HX1020240P2
Product Specifications
HX1020240P2
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HX1020240P2 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HX1020240P2: two hundred and eighty watts on one gigahertz and a parameter block that came from its neighbour
The HX1020240P2 is the high power member of the Hisiwell 1 to 2 GHz pair, a gallium nitride RF power transistor on a 28 or 48 V rail. The overview sentence calls it a 240 W part. The family index prints 280 W of saturation output with 20 dB of gain and 80 per cent drain efficiency. The parameter block on the product page prints a maximum saturated power of 155 W and a best drain efficiency of 81.1 per cent, which are the exact figures printed on the page of its 140 W neighbour.
That last point is not a rounding difference, it is a copy. The same two numbers, 155 W and 81.1 per cent, sit on the HX1020120P2 page. The most likely reading is that the parameter block was duplicated when the page was built, and the honest treatment is to say so and to work from the index row and the overview sentence, both of which put this part above 240 W.
Two hundred and eighty watts is 54.47 dBm and 240 W is 53.80 dBm. With 20 dB of gain the drive at 280 W is 34.47 dBm, which is 2.80 W, and at 240 W it is 2.40 W. Either figure needs a driver stage with its own rail and its own heatsink, which is the point at which a 1 to 2 GHz line up stops being a two stage build.
The rail is the other decision. On 28 V, 280 W at 80 per cent draws 12.5 A. On 48 V the same output draws 7.29 A. The heat is 70 W either way, so the second rail buys current and copper rather than thermal margin, and that is exactly what a 280 W board needs.
The parameter rows behind the HX1020240P2
| Part class | Gallium nitride RF power transistor, unmatched |
| Frequency range | 1 to 2 GHz |
| Saturation output, index row | 280 W |
| Power in the overview sentence | 240 W |
| Maximum saturated power, product parameter block | 155 W, the same value printed on the 140 W neighbour |
| Power in dBm, calculated | 54.47 dBm at 280 W, 53.80 dBm at 240 W |
| Spread between the index and the overview | 0.67 dB |
| Power gain | 20 dB |
| Drive power at 280 W, calculated | 34.47 dBm, 2.80 W |
| Drive power at 240 W, calculated | 33.80 dBm, 2.40 W |
| Drain efficiency, index row | 80 per cent |
| Best drain efficiency, parameter block | 81.1 per cent, the same value printed on the neighbour |
| DC input at 80 per cent, calculated | 350.0 W |
| Drain current at 28 V, calculated | 12.50 A |
| Drain current at 48 V, calculated | 7.29 A |
| Dissipation at saturation, calculated | 70.0 W on either rail |
| Supply rails | 28 V or 48 V |
| Operating mode | Continuous wave |
| Load voltage at 50 ohm, calculated | 118.3 V RMS, 167.3 V peak at 280 W |
| Load voltage at 240 W, calculated | 109.5 V RMS, 154.9 V peak |
| Load voltage under a two to one mismatch, calculated | about 237 V peak at 280 W |
| Output per GHz of band, calculated | 280 W per GHz |
| Matching | Unmatched, external network on the customer board |
| Body and package | Not published |
| Thermal resistance, junction to case | Not published |
| Input and output impedance | Not published in text |
| Gate bias point and quiescent current | Not published |
| Orderable addendum, marking and packing | Not published |
Twelve and a half amps on 28 volts against seven and a quarter on 48
Twelve and a half amps at 28 V is a copper pour rather than a trace. At one ounce, a 350 mil run carries it with a rise that stays inside the usual window, and the drain choke and the bulk bank sit on the same pound of copper. On 48 V the same output draws 7.29 A, which is a 175 mil run, and the choke is smaller because the current is smaller.
The 48 V rail has a cost of its own. The bias supply has to be sequenced the same way, the gate clamp has to hold at the higher rail, and the bulk capacitors need a higher voltage rating, which raises their ESR and their size for the same capacitance. The decision is not automatic; it is a trade of DC copper against passive volume.
Seventy watts of heat in either case. That is a liquid plate or a forced air sink with a large face, and it is well past what a finned block in free air can hold. The interface between the device and the sink is where the build is won or lost, because 70 W through a bad interface at 1.5 degree per watt adds 105 degrees, which is above any junction limit.
At the output, 167.3 V peak matched and about 237 V peak under a two to one mismatch. That puts the output network in a different component class: 500 V porcelain or thin film capacitors, and a series element rated for the full RF current at that voltage. The bill of materials for a 280 W match is not a scaled version of the 140 W one.
HX1020240P2 against the one gigahertz pair and the shelf
| HX1020120P2 | 1 to 2 GHz | 140 W | 20 dB | 80 per cent | 3.01 dB below, 28 V only |
| HX1020240P2 | 1 to 2 GHz | 280 W | 20 dB | 80 per cent | Reference point, 28 or 48 V |
| HXN50256 | 0.7 to 2.7 GHz | 120 W peak | Not published | Not published | 3.68 dB below, 1.7 GHz wider |
| HX2040185F | 2 to 4 GHz | 185 W | 18 dB | 70 per cent | 1.80 dB below, different band |
| HXN50240 | 3 to 4.2 GHz | 200 W | Not published | Not published | 1.46 dB below, different band |
| HX5060140P2 | 5 to 6 GHz | 140 W | 11 dB | 50 per cent | 3.01 dB below, different band |
The pair of 1 to 2 GHz parts are the same die family and the same gain, 3.01 dB apart, and the 280 W member is the only one that offers a 48 V rail. A product with a 48 V bus can use it directly; a product with a 28 V bus has to decide whether 12.5 A of DC current is easier than a second converter.
Against the higher bands the choice is band, not power. The HX2040185F covers 2 to 4 GHz at 185 W with a published 18 dB of gain and 70 per cent efficiency, and it is 1.8 dB below this part with far better published data. Where the data matters more than the last 2 dB, that is the part to build.
For a 1 to 2 GHz radar or a test amplifier that has to run continuous wave, both members of the pair are on the same shelf and the RF power transistor cross reference puts them side by side with the rail options. Where the schedule is long on one member, component lead time solutions covers the backing off route from the larger part.
Board notes for two hundred and eighty watts on a narrow band
The match is the first item. One gigahertz of band at 280 W wants a low pass ladder with series elements that carry the full RF current, and at 167 V peak the capacitors have to be 500 V class. The board material has to hold its dielectric constant under the temperature the match reaches, which for a narrow band network on a hot sink is a real constraint rather than a specification exercise.
The rail is the second item. If 48 V is chosen, the drain bypass has to handle the higher voltage and the sequencer has to clamp the gate at a level that is safe for the higher rail. If 28 V is chosen, the copper and the choke are the constraint. Neither route is free, and the choice is made before the board is ordered rather than after.
The bias is the third item. No gate voltage and no quiescent current is published. Class AB at 280 W draws a quiescent current in the amps, and the bias supply has to hold that current without drifting as the case temperature rises. A temperature compensated bias network is normal at this power; a fixed divider is not.
The fourth item is the interface. With 70 W of heat and no published thermal resistance, the case temperature at rated output in the final enclosure is the only closure. It is measured on the first article and written into the test report, and the acceptance limit is fixed before the measurement.
Questions buyers ask about HX1020240P2
Is the parameter block correct? The 155 W and 81.1 per cent printed there are the same values as the 140 W neighbour, so we treat the block as a copy and work from the index row at 280 W and the overview at 240 W. The factory is asked to confirm the number the lot is screened to.
Does it need 48 V? No, the index row states 28 V and the overview states 28 or 48. The 48 V option is the reason to pick this part over the 140 W member if the DC current is the constraint.
What is the drive? At 20 dB of gain, 2.80 W at 280 W and 2.40 W at 240 W. That is a small amplifier in its own right, with its own heat, so the line up is three stages rather than two.
Is it linear enough for a modulated signal? No compression point is published. The 80 per cent is a saturation figure, and a backed off operating point has to be measured on the first article.
How do we start? Send the rail, the band edges, the output at the connector, the signal and the ambient. We will confirm the power figure for the current lot, quote from the schedule and ship a sample with gain, efficiency and the case temperature recorded at the band centre.