Contact Us

MAX9648AXK+T

Brand: Analog Devices
Analog Devices MAX9648AXK+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX9648AXK+T — Analog & Mixed-Signal ICs | Superb Automation

MAX9648AXK+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX9648AXK+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX9648AXK+T: 60 uA, 2 mV of Hysteresis and a SC70 That Replaces an LMX331

The MAX9648AXK+T is a single general purpose comparator in a 5-pin SC70 measuring 2.0 mm by 2.1 mm by 1.0 mm, guaranteed from 1.8 V to 5.5 V over minus 40 to 125 C, drawing 60 uA per channel at a 5 V supply. Its input common mode range includes ground, it does not phase invert when the input is overdriven, the output saturation voltage is 120 mV, and it has 2 mV of internal hysteresis that suppresses output chatter on a slow moving input. It is a pin for pin replacement for the LMX331 and LMX331H, and the MAX9647 is the same comparator without the hysteresis.

This is the part chosen for a battery product that has to detect a threshold with a fraction of a milliamp and has no room for a comparator plus external positive feedback. The internal hysteresis is the feature that removes the two resistors a conventional threshold detector needs, and it is also the feature that most often gets lost in a substitution.

Two millivolts of hysteresis is 0.061 percent of a 3.3 V rail

A 2 mV window is small in absolute terms and is exactly the right size for a threshold detector on a 3.3 V rail crossed by a slow signal: it is 0.061 percent of the rail, so a supply that moves by a few millivolts does not fire the comparator twice, and a signal that has to be detected within tens of millivolts is not delayed by more than the window. Set against a comparator with no hysteresis, the difference is visible in the output: a slow input with 5 mV of noise crosses the threshold many times and produces a burst of edges at every crossing, and every one of those edges is an interrupt in the controller.

Sixty microamps at 5 V is 300 uW and at 1.8 V is 108 uW, which over a year is 525.6 mAh at the higher rail. That is small enough to leave on continuously in a product with a coin cell, and it is why the part is specified down to 1.8 V: a two cell alkaline product spends most of its life below 3 V, and a comparator with a 2.7 V minimum would stop working halfway through the discharge curve.

Supply1.8 V to 5.5 V guaranteed, 60 uA at 5 V, 300 uW
Annual current525.6 mAh at 60 uA, small enough for continuous operation
Hysteresis2 mV internal, 0.061 percent of a 3.3 V rail
Input rangeIncludes ground, no phase reversal on overdrive
Output low120 mV saturation, 280 mV below a 0.4 V logic low limit
ReplacementPin for pin for the LMX331 and LMX331H
TemperatureMinus 40 to 125 C, automotive range
Package5-pin SC70, 2.0 mm by 2.1 mm by 1.0 mm, also SOT-23 as AUK
FamilyMAX9647 is the same comparator without internal hysteresis
ApplicationThreshold detection, battery monitors, portable instruments

The 120 mV output is the number to check against the logic it drives

At 120 mV of saturation the output is comfortably below a 0.4 V logic low limit at any supply, with 280 mV of margin, so it drives a CMOS input directly without a pull-up. What it does not do is wired-OR: the output stage is a push-pull arrangement described by its saturation voltage, so two comparators cannot share a line and a circuit that relied on open-drain behaviour needs a different part. That difference is invisible in a one line catalogue description and is the reason a comparator substitution fails on a shared interrupt line.

The ground-sensing input matters more than the hysteresis in a current sense application. A low side shunt at the bottom of a load produces a signal that starts at zero and rises, and a comparator whose input range stops a few hundred millivolts above ground cannot see the first part of that ramp at all. With the input range including ground and no phase inversion on overdrive, the same part works for a signal that goes below ground during a transient without producing a false edge.

Two questions buyers ask

What is the difference between the MAX9647 and the MAX9648?
The hysteresis. The MAX9648 has 2 mV of internal hysteresis, the MAX9647 has none, and both are otherwise the same comparator in the same packages. A circuit that added external positive feedback around a MAX9647 can use a MAX9648 and delete two resistors; a circuit that needs a precise threshold with no window at all needs the MAX9647 and its external network.

Does the SC70 version have the same limits as the SOT-23?
Yes, the electrical table is the same and the difference is the body. The AUK suffix is the SOT-23 and the AXK suffix is the SC70, and both are specified over the same temperature range. The choice is made by the board area and the assembly process rather than by a specification, and a 5-pin SC70 at 0.65 mm pitch needs a stencil and a reflow profile that a 1.9 mm pitch SOT-23 does not.

Ordering and supply

The AXK suffix is the 5-pin SC70 and the T suffix is tape and reel. Substitution traps are the hysteresis, the output structure and the minimum supply. A part with a 2.7 V minimum cannot finish a two cell alkaline discharge curve, a part without hysteresis will chatter on a slow input, and an open-drain part in a push-pull socket leaves a line that never goes high without an external pull-up.

We hold and source this family for production and for repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the pin to pin cross reference, and where a comparator has to be replaced on a built board, the steps in how to verify a drop in replacement cover the hysteresis and the output structure before the threshold is measured.

Request Quote — In Stock, 100% New & Original, Full Warranty