Contact Us

HXN40030

Brand: Hisiwell
Hisiwell HXN40030 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN40030 — Discrete & Power Semiconductors | Superb Automation

HXN40030

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN40030 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN40030: ten watts of continuous wave across a full gigahertz

The HXN40030 is the smallest member of the Hisiwell group that covers 2.7 to 3.7 GHz, and the band is the reason to look at it. One gigahertz of span at the bottom of S band is a fractional bandwidth of just over 30 per cent, and a part that holds 40 dBm at saturation with plus or minus 0.8 dB of flatness across that span does so with the match built into the carrier rather than with a network added on the board. The vendor describes the family as internally matched, 50 ohm at both ports, built with in-plane matching synthesis on a film hybrid carrier, and it lists a single impedance for input and output rather than a matching recipe.

The published rows are: 2.7 to 3.7 GHz, saturated output at least 40 dBm, gain at least 12 dB, drain efficiency at least 45 per cent, 28 V drain rail, plus or minus 0.8 dB of flatness, continuous wave operation. Ten watts of radio frequency at 45 per cent efficiency is 22.2 W drawn from the rail, which at 28 V is 0.79 A, and 12.2 W of heat that has to leave the flange. Drive at the 12 dB gain floor is 28 dBm, which is 0.63 W.

A 28 V rail is the low end of this family and it is worth noticing, because the same band carries a 32 V member and a 50 V member further up the ladder. On a 28 V bus the drain current for ten watts is under an ampere, so the feed, the capacitor bank and the decoupling are ordinary, and the engineering problem moves entirely to the heat path and to the flatness across the gigahertz.

The vendor sells this part as continuous wave, not pulsed, so the 12.2 W of dissipation is a steady load and not an average of a burst. On a carrier offering 3 C per watt that is 37 C of rise over the case, which is usable with a modest heatsink and is the number to check before the part is put on a small amplifier board with no metal under it.

The parameter rows Hisiwell publishes for HXN40030

Part classGallium nitride power transistor, internally matched
Frequency range2.7 to 3.7 GHz
Bandwidth, calculated1000 MHz, 31 per cent fractional
Saturation output power as publishedat least 40 dBm
Saturation output power in watts, calculated10.0 W
Gain as publishedat least 12 dB
Drain efficiency as publishedat least 45 per cent
Drain voltage28 V
Flatness across the bandplus or minus 0.8 dB
Operating modecontinuous wave
Input impedance50 ohm
Output impedance50 ohm
Output at 1 dB compressionnot published, the index prints a slash
DC input at saturation, calculated22.2 W
Drain current at saturation, calculated0.79 A at 28 V
Dissipation at saturation, calculated12.2 W
Dissipation if efficiency falls to 40 per cent, calculated15.0 W
Drive power for the rated output, calculated28 dBm, 0.63 W
Output per 100 MHz of the band, calculated1.0 W
Thermal resistance, junction to casenot published
Package outline and dimensionsnot published in text, one image on the product page
Scattering parametersnot published
Pinch off voltage and gate bias pointnot published on this page
Operating and storage temperaturenot published
Moisture level and floor lifenot published
Orderable addendum and packingnot published
Neighbour on the same band at 45 dBmHXN40031, same rail, same gain floor
Neighbour on the same band at 49 dBmHXN40032, same rail, 10 dB gain

Why one gigahertz at ten watts is the difficult row

An internally matched part is a compromise between the bandwidth the match can hold and the power the die can deliver. The vendor's own ladder shows the shape of that compromise: on the 2.7 to 3.7 GHz band the output runs from 10 W through 31.6 W and 79.4 W to 158.5 W, and the wider the power the lower the efficiency figure printed against it. Here the efficiency is 45 per cent and the output is the smallest of the four, which is what a build that prioritises flatness over near band efficiency looks like.

For a system builder the flatness row is the one that pays. A plus or minus 0.8 dB window across 2.7 to 3.7 GHz means one amplifier can cover a radar band, a 3.5 GHz fixed link block and the test tone positions a laboratory needs, without a switched filter bank or a retune. The cost is the 12.2 W of steady heat and the 0.63 W of drive, both modest, and a gain floor of 12 dB, which is low enough that any real chain has to account for the cable and connector loss between the driver and this stage.

The efficiency row has no minimum and no typical marked on the index, so the 45 per cent is read as the published number rather than a guaranteed one. At 40 per cent the DC input rises to 25 W, the drain current to 0.89 A and the heat to 15 W, which is a 23 per cent increase in the load on the heatsink for the same 10 W of radio frequency. On a ten watt part that is a small absolute change and an easy one to absorb; on the 158.5 W member of the same band it turns into 79 W.

The rows the product page does not carry

There is no data sheet for this part on the vendor site. The index table carries nine columns and the product page repeats frequency, saturated power, gain, efficiency and the 50 ohm ports, and neither source adds a curve. That means no gain against frequency, no return loss, no compression point, no thermal resistance and no bias window, and each of those is a question the first article has to answer by measurement.

The compression row matters most for a continuous wave part. The index has a column for output at 1 dB compression and every row in this family prints a slash in it, so 40 dBm is saturated output and nothing is said about linear operation. A system with a modulated carrier has to plan against a saturation point above the average power it needs, and the margin has to be established on the bench rather than read off the page.

The bias window is the second gap. No pinch off voltage and no quiescent current is printed for this part. The one full document in the family, which is the HX2734P600W sheet linked from the HXN42001 page, prints a pinch off window of minus 1.5 to minus 3.5 V and a 5 V gate ceiling, and that is a starting point for a first article on a 28 V part, not a substitute for the sheet of this one. The gate supply has to be established before the drain on every power up, and the sequencer has to survive a brownout without inverting that order.

The mechanical rows are the third gap. One outline image, no dimension table, no flange drawing and no recommended mounting torque. On a ten watt part the thermal interface is forgiving, but the pin positions decide whether the part drops onto an existing amplifier footprint, and that is worth asking before a board is cut.

Where a ten watt octave stage fits

The obvious position is a driver. The 158.5 W member of the same band, the HXN40033, needs 10 W of drive at its own 12 dB gain floor, which is exactly the output of this part, so a two stage chain from 0.63 W to 158.5 W can be built from two parts of the same family on the same rail family. That is a chain with one vendor, two flanges and a single flatness specification across the gigahertz.

The second position is a test or instrumentation amplifier where the band has to move: an antenna range, a receiver sensitivity bench, a component test set that sweeps 2.7 to 3.7 GHz. Ten watts is enough to drive a directional coupler and a power meter without a separate amplifier, and the 50 ohm ports remove the matching work.

The third is a low power radar or a fixed link transmitter where the antenna gain does the rest of the work. It is a poor fit for any application that needs a compression point on paper, for a system that cannot hold the gate bias before the drain, and for a build where no metal sits under the part. Our RF power transistor cross reference work keeps the four outputs on this band in one table with the rail, the efficiency and the drive of each, and the one stop RF supply view is where the flange and the feed parts for a chain like this are grouped.

Questions we answer on HXN40030 before a lot is booked

The first is the band edge. A match that holds plus or minus 0.8 dB from 2.7 to 3.7 GHz is centred somewhere inside that window, and a system that operates at 3.8 GHz is outside it. Ask where the match was centred and what the gain does 100 MHz beyond each edge.

The second is the arriving lot. With no orderable addendum, no marking code and no moisture level published, the purchase order has to name the band and the rail, and the incoming inspection plan then records the flange, the marking and the DC behaviour at gate and drain that can be measured without an RF bench. A power sweep at 3 GHz belongs on the customer bench or at a partner RF laboratory, and the quotation says which.

The third is the bias sequence and the heat path. Our RF procurement process puts the gate supply order, the case temperature target and the mounting method in front of the vendor before the first lot, because those three decide whether a ten watt part survives its first hundred hours.