MAX985EUK+T
Product Specifications
MAX985EUK+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX985EUK+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX985EUK+T: 11 uA comparator with a 300 ns delay
The MAX985EUK+T is the single micropower comparator of the MAX985/MAX986/MAX989/MAX990/MAX993/MAX994 family in the 5 pin SOT23. It operates from 2.5 V to 5.5 V single ended or plus or minus 1.25 V to plus or minus 2.75 V dual, draws 11 uA, and delivers 300 ns of propagation delay with rail-to-rail inputs and outputs. The input common mode extends 250 mV beyond both rails, the input bias current is 1.0 pA typical, the offset is 0.5 mV typical, and the push-pull output sinks and sources 8 mA. It is on the analog and mixed-signal IC line card.
Eleven microamps changes what a comparator can be left on for
Eleven microamps at 3.3 V is 36.3 uW and 96.4 mAh over a year, which is small enough that the comparator can stay powered in a battery product instead of being gated. That is the point of the part: 300 ns of delay is 3.33 MHz of equivalent edge rate, fast enough for a level detector on a control loop, at a current that a coin cell can supply for years. The vendor also quotes 80 uA at 1 MHz of switching, which is the figure that applies when the output toggles continuously rather than sitting at a level.
| Parameter | Figure | Meaning |
|---|---|---|
| Supply current | 11 uA | 36.3 uW at 3.3 V, 96.4 mAh over a year |
| Propagation delay | 300 ns | 3.33 MHz equivalent |
| Input bias current | 1.0 pA typical | offset dominates until the source passes 500 Mohm |
| Input offset | 0.5 mV typical | 1 pA through 500 Mohm is the same 0.5 mV |
| Common mode | 250 mV beyond both rails | a signal above the rail does not latch the input |
| Output drive | 8 mA push-pull | 0.80 V into 100 ohm, the load sets the swing |
Offset against bias current, and the crossover
The two input errors cross at 500 Mohm, where 1 pA produces 0.5 mV, the same as the offset. Below that the offset is the limit and the pA bias figure is decoration; above it the bias takes over and the low bias becomes the reason to choose the part. This is the same arithmetic that decides a photodiode or pH electrode front end, and it is why the family is specified with both numbers rather than just the offset.
Selection notes
- This is the push-pull member. The MAX986, MAX990 and MAX994 have open-drain outputs that can be pulled above VCC to 6 V, which is what a level translator or a wired-OR needs. The two output styles are not interchangeable on a shared bus.
- Internal hysteresis is stated without a number. For a slow input the hysteresis band, not the 300 ns, sets the jitter at the trip point, so measure it on the first article where edge timing matters.
- No phase reversal on overdriven inputs, so an input driven past either rail does not invert the output. That is what makes the 250 mV beyond the rails useful rather than a rating on paper.
- The output stage limits switching current surges, which the vendor presents as a supply glitch reduction. On a shared analog rail that is worth more than the 11 uA.
Where it fits
Battery products, threshold and level detectors, window comparators built from two parts, zero-crossing detectors and any supervisory function that has to run from a rail too small to spare a milliamp. The SOT23 body and the UCSP option cover both a hand assembled prototype and a dense wearable.
Board notes for a picoamp input
One picoamp of bias current is smaller than the leakage of a contaminated board. Guard the input node, keep the trace short, clean the assembly and avoid solder flux that leaves a resistive film. The 250 mV beyond-the-rails input range helps with a sensor whose output can exceed the rail, but the absolute maximum still applies and a series resistor is the cheap protection. The push-pull output drives 8 mA, which is 0.80 V into 100 ohm, so the load resistor sets the swing rather than the comparator. Where the part drives a CMOS input with a slow edge, the internal hysteresis keeps the output clean; where it drives a long cable, a series resistor at the source is the usual fix.
Questions buyers ask
Is the EUK suffix the SOT23? It is the 5 pin SOT23 ordering code for the single. The UCSP body is a different code and a different footprint.
Can it run from a 1.8 V rail? No. The minimum is 2.5 V single ended; a 1.8 V system needs a different comparator family.
What does a quote need? The order code, the rail voltage, the output style, push-pull or open-drain, and the annual quantity. Send it to the signal chain cross reference desk; where the line is short, the desk checks a pin to pin candidate for the output style and the common mode range, because those two are what a substitution usually changes.
Request Quote — In Stock, 100% New & Original, Full Warranty