3.6 GHz from a 50 V rail
The HXN40034 is the first 50 V member of the Hisiwell S band group and the first with a band narrower than a full gigahertz. It covers 2.8 to 3.6 GHz, 800 MHz wide, and delivers at least 53 dBm at saturation, which is 199.5 W, with 12 dB of gain and 50 per cent typical drain efficiency, in 100 microsecond pulses at a 20 per cent duty cycle, with plus or minus 0.8 dB of flatness.
At 50 per cent the rail supplies 399.1 W during the pulse, the drain current is 7.98 A at 50 V, and the heat is 199.5 W. On a 20 per cent duty the average dissipation is 39.9 W and the average current 1.60 A, which is a comfortable steady load for a carrier that has to carry 199.5 W for a fifth of every millisecond.
The 50 V rail halves the current for the same power compared with the 32 V member, and that is the practical reason the ladder moves up in voltage as the output rises: 7.98 A through a flange, a bond wire array and a feed is a packaging problem that can be solved, while 12.5 A through the same structures is harder and hotter.
The band is 800 MHz rather than 1000 MHz, and that narrowing is what pays for the higher power on the same carrier class. A 2.8 to 3.6 GHz window still covers the S band radar allocations and the fixed link blocks inside them, and it stops short of 3.7 GHz where the wider members of the family reach.
The parameter rows Hisiwell publishes for HXN40034
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 2.8 to 3.6 GHz |
| Bandwidth, calculated | 800 MHz, 25 per cent fractional |
| Saturation output power as published | at least 53 dBm |
| Saturation output power in watts, calculated | 199.5 W |
| Gain as published | at least 12 dB |
| Drain efficiency as published | at least 50 per cent, typical |
| Drain voltage | 50 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | pulsed, 100 microsecond width at 20 per cent duty |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Output at 1 dB compression | not published, the index prints a slash |
| DC input at saturation, calculated | 399.1 W |
| Drain current at saturation, calculated | 7.98 A at 50 V |
| Dissipation during the pulse, calculated | 199.5 W |
| Average dissipation at 20 per cent duty, calculated | 39.9 W |
| Average drain current at 20 per cent duty, calculated | 1.60 A |
| Charge drawn per 100 microsecond pulse, calculated | 0.80 mC |
| Drive power for the rated output, calculated | 41 dBm, 12.6 W |
| Dissipation if efficiency falls to 45 per cent, calculated | 243.9 W |
| Thermal resistance, junction to case | not published |
| Transient thermal impedance | not published |
| Package outline and dimensions | not published in text, one image on the product page |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published on this page |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Neighbour below, wider band | HXN40033 at 52 dBm over 2.7 to 3.7 GHz on a 32 V rail |
| Neighbour above, narrower band | HXN40039 at 54 dBm over 3.1 to 3.4 GHz on the same rail |
Twenty per cent duty and two hundred watts of pulse heat
The duty cycle here is the highest in the S band group, 20 per cent against the 10 per cent carried by the members either side, so the average heat is doubled for the same peak: 39.9 W instead of 20 W. That is still inside a forced air budget on a good carrier, but it is the number to compare when a system is deciding between this part and the 54 dBm member with the narrower band.
At 100 microseconds and 20 per cent duty the repetition rate is 5 kHz, and the charge drawn per pulse is 0.80 mC. A rail allowed to sag 2 V needs 0.4 mF close to the device, and the loop between the bank, the feed and the flange decides the droop at 7.98 A of leading edge current.
The thermal question inside the pulse is unchanged by the duty cycle: 199.5 W crosses the die for 100 microseconds and there is no transient thermal impedance curve to compute the excursion. What the duty changes is the average case temperature, and that affects the starting point of every pulse. A case held 20 C cooler by a better heatsink gains more margin at the junction than a shorter pulse would on the same heatsink.
Efficiency at 45 per cent raises the pulse heat to 243.9 W and the current to 8.87 A, which is 22 per cent more heat in the same flange. The typical marking means it is a number to specify rather than to assume.
Where the 2.8 to 3.6 GHz window is the useful part
A 800 MHz window centred near 3.2 GHz covers the S band radar allocations and the fixed and mobile blocks inside them, and it leaves out the 3.7 GHz edge that only the wider members reach. A system that owns a 3.1 to 3.4 GHz allocation does not need the extra band, and the narrower match is what allows 199.5 W on a carrier that would otherwise be limited to a smaller die.
For a buyer the question is whether the system will ever need to move outside the window. If the answer is no, the narrower band is free performance. If the answer is yes, the 52 dBm member on 2.7 to 3.7 GHz is the one to compare, at 158.5 W and a 32 V rail, and the trade is 40 W of output against 200 MHz of band.
The 50 V rail is the other decision. It halves the current and eases the feed, and it raises the isolation and sequencing requirements on the drain. Systems already built around 50 V, which is common in radar and in base station hardware, take this part without a supply change.
Where a 199.5 W pulse stage fits
The fit is a radar or instrumentation transmitter over 2.8 to 3.6 GHz, a satellite ground station driver, a datalink power stage or a laboratory amplifier for high power component testing. Two hundred watts in 100 microsecond pulses at 20 per cent duty is a practical radar class, and the 12 dB gain means a 12.6 W driver, which is available in this family and in the wider market.
It is a poor fit for continuous wave, for a long pulse at 20 per cent duty, and for a system that needs a compression point in writing. Our RF power transistor cross reference work prints the band, the rail, the duty cycle and the drive of the S band members in one table, because those four decide whether a heatsink and a driver carry over from one part to the next.
Where the application is a defence programme, the screening and temperature class options are set out in our defence grade component supply view, and a part with no published operating range has to have that range agreed in writing before qualification starts.
Questions we answer on HXN40034 before a lot is booked
The first is the pulse length at the system level. The 100 microsecond row is the vendor condition; a longer key at the same duty is a different thermal question.
The second is the flange and the feed. At 7.98 A of pulse current the mounting, the pin arrangement and the flatness of the interface are part of the device, so the outline drawing is worth asking for before the assembly is fixed.
The third is the lot. With no addendum, no marking and no moisture level published, the purchase order names the band, the rail and the pulse condition, and the incoming inspection plan records what arrives. A saturated power sweep at 3.2 GHz and a case temperature at the rated pulse belong on the customer bench or at a partner RF laboratory, and the RF procurement process states that division before the first order.