HXC40035
Product Specifications
HXC40035
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40035 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40035: thirty six decibels at thirty five per cent on 8.5 to 9.6 GHz
The HXC40035 is a gallium arsenide internally matched power transistor from Hisiwell on a 1.1 GHz window from 8.5 to 9.6 GHz. The vendor states in-plane matching synthesis and thin film hybrid integration, with 50 ohm at both ports, so the part presents a defined impedance at each end of the band without an external match network. The index row reads saturation output not printed, output at 1 dB compression at least 36 dBm, gain at least 8 dB, drain efficiency at least 35 per cent, 10 V drain rail, plus or minus 0.8 dB flatness, continuous wave.
36 dBm is 3.98 W. Eight decibels of gain puts the drive at 28 dBm, which is 0.63 W, a level a small packaged amplifier or a driver stage on the same board can reach. At 35 per cent the DC input is 11.37 W, the drain current 1.14 A and the heat 7.39 W. Those three figures, not the output number, decide the heatsink and the regulator.
The window is 1100 MHz wide, 12.15 per cent fractional at a 9.05 GHz centre. In this internally matched gallium arsenide range only the 5.8 to 6.7 GHz group is wider at 14.40 per cent, and the widest part in the catalogue, the 25.64 per cent high gain member, carries 2.51 W. The plus or minus 0.8 dB is a whole window figure and it is the one a level plan should carry rather than a per channel number.
The parameter rows Hisiwell publishes for HXC40035
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 8.5 to 9.6 GHz |
| Bandwidth, calculated | 1100 MHz, 12.15 per cent fractional at a 9.05 GHz centre |
| Output at 1 dB compression as published | at least 36 dBm |
| Output at 1 dB compression in watts, calculated | 3.98 W |
| Saturation output power as published | not published, the index prints a slash in that column |
| Gain as published | at least 8 dB |
| Drain efficiency as published | at least 35 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the compression point, calculated | 28 dBm, 0.63 W |
| DC input at compression, calculated | 11.37 W |
| Drain current at compression, calculated | 1.14 A at 10 V |
| Dissipation at compression, calculated | 7.39 W |
| Dissipation if efficiency reaches 45 per cent, calculated | 4.86 W |
| Output per 100 MHz of the band, calculated | 0.36 W |
| Load voltage at compression into 50 ohm, calculated | 14.10 V RMS, 19.94 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour on the same window at 39 dBm | HXC40036, 30 per cent, 2.65 A |
| Neighbour on the same window at 41 dBm | HXC40037, 30 per cent, 4.20 A |
The heat side of 3.98 W at 35 per cent
Seven point three nine watts of heat from a part that delivers four watts is the number that shapes the mechanical side of the project. A quarter inch aluminium base with a good interface and still air will not carry that for long; a small extrusion with fins, bolted to the chassis wall, will. The case temperature a buyer should ask us about is the one the vendor does not print, the junction to case thermal resistance, because without it nobody can convert dissipation into a junction temperature.
The rail matters as well. At 1.14 A a linear regulator from a 12 V bus would burn 2.28 W and add it to an already warm package. A buck converter set to 10 V is the usual answer, and the current at that point is low enough that a small inductor and a two amp switch are enough. Whether the bias is sequenced at the gate or fixed by a resistive divider depends on the gate current the vendor does not publish, so a first prototype should allow for both.
The 35 per cent figure is quoted at the compression point, not at the saturated point that the index leaves empty. A backed off operating point below compression will be less efficient, and a drive above compression will produce a higher efficiency at the price of linearity. That trade is fine for a continuous wave source and wrong for anything carrying modulation, so the figure to carry into the budget is the published one and not the one on a curve nobody has seen.
What the 8.5 to 9.6 GHz window covers
X band runs from 8 to 12 GHz and this window sits at the low end of it, covering 8.5 up to 9.6 GHz. The lower part of X band carries maritime radionavigation radar around 9.3 to 9.5 GHz, airborne weather radar near 9.375 GHz, and a large family of short range links and telemetry channels that were built on that plumbing twenty years ago and are still in service.
A buyer with a fixed channel plan inside this window can run one part across the whole plan, which is the reason to pay for an internally matched device rather than buy a bare die and match it. The matching is synthesised in plane and integrated on thin film, so the impedance at the package port is 50 ohm across the 1.1 GHz span and a board can be routed as a fifty ohm line into and out of the part. That removes a tuning step from assembly and removes the fixture that step needs.
What the window does not cover is the upper half of X band. A plan that reaches from 9.5 to 10.5 GHz crosses the boundary between this group and the next one, and no single member on either side spans it. Where the plan is wider than 1.1 GHz, the honest options are two parts with a switch, or the high gain part that covers 8.5 to 11 GHz at 2.51 W, which trades output for coverage.
Where HXC40035 sits in the 8.5 to 9.6 GHz ladder
The window holds four members. This one is the lowest at 36 dBm and the most efficient at 35 per cent, then 39 dBm at 30 per cent, then 41 dBm at 30 per cent, then a saturation only part at 44 dBm whose efficiency column carries a slash. The three compression point members step in three decibel stages, which is a factor of two in power, so a two stage line up built from this part and the 39 dBm member covers 3.98 W to 7.94 W with a single interface between them.
Compared with the 39 dBm member, this part needs 0.63 W of drive rather than 1.26 W and dissipates 7.39 W rather than 18.53 W, which is eleven watts less heat for half the output. In a box that has no room for a fin stack, that difference decides the shape of the whole unit. Compared with the 41 dBm member the gap widens to 22 W of heat and 8.61 W of output.
The RF power transistor cross reference shows the step from one member to the next on the same window, and the one stop RF supply page explains how we hold a line up of this shape on one purchase order across the driver, the final and the passives.
Questions buyers ask before ordering HXC40035
Is 36 dBm the saturation figure? No. It is the output at 1 dB compression, marked as a minimum. The saturation column is empty in the vendor index, so no saturated number is quoted here and none should be carried into a link budget as if it were.
Can it run at 12 V? Not on the vendor rail. The drain voltage is 10 V, and the regulator drop is the buyer's problem to solve. A buck stage is the clean answer at 1.14 A.
What about the flatness across a narrow channel? The plus or minus 0.8 dB is stated over the whole 1.1 GHz window. Over a 100 MHz channel inside it the variation should be smaller, but the vendor publishes no per channel data, so a first article has to measure it in the customer laboratory.
Do you stock it and how do we start? Send the output at the antenna, the modulation, the ambient at the base plate and the rail you have. We will confirm the member of the family that fits, quote from the current factory schedule, and ship a sample with the factory test data at both band edges and the centre.