ADG506ATQ/883B
Product Specifications
ADG506ATQ/883B
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG506ATQ/883B from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG506ATQ/883B: Sixteen Channels, a 10.8 V to 16.5 V Window and Military Screening
The ADG506ATQ/883B is a 16-channel CMOS analogue multiplexer in a ceramic dual in line package screened to the military drawing. It switches one of sixteen inputs to a common output under the control of four binary address lines and an enable input, accepts TTL and 5 V CMOS logic levels, blocks signals up to the supplies in the off state, and guarantees break before make so two channels are never shorted together during a transition. The supply window is 10.8 V to 16.5 V in single or dual form, the absolute maximum supply rating is 44 V, maximum power dissipation is 28 uW, and typical leakage is 20 pA. The commercial equivalents are offered in DIP, SOIC, PLCC, TSSOP and LCCC packages.
The Q suffix is the ceramic package and the 883B suffix is the screening level, so this order code is bought for programmes that require the drawing rather than for a commercial board. The electrical behaviour is the same as the plastic part, and the two numbers that decide whether it fits are the supply window and the leakage.
Sixteen point five volts is exactly a plus or minus 15 V rail at plus 10 percent
The supply window ends at 16.5 V, and a plus or minus 15 V rail at plus 10 percent is 16.5 V, so an unregulated analogue supply that runs high sits exactly on the limit with no margin. A plus or minus 18 V rail is 1.5 V above the window and outside the part, even though the 44 V absolute maximum suggests otherwise: the absolute maximum is the point at which damage begins, not a usable operating point, and the analogue signal range is bounded by the supplies. A 15 V board should regulate the rail or accept that the top of the window is being used as an operating condition.
At the other end, 10.8 V is a plus or minus 5.4 V rail, which is comfortably below any plus or minus 5 V board and well below plus or minus 12 V. Between the two limits the part is specified, and 28 uW of maximum dissipation at 15 V is 1.87 uA, so the multiplexer is not a power term in a system that runs from a 15 V rail.
| Channels | 16 to 1, four address lines plus an enable |
| Supply window | 10.8 V to 16.5 V single or dual |
| Absolute maximum | 44 V, a damage limit and not an operating point |
| Signal range | Negative supply to positive supply |
| Power | 28 uW maximum, 1.87 uA at 15 V |
| Leakage | 20 pA typical, 20 mV into 1 GOhm and 0.2 V into 10 GOhm |
| Switching | Break before make guaranteed |
| Logic | TTL and 5 V CMOS compatible |
| Screening | 883B, ceramic package, full military drawing |
Twenty picoamps is nothing until the load is a gigohm
A leakage of 20 pA is invisible into a 10 kOhm load, where it develops 0.2 uV. Into 1 GOhm it is 20 mV and into 10 GOhm it is 0.2 V, so the leakage specification only becomes a system term when the multiplexer feeds a high impedance node: a pH probe, an electrometer front end, or a sample and hold with a small capacitor and a long dwell. That is exactly where a 16-channel multiplexer is often used, which is why the 20 pA figure is quoted rather than ignored.
The break before make guarantee matters in the same place. Without it, two channels are connected together for the duration of the transition, and if one of them is a low impedance source the other is pulled to it. The specification is a guarantee rather than a typical because the failure mode is a measurement that looks plausible and is wrong, which is the hardest kind to find in a qualification test.
Two questions buyers ask
Can the enable pin be used to sequence channels?
The enable disconnects all sixteen channels when it is de asserted, so it can be used to isolate the multiplexer from the common output during a channel change. It is not a per channel gate: the address lines select the channel and the enable gates the whole device. A board that needs to blank one channel while others remain connected needs a different topology.
Is the 883B version a different die?
It is the same die screened and packaged to the drawing, which covers the temperature range, the burn in and the traceability rather than a change in the electrical table. The practical consequence is that the 883B part is bought on the drawing number and not on a distributor description, and a commercial part in the same socket will perform the same function without the screening evidence.
Ordering and supply
The TQ suffix is the ceramic package and the 883B is the screening level. Substitution traps are the supply window, the leakage and the screening evidence: a part with a plus or minus 20 V window and 1 nA of leakage is electrically different at a gigohm source impedance, and a part without break before make changes the failure mode of a channel change. On a military programme the drawing number is the specification and the electrical table is secondary.
We hold and source this family for production and repair. Start at the analog mixed signal ICs family page, compare a candidate against the pin to pin cross reference, and where the multiplexer has to be replaced in an existing assembly, the order in how to verify a drop in replacement puts the supply window and the leakage first.
Request Quote — In Stock, 100% New & Original, Full Warranty