Contact Us

HXC40003

Brand: Hisiwell
Hisiwell HXC40003 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC40003 — Discrete & Power Semiconductors | Superb Automation

HXC40003

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC40003 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC40003: ten watts of gallium arsenide on a 10 V rail at 1.6 to 1.7 GHz

The HXC40003 is a gallium arsenide internally matched power transistor from Hisiwell. The vendor describes it as built with in-plane matching synthesis and thin film hybrid integration, with 50 ohm at both ports, and its product page names 1.6 to 1.7 GHz as the typical operating window. The index row reads 1.6 to 1.7 GHz, saturation output not printed, output at 1 dB compression at least 40 dBm, gain at least 13 dB, drain efficiency at least 40 per cent, 10 V drain rail, plus or minus 0.8 dB flatness, continuous wave.

40 dBm at compression is 10 W, and the saturation column carries a slash. That distinction matters more than it looks. A part specified at 1 dB compression delivers 10 W while it is still linear to within a decibel and will deliver a little more when pushed; a part specified at saturation delivers 10 W at the point where the gain has collapsed and the waveform is badly distorted. Reading this part as a 10 W saturation device understates it by roughly a decibel, and reading it as a 10 W linear device is close to the truth.

The 10 V rail is the other defining figure. A 10 W GaAs part on 10 V draws 2.5 A at 40 per cent efficiency, which is a higher current than a 28 V GaN part of the same output would draw and a lower voltage that suits a battery product or a 12 V system with a buck converter in front. The trade is current for voltage, and the supply, the cabling and the bias network all follow from it.

The band is 100 MHz wide, 6.06 per cent fractional at a 1.65 GHz centre. That is a channel plan window covering part of the L band used for aeronautical telemetry, some satellite uplinks and downlinks, and several private mobile radio allocations. One part serves the window rather than one channel of it.

The parameter rows Hisiwell publishes for HXC40003

Part classGallium arsenide internally matched power transistor
Matching technique, as stated by the vendorIn-plane matching synthesis, thin film hybrid integration
Frequency range1.6 to 1.7 GHz
Bandwidth, calculated100 MHz, 6.06 per cent fractional at a 1.65 GHz centre
Output at 1 dB compression as publishedat least 40 dBm
Output at 1 dB compression in watts, calculated10.00 W
Saturation output power as publishednot published, the index prints a slash in that column
Gain as publishedat least 13 dB
Drain efficiency as publishedat least 40 per cent
Drain voltage10 V
Input and output impedance50 ohm, matched
Flatness across the bandplus or minus 0.8 dB
Operating modecontinuous wave
Drive power for the compression point, calculated27 dBm, 501 mW
DC input at compression, calculated25.00 W
Drain current at compression, calculated2.50 A at 10 V
Dissipation at compression, calculated15.00 W
Dissipation if efficiency reaches 60 per cent, calculated6.67 W
Output per 100 MHz of the band, calculated10.00 W
Load voltage at compression into 50 ohm, calculated22.36 V RMS, 31.62 V peak
Thermal resistance, junction to casenot published
Package outline and dimensionsnot published in text
Scattering parametersnot published
Gate bias point and quiescent currentnot published
Operating and storage temperaturenot published
Orderable addendum, marking and packingnot published
Neighbour on the same rail at 42 dBm compression on 2.0 to 2.2 GHzHXC40004, 11 dB gain

What 2.5 amperes at 10 volts means for the supply

2.5 A at 10 V is more awkward than 0.9 A at 28 V, even though the power is the same. The current sets the track width, the connector rating and the size of the bulk capacitor, and the 10 V rail is usually generated by a buck converter that has its own loop bandwidth. A transmitter that pulses the drain current at the waveform rate can push that converter into a transient it was never specified for.

The bias network has to isolate the two. A local bulk capacitor of a few hundred microfarads at the drain feed, a ferrite bead and a short wide track back to the regulator are the usual answer. The vendor publishes no quiescent current and no gate voltage window, so the bias point is found on the bench and recorded, and the setting becomes part of the build instruction rather than something the assembler guesses.

15 W of dissipation at compression is a moderate heat load. On a 3 C per watt carrier the case rise is 45 C, which leaves room for a 25 C base plate and a junction that the vendor does not publish. On 1 C per watt it is 15 C and the part runs cool. The carrier choice can be modest here, unlike the sixteen watt X band module where the same dissipation has to leave a much smaller flange.

The efficiency figure is quoted at the compression point rather than at saturation. Forty per cent at 1 dB compression is a reasonable GaAs figure and it is not directly comparable with a GaN saturation efficiency of 60 per cent. A system that compares parts on the efficiency column without noting which output point the number belongs to will choose wrongly, usually in favour of the part with the better number at the less demanding point.

The gain budget at 13 decibels

13 dB of gain means 500 mW of drive for 10 W of output. That is a real driver, and it is the reason this part sits behind a gain block rather than directly behind a modulator. A two stage line with a 27 dBm driver and this part delivers 40 dBm with about 26 dB of total gain, which is enough for most L band transmitters with a few decibels in hand.

Thirteen decibels is also low enough that the input match is less critical than it would be on a 28 dB module. A three decibel mismatch at the input costs a tenth of a decibel of drive rather than a third of it, and the driver is less likely to be pulled by the load. That is one practical advantage of a lower gain part in a chain that has a fixed driver.

The plus or minus 0.8 dB flatness figure is published, which is more than most parts in this catalogue give. It is a band edge specification and it applies across 100 MHz. A system with a level control loop can work with a wider figure, and a system with a fixed level plan will value the published number because it can be budgeted rather than measured.

At 1 dB compression the part is still linear to within a decibel. For a single carrier constant envelope waveform that is the normal operating point. For a multi-carrier or high order modulation waveform the part has to be backed off, and the useful back off is set by the third order intercept, which the vendor does not publish. That figure has to be measured on a two tone test before a linear application is committed.

Where 1.6 to 1.7 GHz is used

The window sits in the L band. Aeronautical telemetry in several regions uses 1.6 to 1.7 GHz links, satellite mobile services use overlapping allocations, and private mobile radio and utility telemetry systems use channels inside it. The common thread is a moderate power transmitter with a modest antenna, where 10 W at the connector is enough to close a link over tens of kilometres with a small directional antenna.

In a telemetry transmitter the part is usually driven by a shaped waveform and run near compression, because the modulation is constant envelope and the spectrum is controlled by the modulator rather than by the amplifier linearity. That is the easiest application for this part and the one the published figures support.

In a satellite terminal the same part may serve the uplink, where the output has to stay linear and the drive has to be controlled to protect the satellite. That application needs the two tone data and a thermal sweep, because the compression point moves with temperature and the vendor publishes no curve.

Our RF component sourcing page explains how we qualify a part for this kind of application, and it lists the measurements we ask for before a build is committed to a single source.

Comparing HXC40003 with its neighbours and with the GaN parts

The HXC40004 covers 2.0 to 2.2 GHz at 42 dBm compression with 11 dB of gain on the same 10 V rail, so the family steps up in frequency with slightly less gain and slightly more output. The HXC40006 covers 2.7 to 3.4 GHz at 37 dBm saturation with 12 dB of gain, and the HXC40007 covers 3.1 to 3.5 GHz at 42 dBm saturation with 10.5 dB. Each member covers a distinct window and none of them overlaps this one much.

On the GaN side the closest parts run on 28 V and offer more gain. The HXN40007 covers 1.35 to 1.8 GHz at 49 dBm with 12 dB of gain and 50 per cent efficiency, which is ten times the output of this part on a higher rail. A GaN part with a 28 V supply and a 12 dB gain figure is not a drop in replacement for a 10 V GaAs part in a battery product, and the rail decides the family before the output does.

For an obsolete part replacement, the sequence is rail, then band, then output point, then gain. A part quoted at 1 dB compression cannot be matched against a part quoted at saturation without adjusting for the difference, and that adjustment is usually between half a decibel and one and a half decibels. Our obsolete RF part replacement page sets out how that comparison is made and what we ask for when the original data sheet is no longer available.

Questions buyers ask before ordering HXC40003

Is the 40 dBm a saturation or a compression figure? It is 1 dB compression. The saturation column carries a slash. If a system needs a saturation number, it has to be measured, and the measured value is normally one decibel or so above the compression figure.

Is there a data sheet? No. The vendor publishes an index row and a product page with the same four electrical figures and the 50 ohm port impedance. There are no curves, no scattering parameters, no thermal data and no package drawing.

What has to be on the purchase order? The band, the 10 V rail, the continuous wave mode and the quantity. No orderable addendum, marking code or packing column is published, so reel size and moisture level come from the factory quotation.

How do we start? Send the band, the output point that matters to the system, the drive available and the rail. We will confirm whether this part or a neighbour fits, quote from the current factory schedule and ship a sample with measured output at compression and gain at the band edges.