Contact Us

HXN40023

Brand: Hisiwell
Hisiwell HXN40023 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN40023 — Discrete & Power Semiconductors | Superb Automation

HXN40023

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN40023 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN40023: 398 W over 200 MHz of the 1.9 to 2.1 GHz band

The HXN40023 is the 56 dBm member of this family that covers 1.9 to 2.1 GHz. The published rows are 1.9 to 2.1 GHz, saturated output at least 56 dBm, drain efficiency at least 50 per cent typical, 50 ohm ports, a 50 V drain rail, plus or minus 0.8 dB of flatness and pulsed operation at a 1 ms pulse width and 10 per cent duty. The gain row is the one that needs care, and the next section explains why.

The band is twice as wide as the 1.6 to 1.7 GHz window and it straddles two different uses: the 1.9 to 2.0 GHz cellular uplink, and the 2.0 to 2.1 GHz downlink block that sits above it, with satellite and fixed link services in the same stretch of spectrum. A part with one internal match spanning 200 MHz at 398 W is a wideband saturated stage rather than a channelised one, which is useful for a test amplifier or a multi carrier transmit chain and less useful where a single 20 MHz channel needs the last tenth of a dB.

At 56 dBm and 50 per cent efficiency the DC input is 796 W, the drain current 15.9 A at 50 V, the dissipation during the pulse 398 W and the drive 44 dBm, which is 25.1 W. Both numbers put this part in the same supply class as the 1.6 GHz member, and the difference between the two parts is the band, the gain row and the pulse duty: 10 per cent here against 20 per cent there, which halves the average dissipation.

The construction is the usual one for this family, an internally matched die on a film hybrid carrier in a metal package, with the match built for the band at the time of supply. Nothing on the page suggests any tuning is available to a user, and no external matching is expected at either port.

The parameter rows Hisiwell publishes for HXN40023

Part classGallium nitride power transistor, internally matched
Frequency range1.9 to 2.1 GHz
Saturation output power as publishedat least 56 dBm
Saturation output power in watts, calculated398.1 W
Gain, index table row12 dB
Gain, product page rowat least 13 dB
Drain efficiency as publishedat least 50 per cent, typical
Drain voltage50 V
Flatness across the bandplus or minus 0.8 dB
Operating modepulsed, 1 ms pulse width at 10 per cent duty
Input impedance50 ohm
Output impedance50 ohm
Output at 1 dB compressionnot published, the index prints a slash
DC input at saturation, calculated796.2 W
Drain current at saturation, calculated15.92 A at 50 V
Dissipation during the pulse, calculated398.1 W
Average dissipation at 10 per cent duty, calculated39.8 W
Average drain current at 10 per cent duty, calculated1.59 A
Drive power from the 12 dB row, calculated44 dBm, 25.1 W
Drive power from the 13 dB row, calculated43 dBm, 20.0 W
Thermal resistance, junction to casenot published
Package outline and dimensionsnot published in text
Scattering parametersnot published
Pinch off voltage and gate bias pointnot published on this page
Operating and storage temperaturenot published
Moisture level and floor lifenot published
Orderable addendum and packingnot published
Neighbour at 56 dBm in the 2.2 to 2.4 GHz bandHXN40029, same rail, 12 dB gain

Two gain rows on the same part

The index table prints 12 dB for this part and the product page prints at least 13 dB, and those two rows lead to different chains. At 12 dB the drive needed for 56 dBm is 44 dBm, which is 25.1 W; at 13 dB it is 43 dBm, which is 20.0 W. A driver chain planned on the higher figure and delivered on the lower one is 5 W short at the input, and at this power level 5 W is a whole driver stage.

The conservative reading is to buy the 12 dB row and treat 13 dB as upside. The reason is that both rows are floors rather than typicals, and neither is accompanied by a gain against frequency curve, so the real question is what the gain does at 1.9 GHz and at 2.1 GHz relative to the centre of the band. On an internally matched part with plus or minus 0.8 dB of flatness in saturated power, a 1 dB gain roll off at the band edge is entirely normal, and it would put the edge of the band at the 12 dB floor while the centre sat at 13 dB.

For a buyer, the practical consequence is a driver with 3 dB of headroom above the 25.1 W computed from the lower row. That headroom also covers the loss of the isolator, the cable and the connector between the driver and this part, which at 2 GHz is easily 1 dB across a production assembly.

What 10 per cent duty changes

At a 10 per cent duty cycle the average dissipation is 39.8 W and the average drain current is 1.59 A, which is a modest load for a carrier and a supply. The peak figures are unchanged: 796 W of DC input for 1 ms, 15.9 A of drain current, 398 W of heat while the pulse is on. The supply still has to deliver the peak, and the capacitor bank still has to hold the rail across the pulse, so a 10 per cent duty cycle relaxes the cooling and not the power chain.

The pulse energy is 0.8 J, and the charge drawn per pulse is 15.9 mC, the same as the 20 per cent member. A bank that can sag 2 V needs 7.9 mF, and the ESR path through the capacitors, the feed and the device flange is what sets the leading edge droop. That droop, not the average current, is what most often turns a 56 dBm plan into a 55 dBm product on the bench.

Efficiency has the same sensitivity as elsewhere in the family. At 45 per cent the dissipation during the pulse is 486.6 W and the drain current 17.7 A; at 55 per cent they fall to 325.7 W and 14.5 A. With no minimum efficiency published, the purchase specification has to state the number the system needs, and the first article has to demonstrate it at the customer's centre frequency rather than at the middle of the published band.

Where a 398 W stage at 1.9 to 2.1 GHz fits

The natural position is a transmit chain where the band is fixed and wide, and where the modulation is either constant envelope or backed off far enough that the saturated rating is the ceiling rather than the operating point. Test amplifiers for base station hardware, laboratory drivers for high power load pull, satellite uplink blocks and pulsed instrumentation radar all sit inside the envelope of a 200 MHz part at 398 W on a 10 per cent duty cycle.

It is a poor fit for a multicarrier cellular transmitter at full average power, because the compression point is not published and the saturated figure says nothing about linearity; a system that needs 56 dBm of average power needs a device rated several dB above it. It is also a poor fit for continuous wave, and a poor fit where the driver cannot supply 25 W.

Our RF power transistor cross reference work lists this part against the 1.6 to 1.7 GHz member and the 2.2 to 2.4 GHz member with the gain row and the duty cycle spelled out, because those are the three rows that decide whether a given driver and heatsink will carry over from one band to the next.

Questions we answer about HXN40023 before a lot is booked

The first is which gain row the vendor will guarantee on the order. Ask for the gain at both band edges in writing, and if the answer is only the index figure, plan the driver on 12 dB.

The second is the drain rail. Fifteen and a half amperes of pulse current at 50 V needs a feed with low inductance and a bank that holds the rail for 1 ms. Our RF procurement process puts the rail, the droop allowance and the pulse shape in front of the vendor before the first lot, because the band and the pulse condition are what the vendor tunes the match for.

The third is the documentation set. No moisture level, no marking code and no orderable addendum is published for this part, so the purchase order has to carry the band, the rail and the duty cycle, and the incoming inspection plan records the flange, the marking and the DC behaviour of each lot. A saturated power sweep at 2 GHz belongs on the customer bench or at a partner RF laboratory, and the quotation states that division rather than implying a bench that does not exist.