Contact Us

HX2040185F

Brand: Hisiwell
Hisiwell HX2040185F is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HX2040185F — Discrete & Power Semiconductors | Superb Automation

HX2040185F

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HX2040185F from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HX2040185F: one hundred and eighty five watts on 2 to 4 GHz with a fifty point nine dBm row underneath

The HX2040185F is a gallium nitride RF power transistor from Hisiwell for the 2 to 4 GHz window on a 28 or 48 V rail. The overview calls it a 185 W part. The family index prints 185 W of saturation output with 18 dB of gain and 70 per cent drain efficiency. The parameter block on the product page prints a maximum saturated power of 50.9 dBm and a best drain efficiency of 72.5 per cent, and 50.9 dBm is 123.0 W, not 185 W.

That is a 1.77 dB gap between two numbers on the same page. Neither is marked as a minimum and neither is marked as typical, so the page carries both: 185 W from the index and the overview, 123 W from the parameter block, and the note that the factory has to say which one the lot is screened to. A buyer sizing a heatsink on 185 W and receiving a 123 W part has a margin problem in the other direction, so the gap matters both ways.

One hundred and eighty five watts is 52.67 dBm. With 18 dB of gain the drive is 34.67 dBm, which is 2.93 W. At 70 per cent drain efficiency the DC input is 264.3 W, the drain current is 9.44 A at 28 V or 5.51 A at 48 V, and the heat is 79.3 W. At the 123 W reading and 72.5 per cent the DC input is 169.7 W, the current is 6.06 A at 28 V and the heat is 46.7 W.

Two gigahertz of band at 185 W is 92.5 W per gigahertz, which is lower density than the 1 to 2 GHz pair at 140 and 280 W per gigahertz. That is expected: the match is harder at 4 GHz, and the efficiency falls from 80 to 70 per cent for the same reason.

The parameter rows behind the HX2040185F

Part classGallium nitride RF power transistor, unmatched
Frequency range2 to 4 GHz
Saturation output, index row185 W
Power in the overview sentence185 W
Maximum saturated power, parameter block50.9 dBm, which is 123.0 W
Gap between the two readings, calculated1.77 dB
Power in dBm at 185 W, calculated52.67 dBm
Power gain18 dB
Drive power at 185 W, calculated34.67 dBm, 2.93 W
Drive power at 123 W, calculated32.90 dBm, 1.95 W
Drain efficiency, index row70 per cent
Best drain efficiency, parameter block72.5 per cent
DC input at 70 per cent, calculated264.3 W
Drain current at 28 V, calculated9.44 A
Drain current at 48 V, calculated5.51 A
Dissipation at 185 W, calculated79.3 W on either rail
DC input at 123 W and 72.5 per cent, calculated169.7 W, 6.06 A, 46.7 W of heat
Supply rails28 V or 48 V
Operating modeContinuous wave
Load voltage at 50 ohm, calculated96.2 V RMS, 136.0 V peak at 185 W
Load voltage under a two to one mismatch, calculatedabout 192 V peak
Output per GHz of band, calculated92.5 W per GHz
MatchingUnmatched, external network on the customer board
Body and packageNot published
Thermal resistance, junction to caseNot published
Input and output impedanceNot published in text
Gate bias point and quiescent currentNot published
Orderable addendum, marking and packingNot published

Nine amps on the drain and seventy nine watts to remove

The 28 V route draws 9.44 A and the 48 V route draws 5.51 A for the same output. Both dissipate 79.3 W, so the second rail buys DC copper and choke size and nothing else. On a 2 to 4 GHz board, where the copper under the match is already thick to keep the loss down, that trade is less valuable than it is at 1 GHz, and a 28 V rail is common.

Seventy nine watts is past the range of a finned block in free air. At a 0.3 degree per watt sink and a 0.1 degree per watt interface the rise is about 32 degrees, which a forced air sink holds and a passive one does not. The case temperature is measured rather than derived, because the vendor publishes no junction to case resistance.

The output match at 2 to 4 GHz is a distributed structure rather than a lumped ladder. Two gigahertz of band at this frequency is more than an octave, and the parasitics of the device are a substantial part of the match, so the network is tuned on the board with the device in place rather than computed and then built. That is why a reference board from the factory is worth more here than at 1 GHz.

The 136 V peak matched and 192 V peak under a two to one mismatch put the output capacitors in the 250 to 500 V class. At 4 GHz the same capacitance has to hold its Q, so the choice is a porcelain or a thin film part rather than a high K ceramic.

HX2040185F against the higher band shelves

HX2040185F2 to 4 GHz185 W18 dB70 per centReference point
HX1020240P21 to 2 GHz280 W20 dB80 per cent1.80 dB above, lower band
HX1020120P21 to 2 GHz140 W20 dB80 per cent1.21 dB below, lower band
HXN502452.7 to 3.5 GHz200 WNot publishedNot published0.34 dB above, pulse row
HXN502403 to 4.2 GHz200 WNot publishedNot published0.34 dB above, CW row
HX446050F24.4 to 6 GHz50 W15 dB55 per cent5.68 dB below, upper band

The 2 to 4 GHz window sits between two families. The 1 to 2 GHz pair gives more output and better efficiency but stops at 2 GHz, and the 2.7 to 4.2 GHz members of the HXN group give slightly more output in narrower windows with no published gain or efficiency at all.

That makes this part the only member that covers the whole 2 to 4 GHz window with a published gain, a published efficiency and a rail option. For a wideband amplifier that has to sweep 2 to 4 GHz, that combination is the reason to buy it, and the missing 1.77 dB between its two power figures is a question to settle rather than a reason to walk away.

Where the band is narrow, the HXN50240 at 3 to 4.2 GHz gives 0.34 dB more output, and the RF power transistor cross reference shows where the two overlap. When the gain and efficiency rows are needed for a model, RF component sourcing covers how a measured set is obtained with the order.

Board notes for a two to four gigahertz stage

The board material is the first item. At 4 GHz the loss of the laminate is a real part of the budget, and the dielectric thickness sets the impedance of every distributed element in the match. A material change after the match is tuned is a full retune, so the stack is fixed before the first board is cut.

The bias is the second item. No gate voltage and no quiescent current is published for this part. A 28 V GaN device at class AB draws a quiescent current that has to be temperature compensated, and at 4 GHz the bias network itself has to be kept out of the RF path with a low inductance choke.

The sequencer is the third item. Negative gate before drain, drain off before gate, clamp at the gate. At 9.4 A of drain current the failure from a floating gate takes microseconds and leaves no diagnostic trace beyond a shorted die.

The thermal and mechanical interface is the fourth. A flanged or over moulded body at 79 W wants a torque specification, a flatness figure and a thermal compound with a known thickness. All three are absent from the vendor text, so the first article is where they are established.

Questions buyers ask about HX2040185F

Is it 185 W or 123 W? The index row and the overview say 185 W, the parameter block says 50.9 dBm which is 123 W. We quote 185 W and state the second figure, and we ask the factory which one the lot is screened to before a schedule is set.

Which rail should we use? Both 28 and 48 V appear in the overview. The heat is identical on either, so the choice is DC current and choke size against the higher voltage rating of the passives.

What is the drive? 2.93 W at 185 W with 18 dB of gain, and 1.95 W at 123 W. Either way the stage in front is a power amplifier rather than a small signal part.

Does it cover the whole 2 to 4 GHz window? Yes, that is the band stated in the index and in the overview, and the 70 per cent efficiency is quoted for the band rather than for a single frequency in the text.

How do we start? Send the band, the rail, the output at the connector, the signal and the ambient. We will confirm the power figure for the current lot, quote from the schedule and ship a sample with the gain and the efficiency measured at 2.0, 3.0 and 4.0 GHz.