LTM8054MPY#PBF
Product Specifications
LTM8054MPY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8054MPY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8054MPY: 5.4 A buck-boost, 3.42 mm tall, to -55 degrees
The LTM8054MPY#PBF is the extended temperature member of the 36 V buck-boost family, rated 5.4 A at 12 V out from 24 V in, in an 11.25 mm by 15 mm by 3.42 mm package. It is 1.5 mm thinner than the 8.5 A part and has a lower junction to ambient resistance, 17.6 degrees per watt against 20.5, because the smaller package sits closer to the board. Output spans 1.2 V to 36 V with the input allowed to be above, equal to or below it, and both input and output average current limits are adjustable. Guaranteed over -55 to +125 degrees internal.
Published values
| Parameter | Value |
|---|---|
| Input range | 5 V to 36 V |
| Output range | 1.2 V to 36 V |
| Output current | 1.8 A at 6 V in and 12 V out; 3.4 A at 12 V in; 5.4 A at 24 V in |
| Efficiency | up to 94 percent |
| Switching frequency | 100 kHz to 800 kHz |
| Feedback voltage | 1.2 V nominal, 1.188 V to 1.212 V at 25 degrees |
| Current sense thresholds | 56 mV on the input, 61.5 mV on the output |
| Quiescent current | 0.1 microamp typical with RUN low |
| No load current | 8 mA discontinuous, 45 mA forced continuous |
| Line and load regulation | 0.5 percent and 0.5 percent |
| Output ripple | 25 mV RMS at 24 V in and 3 A |
| Package | BGA, 11.25 mm by 15 mm by 3.42 mm |
| Thermal | 17.6 degrees per watt to ambient, 5.9 to the board, 10.7 to the top |
| Temperature grade | -55 to +125 degrees internal, guaranteed by test |
5.4 A has a lower ambient attached than it looks
Twelve volts at 5.4 A is 64.8 W. At the headline 94 percent efficiency the loss is 4.1 W, and through 17.6 degrees per watt that is a 73 degree rise. An 85 degree ambient would put the junction at 158 degrees, well past the 125 degree limit, so 5.4 A belongs to roughly a 50 degree ambient in still air, or to a board with airflow.
The 3.42 mm height helps here: the thinner package has a shorter thermal path to the board, which is why the resistance is 17.6 rather than 20.5. That advantage only materialises if the board under the part is solid copper with vias. On a sparse board the package sits on a poor heat spreader and the published number is not reachable.
Six volts in, twelve volts out, 1.8 A out and 4 A in
In boost mode the input current is what limits the converter. At 6 V in and 12 V out with 1.8 A out, the output is 21.6 W and at 90 percent efficiency the input is 24 W, which is 4 A from a 6 V source. Connectors, fuses and the input capacitor all see 4 A, not 1.8 A.
The input average current limit is what keeps that within a supply's rating, and it is set by a resistor and a control voltage rather than by a fixed internal value. On a 6 V battery pack with a 3 A fuse, the limit has to be below 3 A, which caps the output at about 1.3 A rather than 1.8 A.
Thin package, cold temperature, sealed enclosure
A 3.42 mm module fits under a card cage or inside a sealed box with a 4 mm internal clearance, which is where the 4.92 mm part does not go. Sealed boxes are also where the -55 degree grade earns its price: an unheated outdoor enclosure in a cold climate is exactly the case where the E and I grades stop being specified and the MP grade continues.
The MP grade guarantees the table over -55 to +125 degrees, which is the only full range guarantee in this family. It comes with longer lead times and a price premium, so it belongs where the product specification actually claims the range.
Buyers usually arrive at the power management cross reference to find the family alternatives, then use medical device components to confirm a substitute before it is fitted; the pin to pin cross reference is the routine for a part that has already stopped shipping.
Two questions buyers ask about the thin buck-boost
Can the 5.4 A module be paralleled for more current? The family allows paralleling for increased output current, but the two modules then need a shared current limit signal and matched sense resistors. Below 8.5 A, moving to the larger part is the simpler route.
What is the minimum input at full output? 5 V, and at that input the module is in heavy boost and the input current is several times the output current. The thermal and connector budget has to be built from the input side in that corner.