Contact Us

LTM8063IY#PBF

Brand: Analog Devices
Analog Devices LTM8063IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8063IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8063IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8063IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8063IY: 2 A at 40 V in from a 6.25 by 4 mm package

The LTM8063IY#PBF is a 40 V, 2 A continuous and 2.5 A peak step-down module in a 6.25 mm by 4 mm by 2.22 mm BGA, with a 0.8 V to 15 V output range and 200 kHz to 2.2 MHz switching. It is the middle of the 40 V Silent Switcher family: more current than the 4 mm part, a wider output range than the 1.2 A part, and a thermal path of 41.5 degrees per watt that sits between them. The module can also be wired as an inverter, which is how a negative rail gets built from the same reel as the positive one.

Published values

ParameterValue
Input range3.2 V to 40 V
Output range0.8 V to 15 V
Continuous current2 A at 12 V in, 5 V out, 85 degree ambient
Peak current2.5 A at 3.3 V out and 1 MHz
Switching frequency200 kHz to 2.2 MHz; RT of 232k, 41.2k and 15.8k for the three points
Feedback voltage774 mV nominal, 760 mV to 786 mV over temperature
Line and load regulation0.5 percent and 0.5 percent
Output ripple15 mV at 2 A
Shutdown current3 microamps with RUN at 0 V
No load current8 microamps not switching
Power good window0.84 V falling and 0.70 V rising against a 774 mV reference
SYNC threshold0.4 V to 1.5 V; spread spectrum enabled above 2.9 V
PackageBGA, 6.25 mm by 4 mm by 2.22 mm, 0.14 g, MSL 3
Thermal41.5 degrees per watt to ambient, 13 to the board, 52.4 to the top
Temperature grade-40 to +125 degrees internal, TJ maximum 125 degrees

The current rating, the voltage and the ambient are one number

Forty degrees of headroom at 41.5 degrees per watt is 0.96 W. At 3.3 V and 2 A, 6.6 W out, the efficiency floor is 87.3 percent and the module meets it. At 5 V and 2 A, 10 W out, the floor is 91.2 percent and the margin is thin. At 15 V and 2 A, 30 W out, the floor is 96.9 percent, which is a different part's job.

The 2 A rating in the features line is quoted at 12 V in and 5 V out with an 85 degree ambient, which is the 91.2 percent case. That is the honest operating point to plan around. A 12 V output at 2 A needs airflow or a lower ambient, and a 15 V output at 2 A needs both.

Inverter configuration, and the level shift it requires

Wiring the module as an inverting converter produces a negative rail from the same part number, which is useful where an analogue front end needs plus and minus 5 V or plus and minus 12 V. The output is regulated against the feedback node and the RUN pin has to be driven relative to the negative rail, so the enable signal needs a level shift and the input current rises by the ratio of the two voltages.

The power good pin is referenced the same way and cannot be tied to the positive rail's logic directly. On a dual rail build, treat the negative converter's control pins as a separate domain and keep the two domains apart until the last possible point.

Spread spectrum, and when it is the wrong choice

Driving the SYNC pin above 2.9 V enables spread spectrum, which dithers the switching frequency to spread the emission energy. It is what makes a small module pass a conducted emissions limit with a modest input filter, and it costs a little efficiency and a little output ripple because the loop is being asked to track a moving frequency.

It is the wrong choice when several modules share a clock or when a receiver has a narrow band that the dither would sweep through repeatedly. In those cases the external synchronization input is the better tool: everything runs at one frequency, and the filter can be tuned to that frequency instead of to a band.

Sourcing notes for this family: the power management cross reference holds the cross references, BOM shortage recovery is the pre substitution check, and how to reduce component cost is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask about the 2 A module

What is the difference between the 774 mV and the 970 mV members of this family? Different dies and different internal references. A divider computed for one is wrong on the other by 20 to 25 percent. Always take the reference from the data sheet of the exact order code.

Can two modules be paralleled for 4 A? Not by tying the outputs. The current limit is per module and there is no sharing bus, so two modules in parallel will not split a load evenly. Either move up to a part rated for the current or accept a two rail arrangement.