MAX13487EESA+T
Product Specifications
MAX13487EESA+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX13487EESA+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
MAX13487EESA+T: a half duplex RS-485 transceiver that drives the bus without a direction pin
The MAX13487EESA+T is a 5 V, half duplex RS-485 compatible transceiver with 15 kV of ESD protection on the bus pins and a slew limited driver that reaches 500 kbps. Its AutoDirection control derives the driver enable from the data itself, so the UART transmit line drives the bus without a separate direction signal and without the firmware intervention that normally goes with it. On an isolated RS-485 port that removes a digital isolator channel, which is the reason the part exists.
Published values
| Parameter | Value |
|---|---|
| Interface | Half duplex RS-485 compatible, one driver and one receiver |
| Supply | 5 V |
| Data rate | 500 kbps, slew rate limited |
| ESD protection | 15 kV human body model on the bus pins |
| Direction control | AutoDirection, derived from the data |
| Shutdown current | 10 uA maximum |
| Hot swap | Supported, no false transitions on live insertion |
| Package | 8-pin SO, standard pinout |
AutoDirection removes a pin and a firmware task
A conventional RS-485 transceiver needs a driver enable that the firmware has to raise before the first byte and drop after the last one has left the shift register. Getting that timing wrong truncates the last byte or collides with another node. With the direction derived from the data, the UART transmit line can be connected directly, and on an isolated port the isolator needs one channel fewer, because the direction signal no longer has to cross the barrier.
The cost is that the part is not usable where the driver has to be held on with no data, for example as a bus bias or in a test mode that holds the line. In that case a conventional transceiver is still the right choice.
Slew limiting is what makes 500 kbps reliable on a long cable
The 500 kbps rate is lower than a fast RS-485 part can reach, and that is deliberate: the limited edge rate reduces reflections on an improperly terminated cable, so a two wire run through a building works without the bus failing at the ends. A 16 Mbps part in the same socket will show ringing and framing errors on the same cable, which is why the slower member of a family is sometimes the correct one.
Hot swap and ESD in the field
Hot swap capability means a node inserted into a live bus does not generate a false transition that the other nodes read as a start bit. Combined with 15 kV of ESD protection on the bus pins, the part covers the two field failures that return RS-485 boards most often: insertion transients and a discharge through a cable that was pulled out of a cabinet.
Two pages worth reading before a purchase order goes out are defense grade components and component lead time solutions; the first lists what else fits the socket, the second is the test sequence for a drop in, and vendor consolidation covers the case where the shortage is already on the line.
Two questions buyers ask
Does the MAX13487E need a direction pin connected? No, the direction is derived from the data. The driver enable function is internal, which is why the pin count is eight and the isolator channel count can be reduced.
Can it be used at 3.3 V? No, this part is a 5 V device. A 3.3 V RS-485 port needs a different family member, and the bus levels have to be checked against the other nodes before mixing supplies on one cable.