Contact Us

LTM8055MPY#PBF

Brand: Analog Devices
Analog Devices LTM8055MPY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8055MPY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8055MPY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8055MPY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8055MPY: 8.5 A buck-boost that is a thermal problem before it is a current problem

The LTM8055MPY#PBF is a 36 V buck-boost module rated 8.5 A at 12 V out from 24 V in, in a 15 mm by 15 mm by 4.92 mm package. Output can be above, equal to or below the input, from 1.2 V to 36 V, and the module includes the controller, the four switches and the inductor. Input and output average current limits are adjustable and both are monitored, which is what makes it usable as a battery charger or a current limited source rather than only as a voltage regulator. The MP grade is guaranteed over -55 to +125 degrees internal.

Published values

ParameterValue
Input range5 V to 36 V
Output range1.2 V to 36 V, above, equal to or below the input
Output current3 A at 6 V in and 12 V out; 8.5 A at 24 V in and 12 V out
Efficiencyup to 97.5 percent
Switching frequency100 kHz to 800 kHz; RT of 453k gives 100 kHz, 24.9k gives 800 kHz
Synchronisationexternal clock from 200 kHz to 700 kHz
Feedback voltage1.2 V nominal, 1.188 V to 1.212 V at 25 degrees, 1.176 V to 1.220 V over temperature
Current sense thresholds56 mV on the input, 61.5 mV on the output, both adjustable through CTL
Current monitorsIINMON at 0.96 V to 1.04 V, IOUTMON at 1.14 V to 1.26 V at the limits
Quiescent current0.1 microamp typical, 1 microamp maximum, with RUN low
No load current8 mA in discontinuous mode, 45 mA in forced continuous mode
Line and load regulation0.5 percent and 0.5 percent
Output ripple25 mV RMS at 12 V in and 3 A
Package121 lead BGA, 15 mm by 15 mm by 4.92 mm
Thermal20.5 degrees per watt to ambient, 11.0 to the board
Temperature grade-55 to +125 degrees internal

Where 8.5 A actually lands

Twelve volts at 8.5 A is 102 W. At the headline 97.5 percent efficiency the loss is 2.6 W, and through 20.5 degrees per watt that is a 53 degree rise, so an 85 degree ambient puts the junction at 138 degrees, past the 125 degree limit. The 8.5 A figure therefore belongs to a 70 degree ambient at best, or to a board with airflow over the 225 square millimetre package.

At 6 V in and 12 V out the module is in boost mode and 3 A out means 36 W, which needs about 6.3 A from the 6 V input at 95 percent efficiency. Input current, not output current, is what sizes the connector, the input capacitor and the trace width in that mode.

Two current limits, and why a battery charger needs both

The input average current limit protects the source, and the output average current limit protects the load. On a charger the output limit sets the charge rate and the input limit keeps the wall adapter inside its rating; on a motor supply the input limit stops a stall from collapsing the bus. Both are set by a voltage on a control pin, so a microcontroller can move them at run time.

The monitor outputs are what make that closed loop possible: IOUTMON reads 1.14 V to 1.26 V at the output current limit, so the host can read the actual current rather than assume it. A 5 milliohm sense resistor at the 61.5 mV threshold sets an 12.3 A limit, which is above the 8.5 A rating and therefore a protection level rather than an operating point.

Buck-boost modes and the efficiency cliff

Around the point where VIN equals VOUT the module passes through a transition region, and that is where efficiency dips and output ripple rises. A 12 V rail from a 12 V nominal battery spends a lot of time in that region, which is why the data sheet shows separate curves for buck, pass-through and boost.

Holding the output a few hundred millivolts away from the input avoids the worst of it where the load allows. Where the output must equal the input, plan the thermal budget from the transition curves, not from the 97.5 percent headline, which is a buck mode number near the top of the input range.

When an order code in this family cannot be found, the power management cross reference lists what else does the same job, OEM procurement covers what to check before a part is dropped into an existing board, and component lead time solutions is the route we take on a live shortage.

Two questions buyers ask about the buck-boost

What is the difference between the LTM8055 and the LTM8055-1? The -1 version brings the compensation network out to pins, which allows the loop to be tuned for a load or an output capacitor outside the standard range. The plain version is internally compensated and is the simpler part to use.

Can it work as a current source for an LED string? It can regulate output current, but the LTM8052 in the same family is the part built for constant current with two quadrant operation. Use the 8055 where the requirement is a voltage rail with a current cap.