Contact Us

LTM8065EY#PBF

Brand: Analog Devices
Analog Devices LTM8065EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8065EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8065EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8065EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8065EY: a 2.5 A, 40 V module for room temperature equipment

The LTM8065EY#PBF carries the same 2.5 A continuous, 3.5 A peak rating, the same 0.97 V to 18 V output range and the same 200 kHz to 3 MHz switching span as the industrial code, in the same 6.25 mm square 2.32 mm tall package, with the guarantee moved to 0 to +125 degrees internal. It is the part for instrumentation, test equipment and mains powered industrial boxes where the ambient is controlled and the margin is spent on efficiency rather than on a cold start window nobody will test.

Published values

ParameterValue
Input range3.4 V to 40 V
Output range0.97 V to 18 V
Continuous current2.5 A
Peak current3.5 A at 3.3 V out, 1 MHz
Feedback voltage970 mV nominal
Switching frequency200 kHz to 3 MHz
Guaranteed range0 to +125 degrees internal
Shutdown current3 microamps into VIN
No load current5 microamps with BIAS at 5 V
Output ripple10 mV at 2.5 A
Power good window1.05 V falling, 0.89 V rising
Package6.25 mm by 6.25 mm by 2.32 mm BGA, 0.5 g
Thermal21 degrees per watt to ambient, 5.9 to the board
BIAS minimum3.2 V

Where the E grade saves money without losing margin

The guarantee boundary only matters against the coldest ambient in the product specification. A rack instrument rated 5 to 40 degrees, a laboratory supply or a piece of bench test gear never runs below 0, so the industrial window is buying insurance against a condition the product does not claim. The saving is not only on the part: the E grade is usually the higher volume code and therefore the one that is on the shelf when a build is pulled forward.

What the E grade does not save is thermal margin. The 21 degrees per watt path, the 1.9 W of dissipation at an 85 degree ambient and the efficiency floor that follows are identical, and a board that overheats on the I grade overheats on the E grade in exactly the same place.

Reading the power good window as a percentage

The comparator sits on the feedback node, so its thresholds scale with the reference: 1.05 V falling is 8.25 percent above 970 mV and 0.89 V rising is 8.25 percent below it. On a 5 V rail that is a 4.59 V to 5.41 V window, which is wider than the 5 percent supply tolerance most loads assume, so power good alone will not catch a rail that is 6 percent low.

On a 1.2 V rail the same 8.25 percent is 99 mV, and a load that needs 3 percent accuracy has to be protected by its own supervisor rather than by this flag. The pin is a sequencing signal, not a precision monitor.

Soft start, inrush and the 3.5 A peak

The 3.5 A peak is 40 percent above the continuous rating, which is enough for a load step but not for charging a large output capacitance at full current. The TRSS pin sets the ramp with a 2 microamp source, so a 10 nanofarad capacitor gives a slow enough rise that the peak is never reached during startup, and that is the cheapest way to keep a board inside the current limit.

The same pin pulls down at 200 ohms on a fault, which resets the ramp for the next attempt. On a rail that feeds a hot pluggable load, that behaviour is what stops a short from turning into a repeated inrush event.

Where a customer needs a second position on this part, how to verify a drop in replacement is the starting point, vendor consolidation sets out the checks a substitution has to pass, and the power management cross reference is the short lead time route we quote against.

Two questions buyers ask about the commercial code

Is the E grade pin compatible with the I grade? Yes, identical ball out and identical external components. The only change on a drawing is the order code and the temperature note in the specification.

Does the E grade still carry the 18 V output option? Yes, the output range is a property of the die and the internal inductor, not of the grade. What differs is the temperature window over which the limits are promised.