HXC40030
Product Specifications
HXC40030
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC40030 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC40030: twenty five watts at 35 per cent at 6.4 to 7.2 GHz
The HXC40030 is the largest member of the 6.4 to 7.2 GHz group in the Hisiwell gallium arsenide internally matched family, and it is the part that turns a link budget from marginal into comfortable at this band. The window is 799 MHz, 11.76 per cent fractional at a 6.8 GHz centre, which covers the upper C band fixed service channels and the government allocation above them. The vendor states in-plane matching synthesis and thin film hybrid integration, with 50 ohm at both ports. The index row reads 6.4 to 7.2 GHz, saturation output not printed, output at 1 dB compression at least 44 dBm, gain at least 9 dB, drain efficiency at least 35 per cent, 10 V drain rail, plus or minus 0.8 dB flatness, continuous wave.
44 dBm at compression is 25.12 W. On 10 V the DC input is 71.77 W, the drain current 7.18 A and the heat 46.65 W. The drive is 3.16 W at 35 dBm, which is the same figure the 45 dBm member of the lower band needs, so a driver built for the 5.8 to 6.7 GHz top part carries straight across to this one.
Twenty five watts from a single internally matched device at 6.8 GHz is a different mechanical problem from twelve watts. The 7.18 A feed, the 46.65 W of dissipation and the 35 dBm of drive all have to be solved together, and the part is only usable if the plate under it is a real thermal path rather than a pad on a laminate.
The parameter rows Hisiwell publishes for HXC40030
| Part class | Gallium arsenide internally matched power transistor |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 6.4 to 7.2 GHz |
| Bandwidth, calculated | 799 MHz, 11.76 per cent fractional at a 6.8 GHz centre |
| Output at 1 dB compression as published | at least 44 dBm |
| Output at 1 dB compression in watts, calculated | 25.12 W |
| Saturation output power as published | not published, the index prints a slash in that column |
| Gain as published | at least 9 dB |
| Drain efficiency as published | at least 35 per cent |
| Drain voltage | 10 V |
| Input and output impedance, as stated by the vendor | 50 ohm at both ports |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Drive power for the compression point, calculated | 35 dBm, 3.16 W |
| DC input at compression, calculated | 71.77 W |
| Drain current at compression, calculated | 7.18 A at 10 V |
| Dissipation at compression, calculated | 46.65 W |
| Dissipation if efficiency reaches 50 per cent, calculated | 25.12 W |
| Output per 100 MHz of the band, calculated | 3.14 W |
| Load voltage at compression into 50 ohm, calculated | 35.44 V RMS, 50.12 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, the product page carries one outline image |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour one step below at 41 dBm | HXC40029, 38 per cent, 3.31 A |
| Neighbour on the lower window at 45 dBm | HXC40026, 35 per cent, 9.04 A |
Forty six watts of heat in a 799 MHz window
At 35 per cent, 25.12 W of radio frequency costs 71.77 W of DC input and leaves 46.65 W as heat. That is more than twice the dissipation of the 41 dBm member on the same window, for twice the output, which means the plate has to be sized for the top part even if the product is only ever run at half power. The efficiency does not improve when the part is backed off, so the DC input stays near 70 W for most of the operating range.
The 7.18 A drain current sets the feed. Two parallel wide tracks with vias, or a copper bar, is the usual answer, and the choke has to carry 7.18 A without saturating at the peak of the modulation. At this current the resistance of the feed and the choke is no longer a negligible loss: 10 milliohms in the path costs 0.5 W, and 20 milliohms costs 2 W of extra heat inside an enclosure that is already dissipating 46.65 W.
Thermal interface matters at this level. A 0.2 C per watt interface between the package and a 0.5 C per watt plate puts the case about 32 degrees above ambient at full dissipation, which is why cold plates rather than finned heatsinks are the normal answer at 25 W in a sealed unit.
Upper C band in a real system
In a high capacity point to point link the modulation is dense and the required back off is large, so the delivered power may only be 10 to 12 W from a 25 W part. The DC input barely changes, which means a link that is specified at half the rated output still needs the full thermal stack. That is the single most common surprise when a 44 dBm part is chosen for a 12 W requirement.
In a satellite feeder link or a gateway the same logic holds. The hub controls the transmit power and the amplifier spends most of its life several decibels below compression. The 46.65 W of heat is present anyway, because the drain current on a gallium arsenide device does not fall proportionally with drive.
Linearity is the open question again. The vendor publishes no two tone, no intercept and no adjacent channel data for this part, and at 25 W the linearity of the final stage is what fixes the usable back off. A measurement on the first article, at both band edges, is the only basis for a link budget that depends on a specific modulation.
At 25.12 W a 2 to 1 load reflects about 2.8 W into the output, which is a real load on the die and on the package. An isolator rated for 40 W forward with a 10 W termination is the standard protection in a fixed link, and in a gateway that also has to survive antenna maintenance it is not optional.
Where it sits in the family and on the band
The 6.4 to 7.2 GHz ladder runs 36, 39, 41 and 44 dBm. This is the top, and the step from the 41 dBm member is 3 dB of output for 2.2 times the current and 26.11 W of extra dissipation. Above this there is nothing on the window, so a requirement beyond 25 W is met by combining two of these, which brings its own combiner loss and its own thermal problem.
Across to the lower band, the 45 dBm member covers the same output with 9.04 A and 58.73 W of dissipation instead of 7.18 A and 46.65 W, the difference being the wider band and the lower frequency. A product family that spans both windows can share a driver and a thermal plate and change only the transistor and the small signal parts.
Our RF component sourcing page sets out how we qualify a 25 W stage, and the guide to choosing an RF amplifier covers the single versus combined decision at this power.
Questions buyers ask before ordering HXC40030
Can it be run at 12 V? No. The rail is 10 V and the current is 7.18 A, so a linear regulator would dissipate 14 W before the part even transmits. A 10 V converter rated for 10 A is the practical supply.
Is 44 dBm available across the whole band? The vendor prints at least 44 dBm as the family figure and gives no band edge derating, so the flatness of plus or minus 0.8 dB is the only published variation. Treat the band edges as 43.2 dBm until measured.
What drive does it need? 35 dBm, which is 3.16 W. The same driver used for the 45 dBm lower band part works here, so a shared driver board is feasible across the two windows.
How do we start? Send the output required, the modulation, the ambient at the base plate and the rail available. We will confirm the family member that fits, quote from the current factory schedule and ship a sample with measured output, gain and efficiency across the band.