HXN40014
Product Specifications
HXN40014
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40014 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40014: 49 dBm across 1.35 to 1.8 GHz from 28 V
The HXN40014 moves the band rather than the power. Where the rest of this ladder sits at 1.2 to 1.4 GHz, this part covers 1.35 to 1.8 GHz, a span of 450 MHz, and delivers at least 49 dBm of saturation power with at least 12 dB of gain and 50 per cent efficiency marked typical, from a 28 V drain, with plus or minus 0.8 dB of flatness in continuous wave.
Forty nine dBm is 79.4 W. At 50 per cent efficiency the DC input is 158.9 W, the drain current is 5.67 A at 28 V and the heat is 79.4 W. The drive for rated output at 12 dB of gain is 37 dBm, or 5 W, which is a comfortable level for a driver stage and lower than the 10 W needed to drive the 200 W pulsed member. This part is therefore the easiest of the family to drive to its rated output, at the cost of 3 dB of gain against the 1.2 to 1.4 GHz members.
The band is the reason to buy it. From 1.35 to 1.8 GHz sits the GNSS L1 signal at 1575.42 MHz, the Iridium uplink and downlink allocations around 1616 to 1626.5 MHz, the Inmarsat L band uplink from 1626.5 to 1660.5 MHz, and the passive earth exploration allocation from 1400 to 1427 MHz. A single internally matched device covering 450 MHz is what a multi band terminal, a test set or a satellite modem front end wants, because one part then serves several bands and the bill of materials stops multiplying.
Four hundred and fifty megahertz is a wide band for an internally matched device, and the flatness row is the one to read carefully. Plus or minus 0.8 dB across that span is a saturated figure, and it says that the internal match holds the output within a 1.6 dB window over a 31 per cent bandwidth, which is a genuinely wideband result for a packaged GaN part with a film hybrid match on board.
The parameter rows the vendor publishes
| Part class | Gallium nitride power transistor with internal matching |
| Frequency range | 1.35 to 1.8 GHz |
| Bandwidth, calculated | 450 MHz, 31 per cent of centre frequency |
| Saturation power as published | at least 49 dBm |
| Saturation power in watts, calculated | 79.4 W |
| Gain as published | at least 12 dB |
| Efficiency as published | 50 per cent typical |
| Output at 1 dB compression | not published |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| DC input at saturation, calculated | 158.9 W |
| Dissipation at saturation, calculated | 79.4 W |
| Drain current at saturation, calculated | 5.67 A |
| Drive power for rated output, calculated | 37 dBm, 5 W |
| Coverage of GNSS L1 at 1575.42 MHz | inside the band |
| Coverage of Iridium at 1616 to 1626.5 MHz | inside the band |
| Coverage of Inmarsat uplink at 1626.5 to 1660.5 MHz | inside the band |
| Matching technology | in-plane matching synthesis on a film hybrid carrier |
| Stated application | RF and microwave systems |
| Package and flange | not published on the parameter page |
| Thermal resistance | not published |
| Scattering parameters | not published |
| Gain against frequency | not published, only the flatness row |
| Operating and storage temperature | not published |
| Orderable addendum | not published |
| Narrower band, higher power, same rail | HXN40010 at 53 dBm over 1.2 to 1.4 GHz pulsed |
| Higher band member | HXN40017 at 56 dBm over 1.6 to 1.7 GHz from 50 V |
| Higher band member, wider | HXN43002 at 50 dBm over 2 to 4 GHz from 28 V |
What 79 W continuous wave needs underneath it
Continuous wave at 49 dBm is 79.4 W of heat for as long as the carrier is on, and this is the highest continuous wave dissipation in the band. The vendor publishes no junction to case figure, so the carrier has to be chosen from experience: a copper tungsten base with a sintered interface and a heatsink of 0.6 to 1 C per watt is the normal region. At 1 C per watt, 79.4 W is 79 C of rise, which a 60 C cabinet turns into 139 C at the junction, inside a GaN limit and outside a comfortable margin.
That puts this part in the liquid cooled or forced air class. A 1.5 C per watt stack gives 119 C of rise and no cabinet above 30 C will work. The arithmetic is unforgiving and it is the same arithmetic for every continuous wave member of the family, which is why the pulsed members exist: the same output in a 10 per cent pulse is 7.9 W of average heat.
The 28 V rail helps here. At 5.67 A the DC feed is half the current of the 126 W part on 32 V, so the copper, the choke and the decoupling are all smaller for the same order of output. The trade is 3 dB less gain and 47 W less output, which is usually the right trade in a product where the supply is already 28 V.
Where the datasheet stops and the bench starts
A wide band part needs a gain against frequency curve more than a narrow band part does, and this sheet publishes only a flatness row. Plus or minus 0.8 dB in saturation across 450 MHz is useful, but a cascade needs the small signal gain slope at the band edges and the input return loss there, and neither is on the page. At 1.35 GHz and at 1.8 GHz the internal match is doing very different work, and a buyer who plans a single equaliser for both ends is guessing.
There is no compression point, so as with every member of the family the 49 dBm describes a saturated condition and the linear performance of a 450 MHz wideband device is unstated. For a satellite modem with a multi carrier signal that gap is the one that matters most.
There is no bias data, no thermal resistance, no flange drawing and no moisture classification. For a continuous wave part at 79 W the missing thermal figure is the first problem, and the missing bias window is the second, because a 28 V GaN device needs its negative gate present before the drain on every power up.
Where a 79 W wideband L band part still fits
It fits a multi band terminal or a test set that has to cover GNSS L1, Iridium and the Inmarsat uplink in one box, where one device instead of three is worth more than the last dB of gain. It fits a wideband driver for a higher power narrow band stage, and at 37 dBm of drive requirement it is easy to drive from a small signal chain.
It does not fit a continuous wave build without a serious cooling path, and it does not fit a system that needs 56 dBm, where the 1.6 to 1.7 GHz member on 50 V is the correct part. It is also a poor fit for a narrow band application at 1.3 GHz, because the 1.2 to 1.4 GHz members deliver more output and 1 to 2 dB more gain for the same or lower heat.
Our RF power transistor cross reference work records the band edges and the gain at each edge alongside the output, because a 450 MHz part and a 200 MHz part at similar output are not interchangeable in a multi band build, and the flatness figure alone does not tell a buyer where the gain slope goes. The RF component sourcing page sets out how the band specific documentation is handled for parts of this class.
Questions we answer before an order is placed
The first is where in the band the system actually operates. A part specified over 450 MHz gives its worst case somewhere in that span, and a build that uses only the middle 100 MHz should ask for the data at its own frequencies rather than accept the band edge figure. The second is the cooling path, since 79 W in continuous wave is a liquid or forced air decision.
The third is the drive chain at 37 dBm, which is a 5 W stage and the easiest in the family to source. The fourth is the measurement route: RF power and gain against frequency are measured on the customer bench or at a partner RF laboratory, while our own test covers DC parameters, functionality and customer fixtures.
The fifth is the documentation. Ask for the outline drawing, the gain against frequency at the two band edges, the pinch off window and the moisture classification with the quotation. Our incoming inspection plan records the delivered lot against that list, and the request is raised with the vendor before the first lot ships rather than after a first article fails.