ADG1611BRUZ-REEL7
Product Specifications
ADG1611BRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1611BRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG1611BRUZ-REEL7: One Ohm Quad SPST, and the Logic That Turns On at Zero
The ADG1611BRUZ-REEL7 contains four independent single pole single throw switches in a 16-lead TSSOP, with 1 ohm typical on resistance, 1.6 ohm maximum over temperature, 0.2 ohm of on resistance flatness, and total harmonic distortion plus noise of 0.007 percent. It runs from plus or minus 3.3 V to plus or minus 8 V dual or 3.3 V to 16 V single, needs no separate logic supply, accepts 3 V logic with a 2.0 V high threshold and a 0.8 V low threshold, conducts equally in both directions, and blocks signals up to the supplies when off. Power dissipation is under 16 nW, and the package is the 16-lead TSSOP or the 4 mm by 4 mm LFCSP.
The family has three members and the difference is the control logic, not the switch. The ADG1611 turns a switch on with a logic zero, the ADG1612 turns it on with a logic one, and the ADG1613 mixes the two and adds break before make for multiplexing. That single inversion is the most common substitution failure in this family.
One ohm typical is 1.6 ohm guaranteed, and the flatness is a fifth of both
The guarantee over temperature is 60 percent above the headline, which changes what the switch does to a gain network. Into a 1 kOhm load, 1.6 ohm is 0.16 percent of gain error, which is comparable to the 0.1 percent resistors a precision stage is built from. Into 10 kOhm it is 0.016 percent and the switch stops mattering. The 0.2 ohm flatness is 20 percent of the 1 ohm typical figure, so the on resistance changes by a fifth across the signal range, and that change is what produces distortion rather than the absolute value: a 0.007 percent total harmonic distortion plus noise is minus 83.1 dB, or 13.8 bits, which sets the resolution ceiling for a signal routed through this part.
Sixteen nanowatts of dissipation is 4.8 nA at 3.3 V, which is small enough that the switch is not a power decision. What the CMOS construction does bring is a charge injection event at every switching edge and a capacitance that loads the node when off, and both are specified in the data sheet rather than in the summary. For a sample and hold, the charge injection into the hold capacitor is the number to read first.
| Configuration | Four independent SPST switches, bidirectional |
| On resistance | 1 ohm typical, 1.6 ohm maximum over temperature |
| Flatness | 0.2 ohm, 20 percent of the typical on resistance |
| Gain error | 0.16 percent into 1 kOhm, 0.016 percent into 10 kOhm |
| Distortion | 0.007 percent total harmonic distortion plus noise, minus 83.1 dB, 13.8 bits |
| Supplies | Plus or minus 3.3 V to plus or minus 8 V dual, 3.3 V to 16 V single |
| Logic | 3 V compatible, 2.0 V high and 0.8 V low, no logic supply pin |
| Control sense | On with logic zero on this part, inverted against the ADG1612 |
| Power | Under 16 nW, about 4.8 nA at 3.3 V |
| Packages | 16-lead TSSOP and 4 mm by 4 mm LFCSP |
The inverted control logic is the substitution trap
A reel of ADG1612 in a socket built for the ADG1611 makes every switch behave backwards: the channel that the firmware thinks it has closed is open and the one it thinks is open is closed. On a gain switching network that means the stage runs at the wrong gain and on a signal routing matrix it means two sources are connected at once. The parts are otherwise identical, so a functional test at power up with all control lines low will show continuity on all four channels and look like a short, not like a logic inversion.
The second trap is the supply. The dual range stops at plus or minus 8 V, so a plus or minus 10 V signal path is outside the part even though the 16 V single supply mode suggests otherwise. A plus or minus 5 V board has 3 V of headroom per rail, and a plus or minus 8 V board sits exactly on the limit with no allowance for a 10 percent rail. Single supply operation to 16 V covers a 12 V rail with 4 V to spare.
Two questions buyers ask
Can it replace a reed relay in a signal path?
Electrically it can, with two limits. The 1.6 ohm maximum on resistance is far above a reed relay contact, so a circuit that assumed a few milliohms has to be re checked, and the switch has no isolation in the relay sense: when off it blocks up to the supplies and presents a capacitance, not an open circuit. Above a few megahertz the off capacitance is the path that limits isolation.
What happens with a 3.3 V logic line and a plus or minus 5 V analogue supply?
The digital inputs are rated for 3 V logic and need no separate logic supply, so a 3.3 V microcontroller drives them directly. That is the point of the no logic supply arrangement: the level shift is inside the part, and the 2.0 V high threshold leaves 1.3 V of noise margin on a 3.3 V line, which is enough for a microcontroller pin and not much else.
Ordering and supply
The BRUZ suffix is the 16-lead TSSOP, lead free, in tape and reel. The three things to check against any candidate are the control sense, the 1.6 ohm maximum at temperature and the 8 V dual ceiling. A part that quotes 1 ohm typical without a maximum over temperature is quoting the room temperature bench number, and a part that quotes 5 ohm into the same socket changes the gain of every channel it feeds.
We hold and source this family for production and repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the pin to pin cross reference, and where the substitute has to be proven on a built board, the order in how to verify a drop in replacement puts the control logic and the supply ceiling ahead of the socket check.
Request Quote — In Stock, 100% New & Original, Full Warranty