MAX813LMJA
Product Specifications
MAX813LMJA
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX813LMJA from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX813LMJA: A 4.65 V Threshold, a 200 ms Reset and an Active-High Output
The MAX813LMJA is a microprocessor supervisory circuit in the MAX705 to MAX813L family, in the 8-pin ceramic dual in line package on the military temperature grade. It provides four functions in one part: a reset output held for 200 ms after the supply comes up, an independent watchdog that pulls its output low if the watchdog input has not been toggled within 1.6 s, a 1.25 V threshold comparator for power-fail warning or low battery detection, and a debounced manual reset input. The supply monitor trips at 4.65 V on this member, the active-low reset output is guaranteed valid down to a 1 V supply, and the part is specified over the full military temperature range with the ceramic package offering the thermal and hermetic properties that grade requires.
The MAX813L is the member with an active-high reset output rather than an active-low one, which is the single most important thing to know before it goes into a socket built for a MAX705. Everything else on the first page is identical, and the two parts are otherwise the same function.
4.65 V against a 5 V rail with a 10 percent tolerance is the wrong threshold
A 4.65 V trip point sits 100 mV below a 5 V rail at minus 5 percent, which is 4.75 V, so a supply that sags to the bottom of a 5 percent window is still 100 mV above the trip and the part behaves. On a rail specified at plus or minus 10 percent, the legal minimum is 4.5 V, which is 150 mV below the trip: the supervisor has already asserted reset while the supply is still inside its own specification. A product built that way resets itself on a legal supply, and the fault is usually blamed on the power supply rather than on the threshold. The 4.40 V member of the same family is the correct part for a 10 percent rail, with 100 mV of margin below 4.5 V.
The 200 ms reset pulse and the 1.6 s watchdog are both long compared with a typical microcontroller clock. At a 20 ms housekeeping tick the reset is 10 ticks and the watchdog 80 ticks, so the firmware has 80 chances to service the watchdog before it fires, and a reset takes 10 housekeeping cycles to release. That ratio is what makes the part usable with a slow, low power controller: the watchdog does not fire during a legitimate long computation and the reset does not release before the oscillator is stable.
| Supply threshold | 4.65 V, which is 93 percent of a 5 V rail |
| Margin at minus 5 percent | 100 mV below 4.75 V |
| Margin at minus 10 percent | Asserts before a legal 4.5 V rail is reached, by 150 mV |
| Reset pulse | 200 ms, 10 ticks of a 20 ms housekeeping loop |
| Watchdog | 1.6 s, 80 ticks of the same loop, output goes low if not serviced |
| Reset polarity | Active high on this part, active low on the MAX705 |
| Low supply behaviour | Active-low reset guaranteed valid down to 1 V |
| Auxiliary comparator | 1.25 V threshold for power-fail or low battery, external divider |
| Manual reset | Debounced TTL and CMOS compatible input |
| Package | 8-pin ceramic DIP, military temperature grade |
The active-high output is the substitution trap in this family
An active-high reset goes low during a reset and high when the part is running, which is the opposite of what most microcontroller reset pins expect. A board that receives an active-high part in an active-low socket is held out of reset permanently while the supply is good, and the microcontroller runs through every brownout with no reset at all: the failure is intermittent behaviour under a sagging supply, not a dead board, which is the hardest kind of fault to trace. The MAX707, MAX708 and MAX813L carry the active-high output, and the MAX705 and MAX706 the active-low one.
The 1.25 V comparator is independent of the supply monitor and is the part that gets forgotten in a bill of materials review. It can watch a second rail, a battery, or a rectified input ahead of the regulator through a two resistor divider, and it is the only early warning the system gets before the main supply crosses its own threshold. Where it is left unconnected the power-fail interrupt never fires and the product loses the time it needs to store state.
Two questions buyers ask
Can the auxiliary comparator watch a 12 V rail?
Yes, with a divider. The 1.25 V threshold divided into a 12 V rail needs a ratio of 0.104, which a pair of 1 percent resistors sets closely; at a total divider resistance of 1 MOhm the current is 12 uA, which is negligible next to the supply current of the product. The tolerance of the trip point is then the resistor tolerance plus the comparator offset rather than the reference, so 1 percent resistors give a trip accuracy of about 1.6 percent.
Is the ceramic package electrically different from the plastic one?
The die is the same family, but the order code carries the temperature grade and the package, and the military grade is tested to its own table over the extended range. A ceramic part is bought for the range and the hermeticity, not for a different function, and the electrical limits quoted in the commercial table do not automatically apply to it.
Ordering and supply
The MJA suffix is the 8-pin ceramic dual in line package on the military grade. The traps in this family are the reset polarity, the threshold option and the package grade: three letters in the order code change all three. A MAX813L in a MAX705 socket inverts the reset, a 4.65 V part in a 10 percent rail resets on a legal supply, and a plastic part in a military build fails the qualification before it fails in the field.
We hold and source this family for production and for repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the power management cross reference, and where a supervisor has to be changed on a board that is already built, the order in how to verify a drop in replacement puts the reset polarity and the threshold ahead of the socket check.
Request Quote — In Stock, 100% New & Original, Full Warranty