LTM8083EY#PBF
Product Specifications
LTM8083EY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8083EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8083EY: the E grade module and the guarantee behind the same part number
The LTM8083EY is the E grade of the 36 V buck-boost module: 3 V to 36 V input, 1 V to 36 V output, 1.5 A with 12 V at 1.5 A available from either a 12 V or a 36 V input, a 1 V reference, a 300 kHz to 2 MHz switching frequency with synchronisation, adjustable current limit, output current monitoring and CISPR25 Class 5 compliance, in a 6.25 mm by 6.25 mm by 2.22 mm BGA with SAC305 balls and an MSL 3 rating. The order table gives the E and the I grade the same minus 40 to 125 degree range, so the letter is about the guarantee and not about the temperature.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 3 V to 36 V |
| Output voltage | 1 V to 36 V |
| Output current | 1.5 A, 0.8 A at 12 V out from 6 V in |
| Feedback reference | 1 V, plus or minus 1.5 percent |
| Switching frequency | 300 kHz to 2 MHz, synchronisable |
| Current limit | adjustable |
| Current monitoring | analogue output proportional to the sensed current |
| Package | 6.25 mm by 6.25 mm by 2.22 mm BGA |
| Ball finish | SAC305, RoHS compliant |
| Moisture sensitivity | MSL 3 |
| Temperature grade | E, from minus 40 to 125 degrees |
| Order code | LTM8083EY#PBF, tray |
E and I share a range, and the difference is paperwork
Both grades are listed from minus 40 to 125 degrees in the order table, and both are the same module. The E grade is tested at 25 degrees with the rest assured by characterisation and correlation, and the I grade is guaranteed over the full range. For a product that validates the converter as part of a system, the E grade is the right buy and the cheaper one; for a product whose qualification report quotes the module's limits at the extremes, the I grade is what supports that sentence.
This is the kind of distinction that gets lost between a prototype bill of materials and a production one. The two parts are interchangeable on the board, they reflow identically, and they differ only in which temperature the limits are promised at. Writing the grade into the approved vendor list with the reason attached is cheaper than rediscovering it during a second source review.
MSL 3 and a BGA on the underside of a board
An MSL 3 rating means the package can be out of its dry pack for 168 hours at 30 degrees and 60 percent relative humidity before it needs baking. A module contains an inductor and a moulded body, so the rating matters for the reflow profile and for the floor life of a partly built board, and a BGA that has absorbed moisture can delaminate at reflow in a way that only shows up as an intermittent later.
Putting the module on the underside means it sees the second reflow, which is the one that runs with the heavy components already attached. The 2.22 mm height and the BGA array are what make that workable, and the pickup and placement nozzle for a 6.25 mm square module is a standard tool rather than a special one. What is not standard is the rework: a BGA module with a thermal pad pattern under it is not a part that gets replaced with a hot air gun on the bench.
What the module removes from the schedule
A discrete buck-boost of the same capability is a controller, two switches, an inductor, a sense resistor, a compensation network, a soft start capacitor and the characterisation of all of them across 3 V to 36 V of input. The module replaces that with a divider, two capacitors and a frequency resistor, and it moves the electromagnetic compatibility from an engineering task to a specification.
The cost is board area, height flexibility and the inability to change the inductor. When the input range is fixed and the current is modest, a discrete converter is smaller and cheaper. When the input range crosses the output, the module is usually the faster route to a working board, and the schedule it saves is worth more than the price difference on any programme with a qualification date.
When an order code in this family cannot be found, the power management cross reference lists what else does the same job, BOM shortage recovery covers what to check before a part is dropped into an existing board, and OEM procurement is the route we take on a live shortage.
Two questions buyers ask
Is the E grade a different temperature range from the I grade? No. Both are listed from minus 40 to 125 degrees. The I grade is guaranteed over that range while the E grade is tested at 25 degrees with the rest assured by characterisation.
What does the MSL 3 rating mean for assembly? The package can be out of its dry pack for 168 hours at 30 degrees and 60 percent humidity before baking is required. Since the module is often placed on the underside and sees a second reflow, the floor life and the bake schedule have to be part of the assembly instruction.