HXC40042
Product Specifications
HXC40042
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40042 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40042: twenty five watts at saturation on 9 to 10 GHz with six decibels of gain
The HXC40042 is the largest member of the Hisiwell gallium arsenide internally matched group on 9 to 10 GHz, and like the largest member of the lower window it publishes saturation rather than compression. The index row prints 44 dBm in the saturation column, a gain of at least 6 dB and a drain efficiency of at least 30 per cent, leaves the 1 dB compression column empty, and states 10 V drain, plus or minus 0.8 dB flatness and continuous wave operation. The build is the same as the rest of the group: in-plane matching synthesis, thin film hybrid integration, 50 ohm at both ports.
44 dBm is 25.12 W. Six decibels of gain is the lowest in the family, so the drive at saturation is 38 dBm, which is 6.31 W. That number is the reason this part is usually the last stage of a three amplifier line up rather than a two stage one. At 30 per cent the DC input is 83.73 W, the drain current 8.37 A and the heat 58.61 W.
The window is 1.0 GHz from 9 to 10 GHz, 10.53 per cent fractional at a 9.5 GHz centre. The saturation column being the published one makes this a part for a radar or a continuous wave source that runs near saturation, not for a linear link that needs a stated compression point.
The parameter rows Hisiwell publishes for HXC40042
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 9 to 10 GHz |
| Bandwidth, calculated | 1000 MHz, 10.53 per cent fractional at a 9.5 GHz centre |
| Saturation output power as published | at least 44 dBm |
| Saturation output power in watts, calculated | 25.12 W |
| Output at 1 dB compression as published | not published, the index prints a slash in that column |
| Gain as published | at least 6 dB |
| Drain efficiency as published | at least 30 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the saturation point, calculated | 38 dBm, 6.31 W |
| DC input at saturation, calculated | 83.73 W |
| Drain current at saturation, calculated | 8.37 A at 10 V |
| Dissipation at saturation, calculated | 58.61 W |
| Dissipation if efficiency reaches 40 per cent, calculated | 37.68 W |
| Output per 100 MHz of the band, calculated | 2.51 W |
| Load voltage at saturation into 50 ohm, calculated | 35.44 V RMS, 50.12 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour at 41 dBm compression on the same window | HXC40041, 7 dB gain, 4.20 A, 29.38 W of heat |
| Neighbour at 44 dBm saturation on the lower window | HXC40038, 7 dB gain, 8.5 to 9.6 GHz |
Fifty eight watts of heat in one package
Fifty eight point six one watts is not a number that an extruded heatsink absorbs. At that level the base plate has to spread heat laterally before it reaches the fins, the interface has to be a thin film rather than a pad, and the airflow has to be forced unless the chassis is a large casting. Copper tungsten spreaders and heat pipes appear at this level for a reason.
The current is the other half of the problem. Eight point three seven amps at 10 V means the buck converter is no longer a small circuit, the feed line has to carry the current with an acceptable drop, and the connector and the decoupling have to be chosen for it. A 0.1 V drop on the feed line costs a watt that nobody budgeted.
Pulsed operation changes this arithmetic, but not in a way anyone can quote from the vendor row. At a ten per cent duty the average dissipation falls by a factor of ten and a modest heatsink becomes adequate, while the die still sees the full peak for the length of the pulse. Without a thermal impedance curve the pulse length the part survives cannot be computed, and that document is missing from this part's file.
The efficiency of 30 per cent is a minimum at saturation and there is no compression point figure at all. For a saturated application that is adequate: the part is run where the vendor characterised it. For anything that has to back off, the operating point moves into a region the vendor does not describe, and the efficiency there, and therefore the heat, is unknown.
Saturated service on 9 to 10 GHz
The window covers the maritime radionavigation band at 9.3 to 9.5 GHz, the weather radar allocation near 9.375 GHz, and the short haul links planned into the low end of X band. Twenty five watts at saturation is the shape of a radar transmitter or a high power continuous wave source, not of a linear link amplifier.
Because the part is internally matched across the full gigahertz and presents 50 ohm, a radar front end can be assembled as a chain of packaged parts without a tuned network between them. That is worth a great deal in a production programme, where every tuning step is a fixture and an operator.
For a radar the transmitter usually runs at a fixed duty and a fixed pulse width, which makes the qualification one test rather than a survey. For a continuous wave source there is no relief at all, and the full 58.61 W has to leave the package through the base plate.
For linear service the 41 dBm member of the same window is the right choice: it publishes a compression point, an efficiency at that point, and one more decibel of gain, and it dissipates half the heat. The two parts are not interchangeable even though they sit on the same window.
The ladder at 9 to 10 GHz around HXC40042
Reading from the bottom: 3.98 W with eight decibels of gain, 7.94 W with seven, 12.59 W with seven, and 25.12 W at saturation with six. The gain falls as the periphery grows, so the drive rises faster than the output: from 1.58 W to 2.51 W to 6.31 W. That last step is what turns a two stage line up into a three stage one.
Against the 41 dBm member this part doubles the output at saturation and doubles the heat, and it gives up a decibel of gain and the published compression point. In a radar that runs at saturation the trade is clear. In a link it is not, and the 41 dBm member wins.
The RF power transistor cross reference lists this part against the saturation only member of the lower window, and the RF component sourcing page explains what a saturated line up needs before we quote it.
Questions buyers ask before ordering HXC40042
Is 44 dBm a compression point? No. It is the saturation column. The compression column is empty, so no linear output figure is published for this part.
What is the efficiency at back off? Not published. The 30 per cent figure is stated at saturation, and the vendor gives no curve.
Can it be pulsed? The mode is stated as continuous wave. Pulsed operation is possible in principle but has to be qualified, and the vendor publishes no pulse width, duty cycle or peak current data for this part.
How do we start? Send the saturated output, the duty, the ambient at the base plate, the airflow available and the driver you have. We will confirm the member of the window, quote from the current factory schedule, and ship a sample with the factory test data at the band edges and centre.